2 layers63.3 × 63.1 mm
Nano drone
radioelf/nano_Drone_ESP32
Small drone with ESP32 to experiment with this https://github.com/rtlopez/esp-fc
59 parts
2 layers
PCB arduino Due para DuePi y Gpio Raspberry Pi
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 120
- Nets
- 172
- Pads
- 486
- Tracks, vias
- 1,465, 124
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20170123)
- Created
- 8 Feb 2017
- Updated
- 18 Apr 2017
Overview
DuePi is an open-source printed circuit board by radioelf, from the radioelf/Arduino-Due-mod-for-GPIO-compatible-Raspberry-Pi repository on GitHub. It is a 2-layer board with 120 parts on 172 nets, routed with 1,465 tracks and 124 vias.
It is built around the ATMEGA16U2-MU, ATSAM3X8EA-AU and LMV358IDGKR, with the CG0603MLC-05E, MH2029-300Y and FDN340P among its other parts. Its parts include 43 capacitors, 25 resistors, 8 diodes, 6 inductors and 5 ICs. It belongs with the AVR (ATmega, ATtiny) and SAM D and SAM boards of this library.
Main components
12
ATMEGA16U2-MU
QFN-32-EP(5x5)-40℃~+85℃ 16KB 16MHz 2.7V~5.5V 22 512Byte 512Byte 8 Bit AVR Built-in FLASH QFN-32-EP(5x5) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
ATSAM3X8EA-AU
LQFP-144(20x20)-40℃~+85℃ 1.62V~3.6V 100KB 103 12bit 12bit 32 Bit 512KB 84MHz ARM Cortex-M3 Built-in FLASH LQFP-144(20x20) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
LMV358IDGKR
UncategorisedUnknown maker
CG0603MLC-05E
0603-55℃~+125℃ 0.2pF 1 10nA 30V 5V Bidirectional IEC 61000-4-2 0603 ESD and Surge Protection (TVS/ESD) ROHSBournsVaristors
MH2029-300Y
0805-55℃~+125℃ 1 30Ω@100MHz 3A 3mΩ ±25% 0805 Ferrite Beads ROHSBournsFerrite Beads
FDN340P
SOT-23-55℃~+150℃ 1 P-Channel 1.5V 121pF 20V 2A 500mW 56pF 7.2nC@4.5V 70mΩ@4.5V 779pF P-Channel SOT-23 MOSFETs ROHSonsemiMOSFETs
0ZCA0035FF2G
12061206 Chip Resistor - Surface Mount ROHSBel FuseChip Resistor - Surface MountBC847
SOT-231 NPN 100MHz 100mA 100nA 110 200mW 45V 500mV 6V NPN SOT-23 Bipolar (BJT) ROHSShikuesBipolar (BJT)DMG2305UX
SOT-23-55℃~+150℃ 1 P-Channel 1.7W 190pF 1V 20V 4.1A 52mΩ@4.5V 7.8nC 740pF P-Channel SOT-23 MOSFETs ROHSTECH PUBLICMOSFETsKNH16C104DA5TS
SMD-4P,1.6x0.8mmSMD-4P,1.6x0.8mm EMI/RFI Filters (LC, RC Networks) ROHSKyocera AVXEMI/RFI Filters (LC, RC Networks)
PESD0402-140
0402-55℃~+125℃ 0.25pF 10uA 14V 40V Bidirectional ESD IEC 61000-4-2 0402 ESD and Surge Protection (TVS/ESD) ROHSLittelfuseESD And Surge Protection (TVS/ESD)
SMBJ5V0A
SMB(DO-214AA)-55℃~+150℃ 5V 600W@10/1000us 65.2A@10/1000us 7V 800uA 9.2V Single-channel TVS Unidirectional SMB(DO-214AA) ESD and Surge Protection (TVS/ESD) ROHSonsemiESD And Surge Protection (TVS/ESD)
README
README.mdArduino Due mod for GPIO compatible Raspberry Pi
Creative Commons License Disclaimer
UNLESS OTHERWISE MUTUALLY AGREED TO BY THE PARTIES IN WRITING, LICENSOR OFFERS THE WORK AS-IS AND MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND CONCERNING THE WORK, EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF TITLE, MERCHANTIBILITY, FITNESS FOR A PARTICULAR PURPOSE, NONINFRINGEMENT, OR THE ABSENCE OF LATENT OR OTHER DEFECTS, ACCURACY, OR THE PRESENCE OF ABSENCE OF ERRORS, WHETHER OR NOT DISCOVERABLE. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES, SO SUCH EXCLUSION MAY NOT APPLY TO YOU. EXCEPT TO THE EXTENT REQUIRED BY APPLICABLE LAW, IN NO EVENT WILL LICENSOR BE LIABLE TO YOU ON ANY LEGAL THEORY FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES ARISING OUT OF THIS LICENSE OR THE USE OF THE WORK, EVEN IF LICENSOR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Parts
120| Qty | Value | Footprint | References |
|---|---|---|---|
| 23 | 100nF | Capacitors_SMD:C_0402 | C1, C2, C3, C11, C12, C13, C14, C15, C16, C17, C19, C20, C23, C31, C32, C37 +7 |
| 8 | 10uF | Capacitors_SMD:C_1210_HandSoldering | C7, C8, C10, C18, C22, C35, C36, C40 |
| 7 | 1K | Resistors_SMD:R_0402 | R11, R12, R14, R15, R17, R22, R23 |
| 7 | 22pF | Capacitors_SMD:C_0402 | C24, C25, C26, C27, C28, C29, C30 |
| 5 | CG0603MLC-05E | Inductors_NEOSID:Neosid_Inductor_SM0603CG | VR1, VR2, VR3, VR4, VR5 |
| 5 | MH2029-300Y | Resistors_SMD:R_0805 | L1, L2, L3, L4, L5 |
| 4 | 10K | Resistors_SMD:R_0402 | R9, R10, R13, R16 |
| 3 | 100K | Resistors_SMD:R_0402 | R1, R18, R20 |
| 3 | FDN340P | dronpi:SOT23-3 | Q1, Q2, Q4 |
| 2 | 10nF | Capacitors_SMD:C_0402 | C21, C34 |
| 2 | 1K5 | Resistors_SMD:R_0402 | R24, R25 |
| 2 | 22R | Resistors_SMD:R_0402 | R7, R8 |
| 2 | 39R | Resistors_SMD:R_0402 | R3, R4 |
| 2 | MF-MSMF050-2 500mA | Inductors_NEOSID:Neosid_Inductor_SM-NE45_SMD1812 | F1, F2 |
| 2 | USB-B-AB | Connect:USB_Micro-B | P1, P2 |
| 1 | 0R | Resistors_SMD:R_0402 | R2 |
| 1 | 0ZCA0035FF2G | dronpi:Fuse_SMD1206_Wave | F3 |
| 1 | 100uF | Capacitors_Tantalum_SMD:TantalC_SizeD_EIA-7343_Reflow | C42 |
| 1 | 12Mhz | Crystals:Crystal_SMD_2520_4Pads | Y1 |
| 1 | 16Mhz | Crystals:Crystal_SMD_2520_4Pads | Y3 |
| 1 | 1K7 | Resistors_SMD:R_0402 | R21 |
| 1 | 1M | Resistors_SMD:R_0402 | R6 |
| 1 | 1uF | Capacitors_SMD:C_0402 | C33 |
| 1 | 32.768Khz | Crystals:Crystal_SMD_5032_2Pads | Y2 |
| 1 | 3v3 | Measurement_Points:Measurement_Point_Round-TH_Small | JTAG7 |
| 1 | 3v3 | dronpi:LED_0603 | D7 |
| 1 | 47uF | Capacitors_SMD:C_1210_HandSoldering | C39 |
| 1 | 4k7 | Resistors_SMD:R_0402 | R19 |
| 1 | 5v | dronpi:LED_0603 | D6 |
| 1 | 6k8 | Resistors_SMD:R_0603 | R5 |
| 1 | 74LVC1G125-SOT353 | Tinkerforge:SC70-5 | IC3 |
| 1 | ATMEGA16U2 | SparkFun:MLF32-PAD | IC2 |
| 1 | ATSAM3X8EA-AU | Housings_QFP:LQFP-144_20x20mm_Pitch0.5mm | IC1 |
| 1 | BC847 | dronpi:SOT23-3 | Q3 |
| 1 | CD1208 | Diodes_SMD:D_0603 | D3 |
| 1 | DMG2305 | dronpi:SOT23-3 | Q5 |
| 1 | DronPi_GPIO | dronpi:raspberrypi2 | J1 |
| 1 | ERASE | Buttons_Switches_SMD:SW_SPST_EVQPE1 | SW2 |
| 1 | GND | Measurement_Points:Measurement_Point_Round-TH_Small | JTAG6 |
| 1 | GND | Measurement_Points:Measurement_Point_Square-TH_Small | PAD3 |
| 1 | ICSP1 | Pin_Headers:Pin_Header_Straight_2x03 | P3 |
| 1 | KNH16C104DA5TS | dronpi:KYOCERA-KNH16-DA | L6 |
| 1 | LMV358IDGKR | SparkFun:MSOP8 | U1 |
| 1 | M_RESET | Measurement_Points:Measurement_Point_Round-TH_Small | JTAG5 |
| 1 | NCP1117ST33T3G | TO_SOT_Packages_SMD:SOT-223 | IC4 |
| 1 | OSHW-LOGOL | Symbols:OSHW-Logo2_7.3x6mm_SilkScreen | M1 |
| 1 | PESD0402-140 | Capacitors_SMD:C_0402 | D5 |
| 1 | RESET | Buttons_Switches_SMD:SW_SPST_B3S-1000 | SW1 |
| 1 | RX | dronpi:LED_0603 | D1 |
| 1 | RX | Measurement_Points:Measurement_Point_Square-TH_Small | PAD2 |
| 1 | SMBJ5V | Tinkerforge:DO-214AA | D4 |
| 1 | TCK | Measurement_Points:Measurement_Point_Round-TH_Small | JTAG4 |
| 1 | TDI | Measurement_Points:Measurement_Point_Round-TH_Small | JTAG3 |
| 1 | TDO | Measurement_Points:Measurement_Point_Round-TH_Small | JTAG2 |
| 1 | TMS | Measurement_Points:Measurement_Point_Round-TH_Small | JTAG1 |
| 1 | TX | Measurement_Points:Measurement_Point_Square-TH_Small | PAD1 |
| 1 | TX | dronpi:LED_0603 | D2 |
| 1 | Yellow | dronpi:LED_0603 | D8 |
Similar boards
- 6 layers70 × 40.5 mm
FMUv246-imported
yagamy4680/drone-study
AUAV-OpenSource/FMUv4-PixRacer is the open hardware design of PixHawk FMUv4. It uses STM32F427 and MPU6000. (github)
290 parts - 6 layers70 × 40.5 mm
PX4FMUv2.4
lachlanA/eagle-to-kicad
Eagle SCH/LIB to KiCad SCH/LIB ULP conversion script
354 parts429GPL-2.0 - 2 layers101.6 × 53.4 mm
- 4 layers101.6 × 53.3 mm
- 2 layers68.6 × 53.3 mm
- 2 layers101.6 × 53.3 mm
ADK MEGA 2560-REV3-append
sirkha/3D-Components
These are various components and assemblies that I have modeled for use in designing 3D printed objects.
100 parts - 2 layers68.6 × 53.3 mm
Leonardo Rev3e
trfaa001/Potentiometer-pedals-to-USB
Arduino project that uses potentiometers as game pedals.
61 partsGPL-3.0
Questions
What parts does the DuePi use?
120 parts, built around the ATMEGA16U2-MU, ATSAM3X8EA-AU, LMV358IDGKR and CG0603MLC-05E. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the DuePi KiCad files?
From the radioelf/Arduino-Due-mod-for-GPIO-compatible-Raspberry-Pi repository on GitHub, at the commit this page was made from: the board is DuePi.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the DuePi design in my own project?
Its repository states no licence, so its author keeps all rights: ask radioelf before reusing the design.