

Midea WiFi Dongle
Midea dongle, complete remaking of the reneklootwijk project/repository, with ESP32 C6 and single plate for tracks
- Size
- 23 × 41 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 20
- Nets
- 25
- Pads
- 64
- Tracks, vias
- 155, 4
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 15 Nov 2025
- Updated
- 1 Dec 2025
Overview
Midea WiFi Dongle is an open-source printed circuit board by SaschaKP, from the SaschaKP/midea-dongle repository on GitHub. It is a 2-layer board of 23 × 41 mm with 20 parts on 25 nets, routed with 155 tracks and 4 vias.
It is built around the AMS1117-3.3 and BSS138. Its parts include 7 resistors, 3 capacitors, 2 ICs, 2 transistors and 2 switches. It belongs with the radio and wireless boards of this library.
Main components
2AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsBSS138
SOT-23-55℃~+150℃ 1 N-channel 1.1Ω@10V、1.2Ω@4.5V 1.2V 1.7nC@10V 17.5pF 340mA 350mW 50V 6.5pF N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETs
README
README.mdMidea WiFi Dongle - v3
This repo is a complete rework of Rene Klootwijk's repository. So credits for the initial hardware study and design go to him!
I've made a lot of changes to the board:
- the board will fit inside the original spacer, occuping the original space, but without casing
- all pads can be soldered with hot-air gun and soldering paste, they are slightly larger for that purpose in mind
- it uses an ESP32 C6 and the software for making it work with this dongle (esphome) can be found in my repository
- Converted the KiCad project to KiCad 9
For this particular repository you can use an ESP32 C6 MINI (WT0132C6-S5) that can be used as a drop-in replacement for ESP-12F
That's what the board now looks like:

PCB and Parts
- The buttons are 3x4mm in size. Height is up to your liking. Can easily be found on AliExpress:

- Specs of the USB jack, can also be found on AliExpress:

- LDO Caps (C1 & C2) can be either tantalum or ceramic: Officially should be tantalum, but ceramic work just fine.
- Remember that the WT0132C6-S5 (ESP32 C6 MINI) is interchangeable with ESP-12F or ESP-07 which offers an external antenna:

I highly recommend taking a look at the iBOM file that can also be found in the "production-files" folder. It makes sourcing the parts and soldering so much easier!
Making of PCB
You will find some files to print for classic paper-toner-iron transfer on copper for etching, or you can also use a more modern approach with a 3D printer (with 0.25 or less nozzle) with spray painting or top of the model to track the negative part, etching as usual with acid and subsequent protective paint upon tracks to avoid potential short circuits later.
If you are familiar with this kind of prototyping you will find what you need inside the print_file directory

Flashing
Flashing the ESP can be done using any USB-to-UART adapter. I recommend getting an USB-A-socket cable with open ends, so you can crimp a dupont at the open end. So TX from the dongle goes to RX on the UART adapter and RX from the dongle goes to TX on the UART adapter. Set the UART adapter to 5V. Yes, it is safe. You will not burn the ESP in this case! The board has two mosfets that will switch the pins to 3v3. Now how to actually flash the board:
- Create a new device under "ESPHome Builder" in Home Assistant. Choose
ESP32 C6 devkitmas board - You can find an example config under "esphome". Edit the config in ESPHome builder and substitute the placeholders and potentially the board.
- Install and download.
- Now open ESPHome Web
- Connect the UART adapter to your PC, but not the dongle just yet!
- Hold the "PRG" button on the dongle and keep holding it!
- Now connect the dongle to the UART adapter.
- Click "Connect" on ESPHome Web, select the UART adapter, click "Install", select the bin you've just built and downloaded and flash it.
- As soon as it says "Erasing" or "Flashing", you can release the "PRG" button.
- Wait for it to be installed and it will show up in your Wi-Fi and under "Devices" in Home Assistant
Parts
20| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1, R2, R3, R4, R5, R6, R7 |
| 2 | 22uF | Andys-Footprints:CP_1.62x0.84mm_0603_1608metric_HandSolder | C1, C2 |
| 2 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | SW_Push | Button_Switch_SMD:SW_Push_SPST_NO_Alps_SKRK | SW1, SW2 |
| 1 | 100nF | Capacitor_SMD:CP_1.62x0.84mm_0603_1608Metric | C3 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223 | U1 |
| 1 | LOGO | Andys-Footprints:Yoshi-Egg-Small | G1 |
| 1 | USB_A | Connector_USB:USB_A_CNCTech_1001-011-01101_Horizontal | J1 |
| 1 | WT0132C6-S5 | RF_Module:WT0132C6-S5 | U2 |
The 18 most common of 20 parts.
Similar boards
- 2 layers44.2 × 29.3 mm

- 4 layers101.6 × 53.3 mm

- 2 layers30.5 × 63 mm

Adbuino
akuker/adbuino
Arduino-based USB keyboard and Mouse to ADB adapter. Allows USB keyboards and mice to be used with vintage Macintosh computers.
75 parts60 - 2 layers86 × 54 mm

- 4 layers81.2 × 81.2 mm

- 2 layers89.3 × 55 mm

- 2 layers87.6 × 73.9 mm

PocketTRS
apuder/PocketTRS
PocketTRS uses a modern microcontroller to emulate a TRS-80 personal computer. It can be connected to any compatible VGA monitor and PS/2 keyboard. PocketTRS has TRS-IO embedded for full FreHD support.
45 parts38 - 4 layers315 × 147.2 mm

Questions
How big is the Midea WiFi Dongle PCB?
It measures 23 × 41 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Midea WiFi Dongle use?
20 parts, built around the AMS1117-3.3 and BSS138. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Midea WiFi Dongle KiCad files?
From the SaschaKP/midea-dongle repository on GitHub, at the commit this page was made from: the board is KiCad/Midea WiFi Dongle.kicad_pcb and its schematic KiCad/Midea WiFi Dongle.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Midea WiFi Dongle design in my own project?
Its repository states no licence, so its author keeps all rights: ask SaschaKP before reusing the design.