SpriteSAMD
KickSat Sprite (2019) running Circuitpython
- Size
- 47.2 × 35 mm
- Copper layers
- 2
- Thickness
- 0.6 mm
- Parts
- 68
- Nets
- 94
- Pads
- 263
- Tracks, vias
- 340, 107
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 7 Feb 2019
- Updated
- 18 Oct 2019
Overview
SpriteSAMD is an open-source printed circuit board by RoboticExplorationLab, from the RoboticExplorationLab/sprite repository on GitHub. It is a 2-layer board of 47.2 × 35 mm with 68 parts on 94 nets, routed with 340 tracks and 107 vias.
It is built around the TPS82740BSIPR, BAT-HLD-001 and HHM17139B2, with the LSM9DS1, RFM95W-915S2 and 10118194-0001LF among its other parts. Its parts include 30 connectors, 10 capacitors, 6 ICs, 5 resistors and 5 switches. It belongs with the SAM D and SAM boards of this library.
Main components
7TPS82740BSIPR
SIP-9-40℃~+85℃@(TA) 1 1.7MHz 2.2V~5.5V 2.6V~3.3V 200mA 360nA Buck Buck Built-in Fixed SIP-9 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersBAT-HLD-001
SMDSMD Button And Strip Battery Connector ROHSTE ConnectivityButton And Strip Battery ConnectorHHM17139B2
SMD-6P,0.8x1.6mmSMD-6P,0.8x1.6mm Balun ROHSTDKBalunLSM9DS1
LGA-24(3x3.5)-40℃~+85℃ 1.9V~3.6V 16bit Accelerometer Gyroscope SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps LGA-24(3x3.5) Accelerometers ROHSSTMicroelectronicsAccelerometersRFM95W-915S2
LCC-16_16X16mmLCC-16_16X16mm New Arrivals ROHSHopeRF Micro-electronicsUncategorised10118194-0001LF
SMD-30℃~+80℃ 1 100V 5P Black Female Micro-B USB 2.0 SMD USB Connectors ROHSAmphenolUSB ConnectorsRB550V-30
SOD-3231 Independent 1A 30V 30uA@10V 3A 560mV@1A SOD-323 Schottky Diodes ROHSCBISchottky Diodes
README
README.mdhardware: KiCad PCB files and bill of materials. Assembling a sprite? Check out https://roboticexplorationlab.github.io/sprite/ for an interactive BOM!
firmware: pre-built circuitpython bootloader.bin and firmware.uf2 (and the files to build it yourself)
software: circuitpython scripts and libraries working on the sprite
💡 Lots of applicable information also located on the PyCubed.org quickstart page.
Demos
Put all the files located in /software/ on to the sprite and start the serial console (as described above). After pressing Ctrl+C to halt the sprite, press any key to enter the REPL, then type
import NAMEOFFILEand press enter to execute the example. For example, it we wanted to run blink.py, it would be...
import blink- blink.py - will blink the green LED.
- i2c_IMU.py - samples all available sensors on the IMU and prints the results
- cursor.py - uses the X,Y data from the IMU accelerometer and moves the computer cursor accordingly
- cpc_test.py - example transmit message for the CC1101 radio
Parts
68| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | Conn_01x01 | custom-footprints:PinHeader_CUSTOM2 | J3, J4, J5, J6, J7, J8, J9, J10, J11, J12 |
| 8 | Conn_01x04 | custom-footprints:PinHeader_CUSTOM | J13, J14, J15, J16, J17, J18, J19, J20 |
| 7 | Conn_01x02 | custom-footprints:PinHeader_CUSTOM3 | J21, J22, J23, J24, J25, J26, J27 |
| 4 | 10K | Resistor_SMD:R_0402_1005Metric | R2, R3, R4, R5 |
| 4 | Conn_01x01 | custom-footprints:castellated_small_1side | J1, J28, J29, J30 |
| 4 | KXOB22-04X3F | custom-footprints:KXOB22-12X1F | S1, S2, S3, S4 |
| 3 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C1, C8, C10 |
| 3 | 10uF | Capacitor_SMD:C_0402_1005Metric | C2, C4, C7 |
| 3 | 1uF | Capacitor_SMD:C_0402_1005Metric | C3, C5, C6 |
| 2 | ANTENNA | Sprite:ANTENNA | ANT1, ANT2 |
| 1 | @HOLE0 | ||
| 1 | 10118194-0001LF | custom-footprints:10118194-0001LF | J2 |
| 1 | 10nF | Capacitor_SMD:C_0402_1005Metric | C9 |
| 1 | 10uH | Inductor_SMD:L_0805_2012Metric | L1 |
| 1 | 330 | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | ATSAMD51G_TQFN48 | ATSAMD51G19A-MU:QFN50P700X700X90-49N-D | U2 |
| 1 | BAT-HLD-001 | custom-footprints:BAT-HLD-001 | U3 |
| 1 | GREEN | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | HHM17139B2 | custom-footprints:balun0603 | U7 |
| 1 | KMR231NG LFS | Adafruit Feather M4 Express:BTN_KMR2_4.6X2.8 | SW1 |
| 1 | LSM9DS1 | Sprite:LGA24-8X4 | U1 |
| 1 | RB550V | Diode_SMD:D_SOD-323 | D2 |
| 1 | RFM95W-915S2 | RF_Module:HOPERF_RFM9XW_SMD | U8 |
| 1 | TPS82740BSIPR | custom-footprints:TPS82740ASIPR | U4 |
The 62 most common of 68 parts.
More from RoboticExplorationLab/sprite
1- 2 layers47.2 × 35 mm

Similar boards
- 4 layers44.4 × 35.8 mm

Avionics motherboard
spacecraft-design-lab-2019/avionics-motherboard
Main flight computer board for the PyCubed-1 spacecraft
76 parts - 4 layers100 × 100 mm

V25Panel
maholli/SAM32
Feather-sized SAMD51 with M4 core serving as UART bridge to WROOM ESP32
211 parts43 - 6 layers50 × 50 mm

- 6 layers57 × 25.9 mm

R7FS7MOD
Brazil-L/Lumeward-OpenSource
Open-source Lumeward firmware and development tools
228 parts2Apache-2.0 - 2 layers102.8 × 46.5 mm

METAL AIR BMS
MAATHES-THILAK-K/METAL_AIR_BMS
STM32-based Single Cell Metal-Air Battery Management System (BMS) featuring real-time voltage/current monitoring, temperature sensing, hydrogen gas detection, protection mechanisms, UART communication, and a…
88 parts - 2 layers127 × 257.8 mm

- 4 layers90.2 × 95.9 mm

- 2 layers83.5 × 66 mm

Open ed Rev.B
krikzz/open-ed
Open-ED is a very simple and cheap open source Genesis/Megadrive cartridge. The cartridge does not have its own processor or FPGA, it is built in the old school style using only memory and discrete logic.
82 parts169MIT
Questions
How big is the SpriteSAMD PCB?
It measures 47.2 × 35 mm and has 2 copper layers, 0.6 mm thick.
What parts does the SpriteSAMD use?
68 parts, built around the TPS82740BSIPR, BAT-HLD-001, HHM17139B2 and LSM9DS1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the SpriteSAMD KiCad files?
From the RoboticExplorationLab/sprite repository on GitHub, at the commit this page was made from: the board is hardware/sprite_v3/spriteSAMD.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the SpriteSAMD design in my own project?
Its repository states no licence, so its author keeps all rights: ask RoboticExplorationLab before reusing the design.