2 layers61 × 36.8 mm
2 layers66 × 66 mm
Shutter Driver
RiceAMO/HDD_Shutter_DriverHDD shutter driver circuit.
- Size
- 66 × 66 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 26
- Nets
- 24
- Pads
- 89
- Tracks, vias
- 105, 0
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 1 Dec 2017
- Updated
- 11 Feb 2018
Overview
Shutter Driver is an open-source printed circuit board by RiceAMO, from the RiceAMO/HDD_Shutter_Driver repository on GitHub, published under the MIT licence. It is a 2-layer board of 66 × 66 mm with 26 parts on 24 nets, routed with 105 tracks and 0 vias.
It is built around the IXDF604PI and LMD18200T. Its parts include 7 capacitors, 6 resistors, 4 connectors, 3 ICs and 3 diodes.
Main components
2README
README.mdHDD_Shutter_Driver
HDD shutter driver circuit based on Rob Scholten's 2007 RSI paper (see below). Modifications include the option of using an IXYS IXDF604PI (about $2/IC) instead of the TI LMD18200 (about $17/IC) to drive the shutter.
Notes
- Outputs are to standard BNC connectors so care should be taken to avoid shorting to ground.
- H3 (PWR_SEL) allows using a single voltage supply to power the IC and provide current for the shutter.
- H1 and H2 allow the selection of the output polarity (OUT_1x when using the IXDF604PI, OUT_2x when using LMD18200).
Ordering
Shutter Driver
The main circuit for driving HDD shutters.
Power Distribution
Circuit used to breakout a power supply for multiple shutter driver boards.
- v1.1: Add notes
- v1.0: Positive Power Distribution Rev. 1.0 (OSH Park)
Original paper
Enhanced laser shutter using a hard disk drive rotary voice-coil actuator
R. E. Scholten
Review of Scientific Instruments 78, 026101 (2007)
https://doi.org/10.1063/1.2437199
Also see
Parts
26| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 10nF | Capacitors_ThroughHole:C_Disc_D5.0mm_W2.5mm_P5.00mm | C3, C4 |
| 2 | D | Diodes_ThroughHole:D_DO-41_SOD81_P10.16mm_Horizontal | D2, D3 |
| 1 | 0.1uF | Capacitors_ThroughHole:C_Disc_D5.0mm_W2.5mm_P5.00mm | C2 |
| 1 | 10k | Resistors_ThroughHole:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R4 |
| 1 | 10uF | Capacitors_ThroughHole:CP_Radial_D5.0mm_P2.00mm | C6 |
| 1 | 2.7k | Resistors_ThroughHole:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R5 |
| 1 | 2500uF | Capacitors_ThroughHole:CP_Radial_D18.0mm_P7.50mm | C7 |
| 1 | 5.6V | Diodes_ThroughHole:D_DO-41_SOD81_P10.16mm_Horizontal | D1 |
| 1 | 6N139 | Housings_DIP:DIP-8_W7.62mm_Socket_LongPads | U1 |
| 1 | C | Capacitors_ThroughHole:CP_Radial_D18.0mm_P7.50mm | C5 |
| 1 | CP | Capacitors_ThroughHole:C_Disc_D5.0mm_W2.5mm_P5.00mm | C1 |
| 1 | IC_PWR | Sockets_MOLEX_KK-System:Socket_MOLEX-KK-RM2-54mm_Lock_2pin_straight | P1 |
| 1 | IXDF604PI | Housings_DIP:DIP-8_W7.62mm_Socket_LongPads | U2 |
| 1 | LMD18200 | TO_SOT_Packages_THT:Multiwatt_15_Vertical | U3 |
| 1 | PWR_SEL | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | H3 |
| 1 | R | Resistors_ThroughHole:R_Axial_Power_L25.0mm_W9.0mm_P30.48mm | R3 |
| 1 | R | Resistors_ThroughHole:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R6 |
| 1 | RI | Resistors_ThroughHole:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1 |
| 1 | RL | Resistors_ThroughHole:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2 |
| 1 | SEL_1 | Pin_Headers:Pin_Header_Straight_2x04_Pitch2.54mm | H1 |
| 1 | SEL_2 | Pin_Headers:Pin_Header_Straight_2x04_Pitch2.54mm | H2 |
| 1 | SHUTTER | Sockets_BNC:BNC_Socket_TYCO-AMP_LargePads | J2 |
| 1 | SHUTTER_PWR | Sockets_MOLEX_KK-System:Socket_MOLEX-KK-RM2-54mm_Lock_2pin_straight | P2 |
| 1 | TTL | Sockets_BNC:BNC_Socket_TYCO-AMP_LargePads | J1 |
More from RiceAMO/HDD_Shutter_Driver
1Similar boards
- 2 layers68.6 × 53.3 mm
Controller
Cemetech/TI-DCC
Direct z80 ASM DCC implementation for the TI-84 Plus C Silver Edition and similar calculators.
67 parts3BSD-3-Clause - 4 layers68.6 × 53.3 mm
Motor Shield v1
Pr0fiNoob/MopBot
MopBot ist ein experimenteller Bodenreinigungsroboter. Die Python-Software MopSlothOS läuft auf einem Raspberry Pi und übernimmt Navigation sowie die übergeordnete Steuerung.
30 parts3MIT - 2 layers70 × 100 mm
- 2 layers94 × 78.7 mm
Base rulante lmdv2
ClubRobotInsat/cartes
Toutes les cartes ici sont les cartes en développement au club. Vous pouvez retrouver dans les release les cartes correspondant à chaque robot.
27 partsApache-2.0 - 2 layers
H bridge 2018
ClubRobotInsat/h_bridge_2018
The H bridge PCB we use to power and control our DC motors
12 parts - 2 layers144.8 × 111.8 mm
- 4 layers70 × 70 mm
Tank
frangipp/TANK-PCB
Projet étudiant réalisé en binôme à l’ESEO Angers, ce TANK est un robot mobile à entraînement différentiel, piloté en Bluetooth via une application Android.
163 parts - 2 layers105 × 70 mm
Questions
How big is the Shutter Driver PCB?
It measures 66 × 66 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Shutter Driver use?
26 parts, built around the IXDF604PI and LMD18200T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Shutter Driver KiCad files?
From the RiceAMO/HDD_Shutter_Driver repository on GitHub, at the commit this page was made from: the board is Shutter_Driver/Shutter_Driver.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Shutter Driver design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).