

Pstwo2ascii
My rendition of Jim Brain/RETRO Innovations PS2Encoder
- Size
- 58.7 × 56.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 34
- Nets
- 58
- Pads
- 168
- Tracks, vias
- 351, 34
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 14 May 2025
- Updated
- 23 Jun 2025
Overview
Pstwo2ascii is an open-source printed circuit board by RetepV, from the RetepV/pstwo2ascii repository on GitHub. It is a 2-layer board of 58.7 × 56.2 mm with 34 parts on 58 nets, routed with 351 tracks and 34 vias.
It is built around the ATMEGA328-AU and MAX232N. Its parts include 10 capacitors, 7 connectors, 6 resistors, 3 switches and 2 ICs. It belongs with the retro computing and games boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
2README
README.mdpstwo2ascii
My rendition of Jim Brain/RETRO Innovations PS2Encoder.
The original (copyrighted by Jim Brain and RETRO Innovations) can be found here: https://github.com/go4retro/PS2Encoder.
I decided to make the board USB powered, and add a "real" RS-232 V24 interface. Most vintage computers cannot work with 0V/5V, but need positive and negative voltages. And some old vintage computers output +12V and -12V, and wil very likely blow up the ATMEGA's ports. Lastly, I used an ATMEGA328 instead of an ATMEGA88, just because I have a few of those lying around.
I decided to make it in SMD, to keep the boards small. I took hand-solderability into account as much as possible. Of course the connectors mostly dictate the final size of the board, and t.b.h. I think that if I had used PTH components, the board would not be much larger. But there you go: it's my design and I can do what I want to. ;)
Note: this is a WIP and has not been tested yet, prototypes have not even been created yet.
The base design and the software is not mine, but created and copyrighted (2008-2018) by Jim Brain / RETRO Innovations. I took the base design, redesigned it to make a full-fledged board powered by USB and having a real RS-232 V24 interface using a MAX232, and named it pstwo2ascii. This board is meant to be used with the firmware of PS2Encoder, which can be found here: https://github.com/go4retro/PS2Encoder/tree/master. Big thanks and kudos to Jim Brain for his work!
Please note that pstwo2ascii is covered under GPLv3, while PS2Encoder is covered under GPLv2. pstwo2ascii only applies to the hardware designs that you can find in this repository.
Licenses
PS2Encoder
Copyright Jim Brain and RETRO Innovations, 2008-2018
These files are free designs; you can redistribute them and/or modify them under the terms of the GNU General Public License, version 2 as published by the Free Software Foundation.
These files are distributed in the hope that they will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with these files; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
pstwo2ascii
Copyright Sporos Tech, Peter de Vroomen, 2025
pstwo2ascii is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.
pstwo2ascii is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with pstwo2ascii. If not, see https://www.gnu.org/licenses/.
Parts
34| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 1uF/16V | Capacitor_Tantalum_SMD:CP_EIA-3216-12_Kemet-S_Pad1.58x1.35mm_HandSolder | C6, C7, C8, C9, C10 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 10K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R5, R6 |
| 2 | 18pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4, C5 |
| 2 | 5.11K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 1 | 0.1u/10v | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A_Pad1.58x1.35mm_HandSolder | C2 |
| 1 | 1.8K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 1 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3 |
| 1 | 10u/10v | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A_Pad1.58x1.35mm_HandSolder | C1 |
| 1 | 8MHz | Crystal:Crystal_SMD_HC49-SD | Y1 |
| 1 | ASCII | Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_Vertical | J1 |
| 1 | ATmega328-AU | Package_QFP:TQFP-32_7x7mm_P0.8mm | U1 |
| 1 | CONFIG MODE | Sporos_Tech_Footprints:CL-SB-12B-0x SPDT switch | SW3 |
| 1 | Control | Connector_PinHeader_2.54mm:PinHeader_1x11_P2.54mm_Vertical | J5 |
| 1 | KBD MODE | Sporos_Tech_Footprints:CL-SB-12B-0x SPDT switch | SW2 |
| 1 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | MAX232 | Package_SO:SOIC-16_4.55x10.3mm_P1.27mm | U2 |
| 1 | PS2 | Custom_Footprints:Connector_Mini-DIN_Female_6Pin_2rows | J2 |
| 1 | RESET | Sporos_Tech_Footprints:SW_SPST_Omron_B3FS-100xP_4P | SW1 |
| 1 | RS232 v24 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | SPI | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J7 |
| 1 | USB-C Power | Sporos_Tech_Footprints:USB_C_Receptacle_Molex_213716-0001 | J6 |
| 1 | XT | Sporos_Tech_Footprints:DIN-5-180 | J3 |
Similar boards
- 2 layers88.4 × 34.2 mm

- 2 layers82 × 120 mm

Sample Numeric Keyboard
famichu/MagLev_Switch_MX
The 3D printable magnetic levitation contactless switch with the linear output hall effect sensor.
66 parts467 - 2 layers76.2 × 76.2 mm

PaperBack Converter
dqydj/PaperBack_EPaper_Display
Internet Connected or Standard Input EPaper Display
92 parts83MIT - 2 layers18 × 33.2 mm

Arduino pro mini
etimou/arduino-pro-mini-kicad
This is a clone of the well known arduino board "pro-mini" designed in kicad while the original was designed in eagle. Ref https://store.arduino.cc/arduino-pro-mini
23 parts69 - 2 layers101.6 × 147.3 mm

Karabas pro revER
andykarpov/karabas-pro
FPGA based retrocomputer with FDD and HDD controllers
223 parts37MIT - 4 layers100 × 100 mm

- 2 layers100 × 100 mm

- 2 layers100 × 70 mm

Questions
How big is the Pstwo2ascii PCB?
It measures 58.7 × 56.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Pstwo2ascii use?
34 parts, built around the ATMEGA328-AU and MAX232N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pstwo2ascii KiCad files?
From the RetepV/pstwo2ascii repository on GitHub, at the commit this page was made from: the board is pstwo2ascii.kicad_pcb and its schematic pstwo2ascii.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pstwo2ascii design in my own project?
Its repository states no licence, so its author keeps all rights: ask RetepV before reusing the design.