Skip to the content
2 layers40.6 × 109.3 mmENGR302, the printed circuit board in 3D

An in-class group project centered around developing a hobbyist rocket. This was developed by students in Group 6 from the ENGR301 & ENGR302 courses at the Victoria University of Wellington (NZ) in 2020.

Size
40.6 × 109.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
31
Nets
48
Pads
139
Tracks, vias
166, 0
Pours
4
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
19 Mar 2025
Updated
17 Sep 2025

Overview

ENGR302 is an open-source printed circuit board by RedHoodedWraith, from the RedHoodedWraith/Group6-Rocket-ENGR301-302 repository on GitHub. It is a 2-layer board of 40.6 × 109.3 mm with 31 parts on 48 nets, routed with 166 tracks and 0 vias.

It is built around the RFM98W-433S2. Its parts include 10 capacitors, 5 ICs, 3 resistors, 1 diode and 1 transistor. It belongs with the STM32 boards of this library.

Main components

1

README

README.md

Group 6's Rocket Project

Introduction

This project was developed as part of an in-class group project to design and develop a hobbyist rocket that used on-board programmable electronics to control it and to collect and report on-board telemetry.
It was developed in 2020 by students in Group 6 from the ENGR301 & ENGR302 courses at the Victoria University of Wellington in New Zealand.

While the students who worked on this project passed the aforementioned courses, at the time of writing, this project is in an unfinished state and there is not functioning rocket.
The courses, ENGR301 & ENGR302, were focused on developing our skills around working on technical projects as part of a development team that uses Agile Development Practices. In the context of the courses above, this project was worked on to put into practice what we had learnt and to demonstrate our skills relating to using Agile.

While this project is incomplete and isn't likely to be worked on, anyone is welcome to use what we have made so far and/or to finish it off.

Contributors

Software

  • Asami De Almeida
  • Ketaki Bagal
  • Penny Peneuta

Hardware

  • Jason McCormick
  • Sean Osborne-Curtis
  • Robert Reid
  • Dylan Sukha

University Staff Involved

  • Andre Geldenhuis
  • Aaron Chen

Modules:

Software Development

  • Sun Incinerator Rocket Controller | PID system
  • Sensor Test Programs
    • MPLI2C | Barometer + temperature readings.
    • MPU | | Gyro + Acceleartion readings, IMU+Servo Control.

Parts

31
QtyValueFootprintReferences
6CP1_SmallCapacitors_THT:CP_Radial_D4.0mm_P2.00mmC3, C5, C6, C7, C8, C10
3RResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR1, R2, R3
2CP1_SmallCapacitors_THT:C_Axial_L3.8mm_D2.6mm_P7.50mm_HorizontalC4, C9
2Motor_ServoConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalM1, M2
110k-100kResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR_pulldown1
12N7000Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalQ1
13.7VConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalBT2
17.4VConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalBT1
1Adafruit-STM32F405digikey-footprints:Adafruit_FeatherU3
1AntennaConnector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalAE1
1CCapacitors_THT:C_Axial_L5.1mm_D3.1mm_P10.00mm_HorizontalSuper_C1
1CCapacitors_THT:C_Axial_L3.8mm_D2.6mm_P10.00mm_HorizontalC1
1CP1Capacitors_THT:C_Axial_L3.8mm_D2.6mm_P10.00mm_HorizontalC2
1Conn_02x01Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ1
1DIODEdigikey-footprints:Diode_DO-35_P10mmD1
1GPS_ConnectorConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalU4
1LM317_3PinPackageConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalU5
1MPL3115a2_Boarddigikey-footprints:mpl3115a2U2
1MPU-6050-Boarddigikey-footprints:MPU_6050_BoardU1
1RFM98W-433S2RFM98W-433S2:XCVR_RFM98W-433S2TX1
1R_POT_TRIMConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalRV1
1SW_SPSTConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalSafetySwitch1

Similar boards

  • 4 layers35.1 × 77 mmEuroc controller, the printed circuit board in 3D

    Euroc controller

    aesirkth/fjalar_flight_controller

    A simpler flight controller

    94 parts1
  • 4 layers94.5 × 98.5 mmKraky, the printed circuit board in 3D

    Kraky

    thesh4dows/Kraky

    its a diy project of a device that emulates the flipper zero but using well available and cheap parts

    42 parts1GPL-3.0
  • 2 layers69 × 34.5 mmLora ch1, the printed circuit board in 3D

    Lora ch1

    0x000f1/lora-ch1

    This project is based on the ESP32 microcontroller that behaves like a bridge between mobile devices and the modules.

    37 parts
  • 2 layers55.6 × 55.5 mmCanSat, the printed circuit board in 3D

    CanSat

    ApolLO-CanSat/PCB

    Motherboard for the Team ApolLO's CanSat.

    86 parts
  • 2 layersPCB temp, the printed circuit board in 3D

    PCB temp

    ApolLO-CanSat/PCB-temp

    Repo for temporary PCB

    15 parts
  • 2 layers116.3 × 114.5 mmLora tracker V3, the printed circuit board in 3D

    Lora tracker V3

    bendelathouwer/asset-tracker

    diy asset tracker

    76 parts
  • 2 layers33 × 27.9 mmRfm69 breakout, the printed circuit board in 3D

    Rfm69 breakout

    jd-boyd/bts_ref_dev_adapter

    Example/test circuit of ams1117 chip meant to plug into space of 7505.

    5 parts

Questions

How big is the ENGR302 PCB?

It measures 40.6 × 109.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ENGR302 use?

31 parts, built around the RFM98W-433S2. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ENGR302 KiCad files?

From the RedHoodedWraith/Group6-Rocket-ENGR301-302 repository on GitHub, at the commit this page was made from: the board is Hardware_Development/KiCad/Circuit Development/Initial Project/ENGR302.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the ENGR302 design in my own project?

Its repository states no licence, so its author keeps all rights: ask RedHoodedWraith before reusing the design.