

Cobalt X Zero
Custom Gaming Mouse
- Size
- 45.1 × 74.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 49
- Nets
- 46
- Pads
- 170
- Tracks, vias
- 481, 109
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 20 Jul 2026
- Updated
- 30 Sep 2026
Overview
Cobalt X Zero is an open-source printed circuit board by RealSynarix, from the RealSynarix/Cobalt-X-Zero repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 45.1 × 74.3 mm with 49 parts on 46 nets, routed with 481 tracks and 109 vias.
It is built around the STM32G431KBT6, PMW3360DM-T2QU and AP2112K-3.3, with the EC10E1220501 among its other parts. Its parts include 17 resistors, 13 capacitors and 2 diodes. It belongs with the STM32 boards of this library.
Main components
4STM32G431KBT6
LQFP-32(7x7)-40℃~+85℃ 1.71V~3.6V 128KB 12bit 12bit 170MHz 26 32 Bit 32KB ARM Cortex-M4F Built-in FLASH LQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)PMW3360DM-T2QU
DIP-16Low-power mode、Interrupt output、Self-test function DIP-16 Specialized Sensors ROHSPixArtSpecialized SensorsAP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorisedEC10E1220501
插件插件 Rotary Encoders ROHSALPSALPINERotary Encoders
README
hardware/fabrication/pcb/README.mdPCB Fabrication
Files to manufacture and edit PCB.
| File | Purpose |
|---|---|
Cobalt-X_Zero.kicad_sch | Schematic |
Cobalt-X_Zero.kicad_pcb | Layout |
Cobalt-X_Zero_rev-3.zip | Gerbers |
Cobalt-X_Zero_rev-3_bom.csv | BOM |
positions.csv | Pick and place |
netlist.ipc | Netlist |
Order
Upload zip to fab, 4-layer 1.6mm ENIG if possible. Use BOM + positions for partial assembly. Switches and encoder better hand soldered.
Known issues rev 3
| Issue | Detail | Workaround |
|---|---|---|
| LED pins wrong | Pins swapped in schematic | Re-route or bend legs |
| Sensor noise | SI/EMI near sensor | Firmware filters most, fix would be better grounding and 3.3V routing |
Works as-is.
Parts
49| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100nF | Capacitor_SMD:C_0603_1608Metric | C7, C8, C11, C12, C14, C20 |
| 6 | 150 | Resistor_SMD:R_0603_1608Metric | R12, R13, R14, R15, R16, R17 |
| 6 | SW_Push | Buttons:SW_PUSH_6mm_H7.3mm_2-Pin | DFU1, LMB1, MACRO1, MACRO2, MMB1, RMB1 |
| 5 | TestPoint_Probe | TestPoint:TestPoint_Pad_D1.0mm | 3.3V, GND, PA15, SWC, SWD |
| 4 | 1uF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C9, C10 |
| 4 | 33 | Resistor_SMD:R_0603_1608Metric | R8, R9, R10, R11 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric | R4, R5, R6 |
| 2 | 10nF | Capacitor_SMD:C_0603_1608Metric | C3, C17 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R2, R3 |
| 2 | LED_RGBA | LED_THT:LED_D5.0mm-4_RGB | LED1, LED2 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 39 | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C13 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | REG1 |
| 1 | EC10E1220501 | Scroll:TRIM_EC10E1220501 | WHEEL1 |
| 1 | PMW3360DM-T2QU | Sensor_Mouse:PMW3360 | SENSOR1 |
| 1 | STM32G431KBT6 | Package_QFP:LQFP-32_7x7mm_P0.8mm | MCU1 |
| 1 | TLV75519PDBVR | 1.9v REGULATOR:DBV0005A_N | REG2 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | USB1 |
Similar boards
- 2 layers34 × 107.5 mm

- 4 layers76 × 56 mm

- 2 layers58 × 49.5 mm

Gary the mouse
Small-doge128/Gary-the-mouse
A custom mouse with TTC wheel encoder (8mm), lipo battery 1 200mAh, 4x kailh gm 8.0 micro switch and seeed studio nrf52840 all on my custom pcb, but sensor PAW3395 LM19 on badjeffs pcb.
11 parts1 - 4 layers

- 2 layers57.2 × 78.7 mm

Mouse Micro
jacksterb1234/Mouse-Micro
A fully custom gaming mouse built from scratch — from clay hand modeling and photogrammetry all the way to a custom KiCad PCB.
22 parts - 2 layers138.8 × 96.4 mm

- 4 layers68 × 40 mm

- 4 layers88.1 × 59.4 mm

Chromapi motherboard v1
Mowibox/chromapi_motherboard
Raspberry Pi control HAT dedicated to the quadruped robot Chromapi.
139 parts2Apache-2.0
Questions
How big is the Cobalt X Zero PCB?
It measures 45.1 × 74.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Cobalt X Zero use?
49 parts, built around the STM32G431KBT6, PMW3360DM-T2QU, AP2112K-3.3 and EC10E1220501. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Cobalt X Zero KiCad files?
From the RealSynarix/Cobalt-X-Zero repository on GitHub, at the commit this page was made from: the board is hardware/fabrication/pcb/Cobalt-X_Zero.kicad_pcb and its schematic hardware/fabrication/pcb/Cobalt-X_Zero.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Cobalt X Zero design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).