
Ventilator
RespiraWorks/Ventilator
Fully-featured ICU ventilator design, optimized for manufacture using commonly available components and free to license.

A RPi4/ RPico based synchronised multi oven controller with an optional ATTiny based power stage
Ssr pcb is an open-source printed circuit board by Pharmaceutical-Analysis, from the Pharmaceutical-Analysis/Rpi-GC-Oven-Controller repository on GitHub. It is a 2-layer board of 120 × 100 mm with 62 parts on 45 nets, routed with 378 tracks and 445 vias.
It is built around the ATTINY841-SSU, MMBT3904 and 1N4448W, with the KSC341GLFS and MOC3052M among its other parts. Its parts include 18 resistors, 10 capacitors, 9 connectors, 7 diodes and 3 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
#License Copyright (C) 2026 <Kris Wolfs/ KU Leuven Farmaceutische Analyse>
SPDX-License-Identifier: CERN-OHL-P-2.0+
This source describes Open Hardware and is licensed under CERN Open Hardware Licence - Permissive v2 or later (CERN-OHL-P v2+).CERN Open Hardware Licence v2 - Permissive or later (CERN-OHL-P-2.0+).
You may redistribute and modify this source and make products using it under the terms of the CERN-OHL-P v2+ (see LICENSE-HARDWARE).
This source is distributed WITHOUT ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING OF MERCHANTABILITY, SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE. Please see the CERN-OHL-P v2+ for further details.
This document provides an overview of the key components and connectors on the PCB that interfaces with the ATtiny841 for power and communication control.

Located on the left side of the PCB, the ATtiny841 microcontroller is the core of the control system.
Used when the ATtiny operates as a Solid State Relay (SSR) controller. Accepts an external control signal.
A physical switch to select between I²C or SPI communication mode for the ATtiny.
A safety input, typically used to detect whether a door is open or closed.
Located at the top-left of the schematic. Provides electrical isolation between the control circuit and the high-voltage power section.
Located in the center of the schematic. When a zero-crossing event occurs, pin PB1 of the ATtiny goes LOW, triggering synchronization for power control (e.g., phase control or PWM).
Positioned on the right side of the PCB, this IC is used to measure the current flowing through the load, useful for monitoring and feedback.
Located at the top-right, this is the output connector for the triac, which switches the power to the load.
The reset pin of the ATtiny841 is made accessible externally via S1, allowing the microcontroller to be manually reset without reprogramming or power-cycling the entire system.

Ensure the correct position of SW1 before powering the device to match the intended communication protocol.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10k | proj_footprint:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1, R4, R5, R7, R13, R19*1 |
| 5 | 1N4148 | proj_footprint:D_SOD-123 | D2, D3, D4, D5, D6 |
| 4 | MountingHole | proj_footprint:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 2 | 100n | proj_footprint:C_1812_4532Metric_Pad1.57x3.40mm_HandSolder | C2, C10 |
| 2 | 1k | proj_footprint:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R3, R12 |
| 2 | 1n | proj_footprint:C_1812_4532Metric_Pad1.57x3.40mm_HandSolder | C7, C9 |
| 2 | 220k | proj_footprint:R_2512_6332Metric_Pad1.40x3.35mm_HandSolder | R16, R17 |
| 2 | 4.7k | proj_footprint:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | 0k1, R9 |
| 2 | 80uH | proj_footprint:SN14P-300J | L1, L2 |
| 2 | MMBT3904 | proj_footprint:SOT-23 | Q1, Q2 |
| 1 | 100nF 400V | proj_footprint:C_2220_5750 _1.97x5.40mm_HandSolder | C6 |
| 1 | 10u | proj_footprint:CP_Elec_5x5.8 | C5 |
| 1 | 1N4448W | proj_footprint:D_SOD-123 | D7 |
| 1 | 1u | proj_footprint:C_1812_4532Metric_Pad1.57x3.40mm_HandSolder | C1 |
| 1 | 1µf | proj_footprint:C_1812_4532Metric_Pad1.57x3.40mm_HandSolder | C8 |
| 1 | 200 | proj_footprint:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R2 |
| 1 | 220 | proj_footprint:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R6 |
| 1 | 240V/110V AC | proj_footprint:PHOENIX_1703083 | J7 |
| 1 | 2k | proj_footprint:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R18 |
| 1 | 360R | proj_footprint:R_2010_5025Metric_Pad1.40x2.65mm_HandSolder | R8 |
| 1 | 39 | proj_footprint:R_2010_5025Metric_Pad1.40x2.65mm_HandSolder | R11 |
| 1 | 470R | proj_footprint:R_2010_5025Metric_Pad1.40x2.65mm_HandSolder | R10 |
| 1 | 47k | proj_footprint:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R14 |
| 1 | 47nF 400V | proj_footprint:C_2220_5750 _1.97x5.40mm_HandSolder | C3 |
| 1 | 4N35 | proj_footprint:4N35S | U1 |
| 1 | 5.6nF 400V | proj_footprint:C_2220_5750 _1.97x5.40mm_HandSolder | C4 |
| 1 | 510k | proj_footprint:R_2010_5025Metric_Pad1.40x2.65mm_HandSolder | R15 |
| 1 | ACS712xLCTR-20A | proj_footprint:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | ATTINY841-SSU | proj_footprint:SOIC-14_3.9x8.7mm_P1.27mm | IC1 |
| 1 | AVR-ISP-6 | proj_footprint:Molex_KK-254_AE-6410-06A_1x06_P2.54mm_Vertical | J3 |
| 1 | Door switch | proj_footprint:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J1 |
| 1 | FUSE | proj_footprint:3132874 | F1 |
| 1 | I2C-4 | proj_footprint:Molex_KK-254_AE-6410-06A_1x06_P2.54mm_Vertical | J4 |
| 1 | I2C-4 | proj_footprint:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_Vertical | J5 |
| 1 | KSC341GLFS | proj_footprint:KSC341GLFS | S1 |
| 1 | LED | proj_footprint:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | LOAD | proj_footprint:PHOENIX_1703083 | J8 |
| 1 | MOC-3052 | proj_footprint:SOP254P916X508-6N | USM1 |
| 1 | SSR | proj_footprint:Molex_KK-254_AE-6410-03A_1x03_P2.54mm_Vertical | J2 |
| 1 | Thermal Switch | proj_footprint:PHOENIX_1703083 | J9 |
| 1 | Triac | proj_footprint:PHOENIX_1703084 | J6 |
| 1 | VR | proj_footprint:MOV14D621K | VR1 |
| 1 | spi/i2c | proj_footprint:SW_A6S-1104-H_OMR | SW1 |

RespiraWorks/Ventilator
Fully-featured ICU ventilator design, optimized for manufacture using commonly available components and free to license.

jerryok826/rover-monitor
Rover monitor is a simple info center for the JPL open-source-rover project


Miceuz/triac-bloc
An universal power block based on triac. In essence this is a solid state relay with some bells and whistles




marcass/furnace_control
Control a FUWI pellet boiler with arduino to improve smarts
It measures 120 × 100 mm and has 2 copper layers, 1.6 mm thick.
62 parts, built around the ATTINY841-SSU, MMBT3904, 1N4448W and KSC341GLFS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Pharmaceutical-Analysis/Rpi-GC-Oven-Controller repository on GitHub, at the commit this page was made from: the board is Hardware/ssr_pcb.kicad_pcb and its schematic Hardware/ssr_pcb.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Pharmaceutical-Analysis before reusing the design.