4 layers70 × 157.5 mm
Controller Tv Lift
vyrubaev/TV-Lift-Controller
TVLift Controller is an intelligent controller for TV lift and lower mechanisms, based on the ESP32 microcontroller.
103 parts
2 layers80 × 60 mm
Esp32-clima
Ontos-2021/esp32-climaEstación meteorológica local con ESP32-WROOM-32, BMP180 y DHT22.
- Size
- 80 × 60 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 30
- Nets
- 16
- Pads
- 149
- Tracks, vias
- 280, 52
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 1 Jun 2026
- Updated
- 1 Jun 2026
Overview
Esp32-clima is an open-source printed circuit board by Ontos-2021, from the Ontos-2021/esp32-clima repository on GitHub. It is a 2-layer board of 80 × 60 mm with 30 parts on 16 nets, routed with 280 tracks and 52 vias.
It is built around the CP2102N-EK, ESP32-WROOM-32 and LM2596S-5.0, with the AMS1117-3.3 and SS34 among its other parts. Its parts include 11 capacitors, 6 resistors, 4 ICs, 4 connectors and 2 diodes. It belongs with the ESP32 and RISC-V boards of this library.
Main components
5CP2102N-EK
-- USB Conversion Modules ROHSSilicon LabsUSB Conversion Modules
ESP32-WROOM-32
SMD,18x25.5mm-40℃~+85℃ -98dBm 2.4GHz 2.7V~3.6V 20dBm Bluetooth4.2 ESP32-DOWDQ6 UART、SDIO、SPI、I2C、GPIO、PWM、ADC、DAC SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi Modules
LM2596S-5.0
TO-263-5-40℃~+125℃@(TJ) 1 150kHz 3A 4.5V~40V 5V 5mA Buck Buck Built-in Fixed No TO-263-5 DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
SS34
SMA(DO-214AC)-55℃~+125℃ 3A 40V 500uA@40V 550mV@3A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
README
README.mdESP32 Clima
Estación meteorológica local con ESP32-WROOM-32, BMP180 y DHT22.
Componentes principales
| Componente | Descripción |
|---|---|
| ESP32-WROOM-32 | Microcontrolador con WiFi |
| BMP180 | Sensor de presión barométrica y temperatura |
| DHT22 / AM2302 | Sensor de humedad y temperatura |
| CP2102N | USB-UART para programación |
| LM2596S-5.0 | Regulador 12V → 5V |
| AMS1117-3.3 | Regulador 5V → 3.3V |
Repositorio
esp32-clima/
├── hardware/ # Diseño PCB (KiCad + Gerbers)
├── firmware/ # Código ESP32 (PlatformIO, Arduino)
├── enclosure/ # Diseño 3D de la caja (Blender, STL)
├── README.md
└── .gitignorePCB
PCB de doble cara 80×60 mm, diseñada en KiCad 9.
- Schematic:
hardware/esp32_clima.kicad_sch - Layout:
hardware/esp32_clima.kicad_pcb - Fabricación:
hardware/fabrication/(Gerbers, BOM, positions, ZIP para PCBWay)
Firmware
Crea un punto de acceso WiFi ESP32-CLIMA (192.168.4.1) con interfaz web.
Cargar
cd firmware
pio run --target upload
pio device monitorLibrerías (PlatformIO)
- Adafruit BMP085 Library
- DHT sensor library
- Adafruit Unified Sensor
Enclosure
Caja impresa 3D diseñada en Blender, incluida como STL y .blend.
Licencia
MIT
Parts
30| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100nF | esp32_clima:C_0603_1608Metric | C1, C3, C7, C9 |
| 4 | 10uF | esp32_clima:CP_Elec_5x5.3 | C2, C5, C6, C8 |
| 3 | 10k | esp32_clima:R_0603_1608Metric | R3, R5, R6 |
| 2 | 4.7k | esp32_clima:R_0603_1608Metric | R1, R2 |
| 1 | 100nF | Capacitor_SMD:C_0603_1608Metric | C11 |
| 1 | 1uF | esp32_clima:C_0603_1608Metric | C10 |
| 1 | 220uF | esp32_clima:CP_Elec_8x10 | C4 |
| 1 | 330 | esp32_clima:R_0603_1608Metric | R4 |
| 1 | 33uH | esp32_clima:L_10.4x10.4_H4.8 | L1 |
| 1 | AMS1117-3.3 | esp32_clima:SOT-223-3_TabPin2 | U2 |
| 1 | BMP180_Header | esp32_clima:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | BOOT | esp32_clima:SW_SPST_Compact | SW2 |
| 1 | Barrel_Jack_12V | esp32_clima:BarrelJack_CUI_PJ-102AH_Horizontal | J1 |
| 1 | CP2102N | QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm_ThermalVias | U3 |
| 1 | DHT22_Header | esp32_clima:PinHeader_1x03_P2.54mm_Vertical | J3 |
| 1 | EN_RESET | esp32_clima:SW_SPST_Compact | SW1 |
| 1 | ESP32-WROOM-32 | esp32_clima:ESP32-WROOM-32 | U1 |
| 1 | LED | esp32_clima:LED_0603_1608Metric | LED1 |
| 1 | LM2596S-5.0 | esp32_clima:TO-263-5_TabPin3 | U4 |
| 1 | SS34 | esp32_clima:D_SMB | D1 |
| 1 | USB-C_Receptacle | esp32_clima:USB-C-2P0-Compact | J4 |
Similar boards
- 2 layers54 × 68 mm
OpenSTM32F4 LQFP64
phonght32/openSTM32F4_LQFP64
openSTM32 board using STM32F4 LQFP64 package. This board designed to perform base control for SLAM and Navigation.There are also many availabe connectors that meet many other application requirements.
77 parts7MIT - 2 layers102 × 66 mm
FREE ENERGY ESP
Sureshbkmr/Energy-Harvesting-Based-on-Beaden-Research-Paper
Based on Beaden Research Paper full custom PCB
60 parts - 2 layers67 × 104 mm
Breakout board
Mritunjay5511/ESP32-Multi-Motor-Controller-Board-
Custom ESP32-WROOM-32 robotics controller PCB with onboard buck/LDO power regulation, auto-program circuit, and BTS7960/RMCS/relay/servo interfaces. Designed in KiCad.
38 parts5MIT - 2 layers81.3 × 86.4 mm
Water Dispenser
anadskman/Water-Dispenser
A water dispenser that can dispense water mixed with flavouring like blackcurrent
18 parts1 - 2 layers80 × 140.5 mm
- 4 layers203.8 × 99.1 mm
ISOpower complete bothboards
practable/iso-power-pcb
Remote power control board for ISO experiment containers, used for remote labs projects
196 partsGPL-3.0 - 2 layers100 × 68 mm
Questions
How big is the Esp32-clima PCB?
It measures 80 × 60 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Esp32-clima use?
30 parts, built around the CP2102N-EK, ESP32-WROOM-32, LM2596S-5.0 and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Esp32-clima KiCad files?
From the Ontos-2021/esp32-clima repository on GitHub, at the commit this page was made from: the board is hardware/esp32_clima.kicad_pcb and its schematic hardware/esp32_clima.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Esp32-clima design in my own project?
Its repository states no licence, so its author keeps all rights: ask Ontos-2021 before reusing the design.