4 layers119.4 × 99.1 mm
ISOpower
practable/iso-power-pcb
Remote power control board for ISO experiment containers, used for remote labs projects
159 partsGPL-3.0
4 layers203.8 × 99.1 mm
ISOpower complete bothboards
practable/iso-power-pcbRemote power control board for ISO experiment containers, used for remote labs projects
- Size
- 203.8 × 99.1 mm
- Copper layers
- 4
- Thickness
- 4.69 mm
- Parts
- 196
- Nets
- 193
- Pads
- 678
- Tracks, vias
- 1,665, 312
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 24 Jan 2022
- Updated
- 25 Jul 2025
Overview
ISOpower complete bothboards is an open-source printed circuit board by practable, from the practable/iso-power-pcb repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 203.8 × 99.1 mm with 196 parts on 193 nets, routed with 1,665 tracks and 312 vias.
It is built around the ATMEGA328PB-MN, CH340C and ESP32-WROOM-32, with the LM2596S-5.0, AMS1117-3.3 and HEF4093BT among its other parts. Its parts include 47 resistors, 30 capacitors, 21 connectors, 20 transistors and 15 ICs. It belongs with the ESP32, AVR (ATmega, ATtiny) and RISC-V boards of this library.
Main components
10
ATMEGA328PB-MN
QFN-32-EP(5x5)-40℃~+105℃ 1.8V~5.5V 10bit 1KB 20MHz 27 2KB 32KB 8 Bit AVR Built-in FLASH QFN-32-EP(5x5) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
CH340C
SOP-16-20℃~+70℃ 2Mbps 3.3V、5V 50uA 7mA Transceiver USB 2.0 SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB Converters
ESP32-WROOM-32
SMD,18x25.5mm-40℃~+85℃ -98dBm 2.4GHz 2.7V~3.6V 20dBm Bluetooth4.2 ESP32-DOWDQ6 UART、SDIO、SPI、I2C、GPIO、PWM、ADC、DAC SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi Modules
LM2596S-5.0
TO-263-5-40℃~+125℃@(TJ) 1 150kHz 3A 4.5V~40V 5V 5mA Buck Buck Built-in Fixed No TO-263-5 DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
HEF4093BT
SO-14-40℃~+125℃ 1uA 3.4mA 3.4mA 3.5V~11V 3V~15V 4 4000B Series 60ns@15V,50pF NAND Gate SOIC-14 Logic Gates ROHSNexperiaLogic Gates
BC817
SOT-231 NPN 100nA 150MHz 300mW 40 45V 500mA 5V 700mV NPN SOT-23 Bipolar (BJT) ROHSShikuesBipolar (BJT)
IRF5305PBF
TO-220AB-55℃~+175℃ 1 P-Channel 1.2nF 110W 31A 4V 55V 60mΩ@10V 63nC@10V P-Channel TO-220AB MOSFETs ROHSInfineon TechnologiesMOSFETsSI2319CDS
SOT-23-55℃~+150℃ 1 P-Channel 108mΩ@4.5V 2.5V 2.5W 21nC@10V 4.4A 40V 595pF 61pF 76pF P-Channel SOT-23 MOSFETs ROHSVishay IntertechnologyMOSFETs
BZV55B18
-Zener DiodesTaiwan Semiconductor
README
README.mdISOpowerProject
Remote power control board for ISO experiment containers, used for remote labs projects
Use
Programming [See Issues]
To Program AtMega328pb use the following settings:
prog_power_select
- Jumper is used for power routing during programming
- Cut trace to main and solder USB to center to enable USB power during programming.
- Ensure to remove USB side and replace main for normal use
Issues V1.0
- Tx & Rx Pin swapped on CH340 - aTmeGA328P
- To enable USB communication, reverse pins 2 & 3
Parts
196| Qty | Value | Footprint | References |
|---|---|---|---|
| 26 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22, R23, R24 +10 |
| 18 | 100n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C3, C4, C11, C12, C15, C16, C22, C23, C24, C26, C27, C28, C29, C30 +2 |
| 12 | BC817 | Package_TO_SOT_SMD:SOT-23 | Q9, Q10, Q11, Q12, Q13, Q14, Q15, Q16, Q17, Q18, Q19, Q20 |
| 6 | 220r | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R27, R28, R31, R32, R33, R34 |
| 6 | IRF5305_PBF | Package_TO_SOT_SMD:TO-263-2 | Q1, Q4, Q5, Q6, Q7, Q8 |
| 6 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H5, H6, H7, H8, H9, H10 |
| 5 | Net_Tie | NetTie:NetTie-2_SMD_Pad0.5mm | N3, N5, N7, N9, N10 |
| 5 | USB_CH_A | Connector_USB:USB_A_Molex_67643_Horizontal | J9, J10, J11, J12, J13 |
| 5 | XT30_connector_DC_30A_female | Connector_AMASS:AMASS_XT30PW-F_1x02_P2.50mm_Horizontal | J14, J15, J16, J17, J18 |
| 4 | 560r | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1a1, R2b1, R3a1, R3b1 |
| 4 | TL431DBZ | Package_TO_SOT_SMD:SOT-23 | U15, U16, U17, U18 |
| 3 | 100u | Capacitor_SMD:CP_Elec_6.3x7.7 | C9, C10, C21 |
| 3 | 330r | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R4, R30 |
| 2 | 1n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C17, C18 |
| 2 | 22p | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C7, C8 |
| 2 | 22u | Capacitor_SMD:CP_Elec_6.3x5.4 | C13, C14 |
| 2 | 470r | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1b1, R4b1 |
| 2 | ACS712xLCTR-30A | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U6, U7 |
| 2 | Blue | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2, D9 |
| 2 | CH340C | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U8, U14 |
| 2 | GREEN | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D5, D6 |
| 2 | RED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D7, D8 |
| 2 | Si2319CDS | Package_TO_SOT_SMD:SOT-23 | Q2, Q3 |
| 2 | USB_B_Mini | Connector_USB:USB_Mini-B_Lumberg_2486_01_Horizontal | J20, J31 |
| 2 | i6A4W020A-DC-DC-250W | ISOpower:i6A4W-DIP | U4, U5 |
| 1 | 10uH | Inductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | L1 |
| 1 | 12V_BUS | TestPoint:TestPoint_Pad_D1.5mm | TP4 |
| 1 | 12V_MONITOR | TestPoint:TestPoint_Pad_D1.5mm | TP9 |
| 1 | 12vTerminal | TerminalBlock:TerminalBlock_Altech_AK300-2_P5.00mm | J22 |
| 1 | 12v_trim | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R7 |
| 1 | 16MHz | Crystal:Crystal_SMD_Abracon_ABM3C-4Pin_5.0x3.2mm | Y1 |
| 1 | 1M | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8 |
| 1 | 1N5821 | Diode_SMD:D_SMA | D3 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R29 |
| 1 | 20A | Fuse:Fuseholder_Cylinder-5x20mm_Stelvio-Kontek_PTF78_Horizontal_Open | F1 |
| 1 | 220u | Capacitor_SMD:CP_Elec_6.3x7.7 | C20 |
| 1 | 24V_BUS | TestPoint:TestPoint_Pad_D1.5mm | TP2 |
| 1 | 24vTerminal | TerminalBlock:TerminalBlock_Altech_AK300-2_P5.00mm | J21 |
| 1 | 2k0 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4a1 |
| 1 | 2k2 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2a1 |
| 1 | 2x2_ISOpower_mountingHoles | MountingHole:ISOpower_4xmounting_M3 | H11 |
| 1 | 33uH | Inductor_SMD:L_12x12mm_H8mm | L2 |
| 1 | 3V3_BUS | TestPoint:TestPoint_Pad_D1.5mm | TP3 |
| 1 | 3V3_spare | Connector_PinHeader_1.27mm:PinHeader_1x01_P1.27mm_Vertical | J30 |
| 1 | 4n7 | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C25 |
| 1 | 5V_BUS | TestPoint:TestPoint_Pad_D1.5mm | TP5 |
| 1 | 5V_MONITOR | TestPoint:TestPoint_Pad_D1.5mm | TP10 |
| 1 | 5vTerminal | TerminalBlock:TerminalBlock_Altech_AK300-2_P5.00mm | J23 |
| 1 | 5v_trim | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R6 |
| 1 | 680u | Capacitor_THT:C_Radial_D12.5mm_H20.0mm_P5.00mm | C19 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | ATmega328PB-M | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm | U3 |
| 1 | AVR-ISP | Connector_PinHeader_1.27mm:PinHeader_2x03_P1.27mm_Vertical | J8 |
| 1 | AtMega_Reset | TestPoint:TestPoint_Pad_D1.5mm | TP6 |
| 1 | BOOT | Button_Switch_SMD:SW_SPST_EVQPE1 | SW2 |
| 1 | BZV55B18 | Diode_SMD:D_MiniMELF_Handsoldering | D1 |
| 1 | DSBL_BYPSS_A | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP3 |
| 1 | DSBL_BYPSS_B | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP2 |
| 1 | EN | Button_Switch_SMD:SW_SPST_EVQPE1 | SW3 |
| 1 | ESP32-WROOM-32 | RF_Module:ESP32-WROOM-32 | U1 |
| 1 | ESP32_header | Connector_PinHeader_1.27mm:PinHeader_1x10_P1.27mm_Vertical | J19 |
| 1 | ESP_GPIO_A | Connector_PinHeader_1.27mm:PinHeader_1x10_P1.27mm_Vertical | J5 |
| 1 | ESP_GPIO_B | Connector_PinHeader_1.27mm:PinHeader_1x05_P1.27mm_Vertical | J2 |
| 1 | ESPpin4-7 | Connector_PinHeader_1.27mm:PinHeader_1x04_P1.27mm_Vertical | J3 |
| 1 | Fan_IEC60617 | ISOpower:Fan12V_40by10.5mm | M1 |
| 1 | GND | TestPoint:TestPoint_Pad_D1.5mm | TP1 |
| 1 | HEF4093B | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U19 |
| 1 | LM2596S-5 | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U10 |
| 1 | LOGO | 000_Graphics_Immo:practactable.io_text_30x11_SM | G*** |
| 1 | LOGO | 000_Graphics_Immo:practactable.io_text_50x20 | G*** |
| 1 | LOGO | 000_Graphics_Immo:practactable.io_text_20x8 | G*** |
| 1 | LOGO | 000_Graphics_Immo:practactable.io_symbol_7x6 | G*** |
| 1 | MCU_PWR | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabels | JP1 |
| 1 | Net_Tie | NetTie:NetTie-8-15A_1oz_2oz_long | N8 |
| 1 | Net_Tie | NetTie:NetTie-8-15A_1oz_2oz | N6 |
| 1 | OP_0 | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP4 |
| 1 | OP_1 | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP5 |
| 1 | OP_2 | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP6 |
| 1 | OP_3 | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP7 |
| 1 | OP_4 | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP8 |
The 182 most common of 196 parts.
More from practable/iso-power-pcb
3- 4 layers119.4 × 99.1 mm
ISOpower
practable/iso-power-pcb
Remote power control board for ISO experiment containers, used for remote labs projects
130 partsGPL-3.0 - 4 layers52.1 × 35.6 mm
ISOpowerWiFi PCB
practable/iso-power-pcb
Remote power control board for ISO experiment containers, used for remote labs projects
38 partsGPL-3.0
Similar boards
- 2 layers93.4 × 87.4 mm
- 2 layers67 × 104 mm
Breakout board
Mritunjay5511/ESP32-Multi-Motor-Controller-Board-
Custom ESP32-WROOM-32 robotics controller PCB with onboard buck/LDO power regulation, auto-program circuit, and BTS7960/RMCS/relay/servo interfaces. Designed in KiCad.
38 parts5MIT - 4 layers85.1 × 53.3 mm
- 2 layers80 × 42.2 mm
Res Meas
ntd176/res-meas-pcb
Measurement: Unbalanced wheatstone bridge with ads1115 (16-bit ADC)
32 partsMIT - 2 layers115 × 115 mm
- 2 layers78.5 × 34.3 mm
- 2 layers65 × 56 mm
- 2 layers54.5 × 29.5 mm
Questions
How big is the ISOpower complete bothboards PCB?
It measures 203.8 × 99.1 mm and has 4 copper layers, 4.69 mm thick.
What parts does the ISOpower complete bothboards use?
196 parts, built around the ATMEGA328PB-MN, CH340C, ESP32-WROOM-32 and LM2596S-5.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ISOpower complete bothboards KiCad files?
From the practable/iso-power-pcb repository on GitHub, at the commit this page was made from: the board is Backup/ISOpower_complete_bothboards/ISOpower_complete_bothboards.kicad_pcb and its schematic Backup/ISOpower_complete_bothboards/5to12_logic.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ISOpower complete bothboards design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).