Skip to the content
2 layers80 × 80 mmProject Zeta, the printed circuit board in 3D

Project Zeta

Size
80 × 80 mm
Copper layers
2
Thickness
1.6 mm
Parts
28
Nets
39
Pads
100
Tracks, vias
163, 46
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
10 Oct 2026
Updated
3 Nov 2026

Overview

Project Zeta is an open-source printed circuit board by OatMealXXII, from the OatMealXXII/Project_Zeta repository on GitHub, published under the MIT licence. It is a 2-layer board of 80 × 80 mm with 28 parts on 39 nets, routed with 163 tracks and 46 vias.

It is built around the SMAJ5.0A and SS14. Its parts include 8 connectors, 4 capacitors, 4 diodes and 2 fuses.

Main components

2

README

README.md

IoT Carrier Board for Raspberry Pi Pico 2 / 2W (Project Zeta) - Rev 1.1

A rugged, modular IoT carrier board designed for Raspberry Pi Pico 2 and Pico 2W microcontrollers deployed in harsh outdoor, telemetry, and edge-computing environments. This board integrates primary surge protection, reverse-polarity defense, isolated grounding, and sensor interface expansion.


Architecture & Design Highlights

  • Modular Carrier Architecture: Separates power handling, field protection, and physical wiring from the core logic board, enabling hot-swap servicing and low maintenance overhead.
  • Hardware-First Resilience (KISS Principle): Built entirely with robust discrete semiconductors and passive protection networks, eliminating fragile active supervisory ICs and maintaining zero quiescent current drain.
  • Sub-Layer High-Energy Routing: High-current surge paths and gas discharge loops are isolated on the bottom layer to eliminate transient EMI coupling into sensitive microcontroller logic.
  • Dual-Domain Ground Separation: Features a dedicated *Earth ⏚ path isolated from logic/signal GND, specifically routed to safely divert atmospheric lightning surges and external ESD directly into structural grounding.

Power & Surge Protection Subsystem

text
[External Surge / Lightning ESD]
│
▼
[GDT (GD1)] ────────────────────────► *Earth ⏚ (Chassis / Field Ground)
│
[DC Input / 1S Li-ion Battery]                  │ (Isolated Domain)
│                                   ▼
▼                              [Earth Rod]
[SS14 Schottky (D1)] ───► (Reverse-Polarity Protection)
│
├───────────────► [TVS Diode (D2)] ──► Signal GND (Overvoltage Clamping)
│
├───────────────► [100µF Bulk Cap]  ──► Signal GND (Inrush & Transient Reservoir)
├───────────────► [100nF Ceramic]   ──► Signal GND (High-Frequency Decoupling)
│
▼
[Regulated VCC Bus / 3V3_EXT Rail to Pico & Sensor Interfaces]

Component Specifications & Engineering Justification

DesignatorComponentSpecification / PackageEngineering Function
GD1Gas Discharge Tube (GDT)2-Electrode Axial (Spark-over: ~90V–230V)Primary surge barrier. Shunts high-energy transient spikes (kA surge capacity) directly to earth ground without burning the PCB traces.
D1, D3Schottky Barrier DiodeSS14 (1A / 40V, SMA / DO-214AC)Blocks reverse-polarity voltage connection with ultra-low forward voltage drop ($V_F \approx 0.35\text{V}$) on input buses.
D2, D4TVS / Clamping DiodeSMAJ5.0A (SMA / DO-214AC)Suppresses residual fast transients and clamps overvoltage to safe logic thresholds within nanosecond response times.
C1, C3Electrolytic Capacitor100µF (Radial, Low ESR)Absorbs input voltage dips and supplies peak burst current during Wi-Fi / LoRa transmission cycles.
C2, C4Ceramic Capacitor100nF (Radial / Multilayer)Suppresses high-frequency switching noise adjacent to power distribution headers.
J1, J2Female Pin Headers1x20 Pin 2.54mm PitchSocket interface for Raspberry Pi Pico 2 / Pico 2W.

Power Subsystem & Battery Management

  • Supported Input Topology: 1S Li-ion / LiFePO4 battery pack (1S1P, 1S2P, 1S4P) or 5V DC step-down source.
  • Operating Input Range: 1.8V to 5.5V DC (Strictly single-cell architecture; do NOT connect 2S, 3S, or 4S packs directly without external regulation).
  • External BMS Coordination: Designed to interface with an external 1S Lithium BMS module handling cell balancing, overcharge (4.2V cut-off), and deep over-discharge protection.
  • Dedicated Sensor Power Bus (3V3_EXT): Independent power tap engineered to prevent high-draw peripheral sensors from loading or resetting the internal Pico voltage regulator.

Commissioning & Verification Guide (Smoke Test)

Step 1: Cold Test & Continuity Inspection (Unpowered)

  1. Verify silkscreen polarity symbols (+, -, and *Earth ⏚) across all terminal blocks.
  2. Check resistance with a digital multimeter between VCC and GND across all power rails.
    • Pass Criteria: High impedance / open circuit ($>1\text{ M}\Omega$).
  3. Verify that *Earth ⏚ is completely isolated from system GND on the multimeter.
  4. Test diodes D1–D4 in Diode Check mode to ensure correct cathode/anode orientation.

Step 2: First Power-Up (Current-Limited Test)

  1. Set a bench power supply to 3.8V DC with the current limit restricted to 50mA.
  2. Connect leads to the power terminal blocks (without the Raspberry Pi Pico mounted).
  3. Measure voltage rails at pin sockets: verify clean DC voltage across VCC, 3V3_EXT, and ground buses.
    • Pass Criteria: Quiescent current remains $<1\text{mA}$; no thermal dissipation across protection diodes.

Step 3: Full-Load Runtime Validation

  1. Power down and securely seat the Raspberry Pi Pico 2 / 2W into headers J1 and J2.
  2. Increase the power supply current limit to 500mA.
  3. Flash edge telemetry firmware and verify Wi-Fi/LoRa transmission stability under active load.

Render Board

Roadmap

  • Rev 1.0 (Prototype): Initial 2-layer modular layout; verified discrete protection logic and basic terminal block layout.
  • Rev 1.1 (Current Production):
    • Added dedicated Primary Surge Stage via Gas Discharge Tube (GD1) paired with isolated *Earth ⏚ terminal block.
    • Symmetrical dual-rail topology with auxiliary high-current sensor power (3V3_EXT).
    • Optimized footprint clearances (eliminated SMD diode soldering crowding from Rev 1.0).
    • Strict 45° trace angle routing across both layers to eliminate acid traps and maintain signal integrity.
  • Rev 2.0 (Planned): 4-layer impedance-controlled stackup with dedicated inner ground and power planes (L2/L3), integrated MIFA antenna, and expanded energy-harvesting interfaces.

Parts

28
QtyValueFootprintReferences
3TerminalBlock_Phoenix_MKDS-1,5-4_1x04_P5.00mm_HorizontalTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-4_1x04_P5.00mm_HorizontalH1, H2, H3
20.1uFCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mmC2, C3
2100uFCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC1, C4
2Conn_01x01Connector_Wire:SolderWire-0.25sqmm_1x01_D0.65mm_OD2mmJ6, J7
2Conn_01x20Connector_PinSocket_2.54mm:PinSocket_1x20_P2.54mm_VerticalJ1, J2
2PolyfuseFuse:Fuse_Bourns_MF-RHT050F1, F2
2SMAJ5.0ADiode_SMD:D_SMAD2, D4
2SS14Diode_SMD:D_SMAD1, D3
2Screw_Terminal_01x02TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_HorizontalJ3, J8
1Conn_01x02Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_HorizontalJ5
1Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalRESET1
1Conn_01x08Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_HorizontalJ4
1GDT_2PinResistor_THT:R_Axial_DIN0411_L9.9mm_D3.6mm_P15.24mm_HorizontalGD1
1TerminalBlock_Phoenix_MKDS-1,5-4_1x04_P5.08mm_HorizontalTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-4_1x04_P5.00mm_HorizontalH4

The 24 most common of 28 parts.

Similar boards

  • 2 layers405 × 135 mmKeyboard, the printed circuit board in 3D

    Keyboard

    jasperhax0r/CompaqPortableKeyboard

    Mechanical Keyboard for the original Compaq Portable XT-Class

    188 parts2MIT
  • 2 layers76 × 61 mmGemilaimate compact, the printed circuit board in 3D

    Gemilaimate compact

    rico-x/GemilaiMate

    Gemilai 3007Z DIY carrier and standalone firmware. Prototype: hardware not assembled or tested.

    110 parts2
  • 2 layers85 × 55 mmBreezy Redesign, the printed circuit board in 3D

    Breezy Redesign

    BackSlasher/breezy

    My AC controller

    29 partsMIT
  • 2 layers50 × 62 mmDong ho module, the printed circuit board in 3D

    Dong ho module

    Doantheodoisuckhoe/Thietbitheodoisuckhoe

    Bản 1.3 (30/10/2026). Mạch 2 lớp 50 × 62 mm ghép các module có sẵn, toàn bộ linh kiện hàn tay được (điện trở, tụ 0805; SOT-23; SOD-323; SMA; header 2,54 mm).

    36 parts
  • 4 layers49.9 × 56.4 mmDisplay pcb, the printed circuit board in 3D

    Display pcb

    Turboblider55/Project_OpenGauge

    Modular Vehicle Telemetry and Infotainment Companion via OBD-II

    50 parts
  • 4 layers120 × 79.5 mmNivara PCB, the printed circuit board in 3D

    Nivara PCB

    WenerrP/WENERR_PACHECO_ELECTIVA_2025_C2

    Wenerr Valentín Pacheco Torres.

    182 parts
  • 2 layers45.2 × 17.4 mmHall, the printed circuit board in 3D

    Hall

    eddyem/stm32samples

    Code samples and ready projects based on bare-metal STM32

    37 parts208
  • 2 layers70 × 45 mmBinary Counter 8Bit, the printed circuit board in 3D

    Binary Counter 8Bit

    himanshu40304/PCB_automation

    This repository contains the automation workflow and some projects made by using this workflow which makes pcb designs using ai assistance faster than making pcb designs manually.

    41 parts1

Questions

How big is the Project Zeta PCB?

It measures 80 × 80 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Project Zeta use?

28 parts, built around the SMAJ5.0A and SS14. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Project Zeta KiCad files?

From the OatMealXXII/Project_Zeta repository on GitHub, at the commit this page was made from: the board is Project_Zeta.kicad_pcb and its schematic Project_Zeta.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Project Zeta design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).