

SEVILLA ME
- Size
- 120 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 28
- Nets
- 62
- Pads
- 140
- Tracks, vias
- 177, 12
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 23 Jun 2025
- Updated
- 26 Jul 2025
Overview
SEVILLA ME is an open-source printed circuit board by Noxctis, from the Noxctis/CpE2303L repository on GitHub. It is a 2-layer board of 120 × 100 mm with 28 parts on 62 nets, routed with 177 tracks and 12 vias.
It is built around the PIC16F887-I/PT, LM1117DT-3.3 and TCA9517D. Its parts include 7 ICs, 6 capacitors, 5 resistors, 2 diodes and 2 switches. It belongs with the ESP8266 and PIC boards of this library.
Main components
3PIC16F887-I/PT
TQFP-44(10x10)-40℃~+85℃ 10bit 14KB 20MHz 256Byte 2V~5.5V 35 368Byte 8 Bit Built-in FLASH PIC TQFP-44(10x10) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)LM1117DT-3.3
TO-2520℃~+125℃@(Tj) 1 1.2V@(800mA) 15V 3.3V 5mA 75dB@(120Hz) 800mA Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive TO-252 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTCA9517D
SOIC-8-40℃~+85℃ 1 2 2.7V~5.5V 6mA 900mV~5.5V Bidirectional Buffers Open-drain Output enable high-impedance SMBus、I2C SOIC-8 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level Shifters
Parts
28| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_DIN965_Pad | H1, H2, H3, H4 |
| 3 | 10k | Resistor_SMD:R_4020_10251Metric_Pad1.65x5.30mm_HandSolder | R2, R4, R5 |
| 2 | 0.1uF | Capacitor_THT:C_Disc_D3.0mm_W2.0mm_P2.50mm | C2, C3 |
| 2 | 100uF | Capacitor_THT:CP_Axial_L10.0mm_D4.5mm_P15.00mm_Horizontal | C4, C5 |
| 2 | LED | LED_SMD:LED_2010_5025Metric_Pad1.52x2.65mm_HandSolder | D1, D2 |
| 2 | SW_Push | Button_Switch_THT:SW_PUSH_6mm_H4.3mm | SW1, SW2 |
| 1 | 1000uF | Capacitor_THT:CP_Axial_L10.0mm_D6.0mm_P15.00mm_Horizontal | C1 |
| 1 | 10uF | Capacitor_THT:CP_Axial_L10.0mm_D6.0mm_P15.00mm_Horizontal | C6 |
| 1 | 1k | Resistor_SMD:R_4020_10251Metric_Pad1.65x5.30mm_HandSolder | R1 |
| 1 | 470 | Resistor_SMD:R_4020_10251Metric_Pad1.65x5.30mm_HandSolder | R3 |
| 1 | Barrel_Jack_Switch | Connector_BarrelJack:BarrelJack_Horizontal | J2 |
| 1 | ESP-01v090 | ESP8266:ESP-01 | U7 |
| 1 | LM1117DT-3.3 | Package_TO_SOT_SMD:TO-252-3_TabPin2 | U2 |
| 1 | LM35-NEB | Package_TO_SOT_THT:TO-220-3_Vertical | U3 |
| 1 | LM7805_TO220 | Package_TO_SOT_THT:TO-220-3_Vertical | U1 |
| 1 | PIC16F887-IP | Package_DIP:DIP-40_W15.24mm | U4 |
| 1 | RC1602A-GHW-ESX | Display:RC1602A | U5 |
| 1 | R_Potentiometer | Potentiometer_THT:Potentiometer_ACP_CA6-H2,5_Horizontal | RV1 |
| 1 | TCA9517D | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U6 |
More from Noxctis/CpE2303L
8- 2 layers120 × 100 mm

- 2 layers66.8 × 60 mm

- 2 layers77 × 36 mm

- 2 layers100 × 50 mm

- 2 layers81.8 × 77.5 mm

- 2 layers36.5 × 45.5 mm

- 2 layers70 × 40 mm

- 2 layers27.5 × 26.5 mm

Similar boards
- 2 layers112 × 98 mm

Sourccey pcb
vulcan-forge/sourccey-electrical
Open Source Electrical Repository for Sourccey
163 parts2CERN-OHL-S-2.0 - 2 layers65 × 56 mm

PiADC2
capconix/PiADC2
PiADC open source project successor, the PiADC2 - A simple data acquisition board for use with the model B Raspberry Pis
72 parts1 - 4 layers65 × 26 mm

- 2 layers110 × 110 mm

- 2 layers71.5 × 36 mm

- 2 layers95 × 78 mm

- 2 layers45 × 95 mm

Sub uproc
duanestorey/hifi-amp
A high-fidelity four-channel amplifier with active-crossovers and room correction
59 parts1 - 4 layers80 × 49 mm

Questions
How big is the SEVILLA ME PCB?
It measures 120 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the SEVILLA ME use?
28 parts, built around the PIC16F887-I/PT, LM1117DT-3.3 and TCA9517D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the SEVILLA ME KiCad files?
From the Noxctis/CpE2303L repository on GitHub, at the commit this page was made from: the board is SEVILLA_ME/SEVILLA_ME.kicad_pcb and its schematic SEVILLA_AS2/SEVILLA_AS2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the SEVILLA ME design in my own project?
Its repository states no licence, so its author keeps all rights: ask Noxctis before reusing the design.