2 layers15 × 31 mm
2 layers75 × 70 mm
IPicoV5 Panelized
MiniProjectDIY/iPico5RP2350 based UF2 hardware security key
- Size
- 75 × 70 mm
- Copper layers
- 2
- Thickness
- 1.2 mm
- Parts
- 228
- Nets
- 63
- Pads
- 923
- Tracks, vias
- 1,430, 225
- Pours
- 305
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 19 Apr 2025
- Updated
- 19 Apr 2025
Overview
IPicoV5 Panelized is an open-source printed circuit board by MiniProjectDIY, from the MiniProjectDIY/iPico repository on GitHub, published under the CC0-1.0 licence. It is a 2-layer board of 75 × 70 mm with 228 parts on 63 nets, routed with 1,430 tracks and 225 vias.
It is built around the ZD25WQ32CEIGR, TPESD0402G05V and ABM8-272-T3, with the AOTA-B201610S3R3-101-T, BSMD0402L-020 and GT-USB-8016A among its other parts. Its parts include 95 capacitors, 40 resistors, 20 ICs, 15 diodes and 5 connectors. It belongs with the RP2350 boards of this library.
Main components
7
ZD25WQ32CEIGR
USON-8(2x3)-40℃~+85℃ 1.65V~3.6V 100,000 cycles 104MHz 10ms 20 Years 2ms 32Mbit 7uA Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI USON-8(2x3) NOR FLASH ROHSZettaNOR FLASH
TPESD0402G05V
0402-55℃~+125℃ 0.05pF 1 10nA 40V 5V Bidirectional IEC 61000-4-2 0402 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)
ABM8-272-T3
SMD3225-4P-40℃~+85℃ 10pF 12MHz 50Ω SMD crystal oscillator ±30ppm ±30ppm SMD3225-4P Crystals ROHSAbraconCrystals
AOTA-B201610S3R3-101-T
0806115mΩ 2.1A 2.4A 3.3uH Molded inductor 0806 Molding Power Inductors ROHSAbraconPower InductorsBSMD0402L-020
0402-40℃~+85℃ 0.65mm 0.6mm 1.15mm 1.25Ω 100mΩ 1s 200mA 40A 500mA 500mW 6V 0402 Resettable Fuses ROHSBHFUSEResettable FusesGT-USB-8016A
SMD-40℃~+85℃ 0.15mm 1 12mm 9P Black Laminated board Male Type-C USB 2.0 SMD USB Connectors ROHSG-SwitchUSB Connectors
NCD0603B1
0603-30℃~+85℃ 10mA 130° 2.6V~3.6V 220mcd 463nm~475nm 465nm 72mW Blue Discrete Diode 0603 LED Indication - Discrete ROHSFoshan NationStar OptoelectronicsLED Indication - Discrete
README
README.mdiPico
RP2350 based UF2 hardware security key
Hardware
iPico use the same IO as official raspberry pi Pico2 board, just replaced physical push button with capacitive touch button on pcb and change usb connector from female to male.
Firmware
Use pico-fido firmware for pico 2 board will do.
Enclosure
3d printed case using file from 3D folder,using M1.4* 2 heat inserts and M1.4*5 counter sink screws.
Parts
228| Qty | Value | Footprint | References |
|---|---|---|---|
| 40 | C_0402_100nF_10V_X7R | Capacitor_SMD:C_0402_1005Metric | C11, C11, C11, C11, C11, C12, C12, C12, C12, C12, C14, C14, C14, C14, C14, C15 +24 |
| 35 | C_0402_4.7uF_10V_X5R | Capacitor_SMD:C_0402_1005Metric | C1, C1, C1, C1, C1, C2, C2, C2, C2, C2, C20, C20, C20, C20, C20, C21 +19 |
| 20 | M1.4 Hole | LT_TinyMountingHole:MountingHole-M1.4 | H1, H1, H1, H1, H1, H2, H2, H2, H2, H2, H3, H3, H3, H3, H3, H4 +4 |
| 15 | R_0402_27_5% | Resistor_SMD:R_0402_1005Metric | R2, R2, R2, R2, R2, R3, R3, R3, R3, R3, R4, R4, R4, R4, R4 |
| 10 | C_0402_15pF_50V_C0G | Capacitor_SMD:C_0402_1005Metric | C13, C13, C13, C13, C13, C16, C16, C16, C16, C16 |
| 10 | R_0402_1K_5% | Resistor_SMD:R_0402_1005Metric | R5, R5, R5, R5, R5, R6, R6, R6, R6, R6 |
| 10 | TPESD0402G05V | Resistor_SMD:R_0402_1005Metric | D1, D1, D1, D1, D1, D2, D2, D2, D2, D2 |
| 5 | 662K | Package_TO_SOT_SMD:SOT-23 | U5, U5, U5, U5, U5 |
| 5 | ABM8-272-T3 | Crystal:Crystal_SMD_2520-4Pin_2.5x2.0mm | Y1, Y1, Y1, Y1, Y1 |
| 5 | AOTA-B201610S3R3-101-T | LT_Inductor:LT_L0806 | L1, L1, L1, L1, L1 |
| 5 | BSMD0402L-020 | Fuse:Fuse_0402_1005Metric | F1, F1, F1, F1, F1 |
| 5 | C_0402_1pF_50V_C0G | Capacitor_SMD:C_0402_1005Metric | C4, C4, C4, C4, C4 |
| 5 | C_0402_1uF_10V_X5R | Capacitor_SMD:C_0402_1005Metric | C3, C3, C3, C3, C3 |
| 5 | GT-USB-8016A | LT_GT-USB-8016A:GT-USB-8016A | J1, J1, J1, J1, J1 |
| 5 | Jumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP1, JP1, JP1, JP1, JP1 |
| 5 | NCD0603B1 | LED_SMD:LED_0603_1608Metric | D3, D3, D3, D3, D3 |
| 5 | RP2350A-QFN60 | LT_QFN60:RP2350A_QFN-60_EP_7.75x7.75_Pitch0.4mm | U2, U2, U2, U2, U2 |
| 5 | R_0402_33_5% | Resistor_SMD:R_0402_1005Metric | R10, R10, R10, R10, R10 |
| 5 | R_0402_470_5% | Resistor_SMD:R_0402_1005Metric | R7, R7, R7, R7, R7 |
| 5 | R_0402_5.1K_5% | Resistor_SMD:R_0402_1005Metric | R1, R1, R1, R1, R1 |
| 5 | TTP223_SOT23-6 | Package_TO_SOT_SMD:SOT-23-6 | U4, U4, U4, U4, U4 |
| 5 | TestPoint | LT_TestPoint:TP_8MM | TP1, TP1, TP1, TP1, TP1 |
| 5 | ZD25WQ32CEIGR | LT_USON8:USON8-2x3mm-EP0.2x1.6mm | U1, U1, U1, U1, U1 |
| 2 | , |
The 222 most common of 228 parts.
More from MiniProjectDIY/iPico
1Similar boards
- 2 layers73.5 × 47.5 mm
- 2 layers93 × 52 mm
- 4 layers140 × 100 mm
Rcm dish controller
jrseti/Dish
Simple controller with toggle switches to move the dish motors
314 partsCC0-1.0 - 4 layers100 × 100 mm
- 4 layers150 × 100 mm
Cm4-robo controller
jrseti/roboclaw-cm4-dc-dish-controller
Satellite dish controller using a ROBOCLAW-2X15A-OEM controlled by a Raspberry Pi CM4 module. Powered by DC battery.
292 partsMIT - 2 layers37.3 × 31.8 mm
- 6 layers29 × 33 mm
MINIREX G4
mathieupommery/MINIREX_G473
The following table demonstrates the estimated component costs based on Mouser volume pricing. The unit price of each component dynamically adapts to the total quantity required for the entire production batch (1, 100…
109 parts10 - 4 layers74 × 48 mm
CastleBox NeoPro
zeankundev/boards
A collection and an archive of KiCad projects I made. Contains projects from 2023 - 2024.
107 parts1
Questions
How big is the IPicoV5 Panelized PCB?
It measures 75 × 70 mm and has 2 copper layers, 1.2 mm thick.
What parts does the IPicoV5 Panelized use?
228 parts, built around the ZD25WQ32CEIGR, TPESD0402G05V, ABM8-272-T3 and AOTA-B201610S3R3-101-T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the IPicoV5 Panelized KiCad files?
From the MiniProjectDIY/iPico repository on GitHub, at the commit this page was made from: the board is iPicoV5_Panelized/iPicoV5_Panelized.kicad_pcb and its schematic iPicoV5_Panelized/iPicoV5_Panelized.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the IPicoV5 Panelized design in my own project?
Its repository publishes it under the CC0-1.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).