
Module-4ch dimmer
MikkoTervala/modular-esp32-dimmer
ESP32 based led dimmer with modular components

ESP32 based led dimmer with modular components
Module esp32 is an open-source printed circuit board by MikkoTervala, from the MikkoTervala/modular-esp32-dimmer repository on GitHub. It is a 2-layer board of 50 × 25 mm with 26 parts on 30 nets, routed with 159 tracks and 22 vias.
It is built around the ESP32-C3-WROOM-02-H4. Its parts include 6 resistors, 3 capacitors, 3 connectors, 2 diodes and 2 switches. It belongs with the ESP32 and RISC-V boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 10k | Resistor_SMD:R_0603_1608Metric | R1, R2, R5 |
| 3 | JLCPCB tooling hole | ESP32_dimmer_footprints:JLCPCB tooling hole | H3, H4, H5 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R3, R4 |
| 2 | Conn_01x08_Pin | Connector_PinHeader_1.27mm:PinHeader_1x08_P1.27mm_Vertical_SMD_Pin1Right | J2, J3 |
| 2 | MountingHole-Spacer | MountingHole:MountingHole_2.5mm | H1, H2 |
| 1 | 1N5819WS 1A 40V | Diode_SMD:D_SOD-323 | D1 |
| 1 | 1µF | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 2.7k | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 3V3 | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | BOOT | ESP32_dimmer_footprints:SW_SPST_PTS810 | SW2 |
| 1 | C3 220nf | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | C4 10µf | Capacitor_SMD:C_1206_3216Metric | C3 |
| 1 | ESP32-C3-WROOM-02-H4 | ESP32_dimmer_footprints:MODULE_ESP32-C3-WROOM-02-H4 | U1 |
| 1 | GND | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | LED White KT-0603W | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | RESET | ESP32_dimmer_footprints:SW_SPST_PTS810 | SW1 |
| 1 | RX | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | TX | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | USB_C_Receptacle_USB2.0 | ESP32_dimmer_footprints:CONN_TYPE-C-31-M-12 | J1 |

MikkoTervala/modular-esp32-dimmer
ESP32 based led dimmer with modular components
Spritetm/picframe_colepd
A WiFi picture frame allowing for remote photo uploads, using an ESP32-C3 and a 5.6" color E-ink display



nepyope/Project-Homunculus
Project Homunculus is open-source, low-cost hardware for capturing human hand and arm motions. It has two parts.

exico91/SommerESP
A plug and play ESP32-C3 board to control Sommer garage doors


emertcakir/OpenAirScope
Open-source air quality and environmental monitoring node with STM32H743 + ESP32-C3, LoRaWAN, RS485, USB-C, Li-ion charging, and multi-sensor support.
It measures 50 × 25 mm and has 2 copper layers, 1.6 mm thick.
26 parts, built around the ESP32-C3-WROOM-02-H4. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the MikkoTervala/modular-esp32-dimmer repository on GitHub, at the commit this page was made from: the board is module-esp32/module-esp32.kicad_pcb and its schematic module-4ch-dimmer/module-4ch-dimmer.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask MikkoTervala before reusing the design.