Skip to the content
4 layers140 × 136 mmVinyl adc rev d, the printed circuit board in 3D

Vinyl adc rev d

MadsRudolph/vinyl-adc1

Discrete 3rd-order delta-sigma stereo audio ADC, built from op-amps and logic gates: a four-layer Raspberry Pi HAT made by PCBWay, with KiCad files, SPICE simulations and measurements

Size
140 × 136 mm
Copper layers
4
Thickness
1.6 mm
Parts
184
Nets
104
Pads
643
Tracks, vias
1,020, 13
Pours
3
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
3 Sep 2026
Updated
4 Nov 2026

Overview

Vinyl adc rev d is an open-source printed circuit board by MadsRudolph, from the MadsRudolph/vinyl-adc repository on GitHub. It is a 4-layer board of 140 × 136 mm with 184 parts on 104 nets, routed with 1,020 tracks and 13 vias.

It is built around the 74HC244D, TL072 and LM358, with the 74HC04D, 74HC74D and LM311 among its other parts. Its parts include 69 resistors, 52 capacitors, 20 ICs, 16 diodes and 10 connectors. It belongs with the audio and music boards of this library.

Main components

12

README

hardware/kicad/osc_module/README.md

6.144 MHz oscillator module

A coaster-sized single-sided board that fills the X1 DIP-8 socket on the already-built digital board, standing in for the unobtainable oscillator can. Electrically it is the can: a Pierce oscillator (74HCU04 + the found 2-pin 6.144 MHz crystal) whose buffered output leaves on the socket's OUT pin. The same blk_pierce block draws this module, the rev B digital board and the sim_i_pierce testbench, so the three cannot drift apart. Design rationale, and the two values that are load-bearing (R_s = 2k2, and unbuffered 74HCU04): docs/design-notes.md §5.

Parts

RefValuePackageShop?
U974HCU04 (unbuffered!)DIP-14 + socketorder (pin-identical to 74HC04)
Y16.144 MHz crystalHC-49in hand
R101Maxialshop
R112k2axialshop (2k21 E96 fine)
C16, C1727pceramic discshop (22p/33p also fine)
C9100nceramic discshop
J14 machined pinsat DIP-8 positions 1/4/5/8shop pin strip

A buffered 74HC04 in U9's socket is an emergency substitute only — verify with a scope that the output is 6.144 MHz and not ~30 MHz before trusting it (the buffered gate can oscillate through the crystal's holder capacitance).

Build order

  1. Solder the four J1 pins first, from the component side, pointing down: machined round pins (cut from a strip) at pad positions 1, 4, 5 and 8 — the corners of the pad field. Pads 2/3/6/7 stay empty. Seat them in a spare DIP-8 socket while soldering so they cure straight.
  2. Low parts next (R10, R11, C16, C17, C9), then the DIP-14 socket, then Y1.
  3. Plug in the 74HCU04 last.

Fitting it to the digital board

  • Pad 1 of the module goes over pin 1 of the X1 socket (the socket's notch end). Both are marked; a 180° misfit puts +5 V on the clock output.
  • The module body extends east and south from the socket, over the board's emptiest quarter. Its north edge sits just clear of the CLK-SEL jumper — J1 on the digital board must be jumpered 1-2 (crystal) with the module in place, so fit that jumper first.
  • Height: the module rides ~8 mm above the digital board on the socket + pin stack. Its far east edge passes close over U3's socket; if it touches, stack a second machined-pin socket under the module as a spacer.
  • The enclosure lid was drawn for a bare digital board — check the module clears the acrylic before closing it, and bench-test with the lid off until then.

Bench check

Power the digital board, jumper J1 1-2, and scope the socket's pin 5 (or U3 pin 1): a 5 V square wave at 6.144 MHz ±0.01 %. The 74HC4040 then gives BCLK 3.072 MHz on Q0 and LRCLK 48 kHz on Q6 as in the testing guide.

Files

  • vinyl_adc_osc.kicad_sch — drawn by hardware/kicad/tools/osc_module_layout.py
  • vinyl_adc_osc.kicad_pcb — placed by vinyl_adc_osc.place.py, routed single-sided: 19/19 connections, zero wire bridges, zero vias, DRC clean
  • production/vinyl_adc_osc/ — mill Gerbers + Excellon drill, laser silk DXF

Parts

184
QtyValueFootprintReferences
31100nC_Disc_D5.0mm_W2.5mm_P5.00mmC2, C3, C10, C11, C13, C15, C19, C25, C26, C27, C28, C29, C30, C31, C44, C45 +15
1310k0R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR2, R3, R4, R5, R31, R32, R43, R48, R50, R51, R53, R71, R72
91k00R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR16, R20, R40, R41, R42, R52, R57, R58, R60
822k1R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR33, R35, R36, R44, R46, R73, R75, R76
6220pC_Disc_D5.0mm_W2.5mm_P5.00mmC22, C23, C24, C62, C63, C64
4100kR_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR45, R47, R49, R59
410uCP_Radial_D5.0mm_P2.50mmC4, C41, C42, C43
413k0R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR25, R26, R65, R66
414k7R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR22, R23, R62, R63
41N4148D_DO-35_SOD27_P7.62mm_HorizontalD11, D12, D13, D14
48k25R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR29, R30, R69, R70
4MountingHole_2.7mm_M2.5MountingHole_2.7mm_M2.5H4, H5, H6, H7
4TL072DIP-8_W7.62mm_LongPadsU20, U22, U60, U62
31n5C_Disc_D5.0mm_W2.5mm_P5.00mmC21, C40, C61
3330RR_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR54, R55, R56
3GREENLED_D5.0mmD3, D5, D10
3MountingHole_3.2mm_M3MountingHole_3.2mm_M3H1, H2, H3
3REDLED_D5.0mmD6, D7, D8
210k5R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR24, R64
210uL_Axial_L12.0mm_D5.0mm_P15.24mm_Horizontal_Fastron_MISCL1, L2
2165kR_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR34, R74
21N4003D_DO-41_SOD81_P10.16mm_HorizontalD15, D16
21N5817D_DO-41_SOD81_P10.16mm_HorizontalD1, D2
220k5R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR21, R61
2220uCP_Radial_D8.0mm_P3.50mmC5, C6
2255kR_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR27, R67
227pC_Disc_D5.0mm_W2.5mm_P5.00mmC16, C17
22k21R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR37, R77
22u2C_Rect_L11.0mm_W6.3mm_P10.00mm_MKTC20, C60
2470uCP_Radial_D10.0mm_P5.00mmC1, C18
2475RR_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR12, R13
247kPinHeader_1x03_P2.54mm_HorizontalRV20, RV60
25k90R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR28, R68
274HC04DIP-14_W7.62mm_LongPadsU24, U64
274HC244DIP-20_W7.62mm_LongPadsU1, U10
274HC74DIP-14_W7.62mm_LongPadsU23, U63
2BC557TO-92_InlineQ2, Q3
2LM311DIP-8_W7.62mm_LongPadsU21, U61
2YELLOWLED_D5.0mmD4, D9
110R0R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR17
11MR_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR10
124LC32DIP-8_W7.62mm_LongPadsU11
12k2R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR11
133R2R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR14
13k92R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR15
14R75R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1
16.144MHzCrystal_HC49-U_VerticalY1
174HC157DIP-16_W7.62mm_LongPadsU6
174HC4040DIP-16_W7.62mm_LongPadsU4
174HC4049DIP-16_W7.62mm_LongPadsU8
174HCT132DIP-14_W7.62mm_LongPadsU3
174HCU04DIP-14_W7.62mm_LongPadsU9
1BC547TO-92_InlineQ1
1CLK SELPinHeader_1x03_P2.54mm_VerticalJ1
1GND LIFTPinHeader_1x02_P2.54mm_VerticalJ4
1LINE IN LTerminalBlock_bornier-2_P5.08mmJ20
1LINE IN RTerminalBlock_bornier-2_P5.08mmJ60
1LM339DIP-14_W7.62mm_LongPadsU12
1LM358DIP-8_W7.62mm_LongPadsU2
1RASPBERRY PI 4PinSocket_2x20_P2.54mm_VerticalJ2
1SHUTDOWN / WAKE GPIO3SW_PUSH_6mmSW1
1TONEARM GNDTerminalBlock_bornier-2_P5.08mmJ3
1TP DIGPinHeader_2x05_P2.54mm_VerticalJ5
1TP LPinHeader_2x05_P2.54mm_VerticalJ22
1TP RPinHeader_2x05_P2.54mm_VerticalJ62
1USER GPIO23SW_PUSH_6mmSW2
1WPPinHeader_1x02_P2.54mm_VerticalJ6

More from MadsRudolph/vinyl-adc

6
  • 4 layers118 × 88 mmVinyl adc rev e, the printed circuit board in 3D

    Vinyl adc rev e

    MadsRudolph/vinyl-adc

    Discrete 3rd-order delta-sigma stereo audio ADC, built from op-amps and logic gates: a four-layer Raspberry Pi HAT made by PCBWay, with KiCad files, SPICE simulations and measurements

    184 parts1
  • 4 layers170 × 120 mmVinyl adc rev c, the printed circuit board in 3D

    Vinyl adc rev c

    MadsRudolph/vinyl-adc

    Discrete 3rd-order delta-sigma stereo audio ADC, built from op-amps and logic gates: a four-layer Raspberry Pi HAT made by PCBWay, with KiCad files, SPICE simulations and measurements

    119 parts1
  • 2 layers100 × 100 mmVinyl adc channel l, the printed circuit board in 3D

    Vinyl adc channel l

    MadsRudolph/vinyl-adc

    Discrete 3rd-order delta-sigma stereo audio ADC, built from op-amps and logic gates: a four-layer Raspberry Pi HAT made by PCBWay, with KiCad files, SPICE simulations and measurements

    43 parts1
  • 2 layers100 × 100 mmVinyl adc digital, the printed circuit board in 3D

    Vinyl adc digital

    MadsRudolph/vinyl-adc

    Discrete 3rd-order delta-sigma stereo audio ADC, built from op-amps and logic gates: a four-layer Raspberry Pi HAT made by PCBWay, with KiCad files, SPICE simulations and measurements

    38 parts1
  • 2 layers100 × 100 mmVinyl adc power, the printed circuit board in 3D

    Vinyl adc power

    MadsRudolph/vinyl-adc

    Discrete 3rd-order delta-sigma stereo audio ADC, built from op-amps and logic gates: a four-layer Raspberry Pi HAT made by PCBWay, with KiCad files, SPICE simulations and measurements

    24 parts1
  • 2 layers41.9 × 44 mmVinyl adc osc, the printed circuit board in 3D

    Vinyl adc osc

    MadsRudolph/vinyl-adc

    Discrete 3rd-order delta-sigma stereo audio ADC, built from op-amps and logic gates: a four-layer Raspberry Pi HAT made by PCBWay, with KiCad files, SPICE simulations and measurements

    8 parts1

Similar boards

  • 4 layers100 × 100 mmEth, the printed circuit board in 3D

    Eth

    imihajlow/ccpu

    A 8-bit computer made of 74xx series logic gates and memory ICs.

    101 parts145
  • 2 layers216 × 150 mmMotherboard-101, the printed circuit board in 3D

    Motherboard-101

    artemisamsx/artemisa

    Schematics, PCB designs and HDL simulations to build a 8-bits MSX computer

    124 parts67
  • 2 layers245.1 × 160 mm8-Bit CPU 32k, the printed circuit board in 3D

    8-Bit CPU 32k

    slu4coder/Minimal-64x4-Home-Computer

    My DIY TTL home computer with VGA and PS/2 and 4x the processing power of a Commodore C64 or Apple II.

    139 parts326
  • 2 layers177.8 × 130.8 mmDurango, the printed circuit board in 3D

    Durango

    zuiko21/minimOS

    Scalable OS for 6502/65816

    159 parts23MIT
  • 2 layers208 × 110 mm8 16 computer 2, the printed circuit board in 3D

    8 16 computer 2

    halfburnttoast/TCPU816-v1

    Version 1.1 of my 8-bit, TTL computer.

    120 parts21
  • 2 layers234 × 100 mmV2b, the printed circuit board in 3D

    V2b

    KITTY-6502/hardware

    the KITTY is a 65c02 homebrew kit microcomputer designed around text mode graphics and cartridge media. It is fully open source, and uses exclusively in-production parts.

    147 parts
  • 2 layers99.6 × 99.7 mmRp2c02-isa, the printed circuit board in 3D

    Rp2c02-isa

    taka-tuos/rp2c02-isa

    RP2C02 ISA Card

    49 parts1MIT
  • 2 layersCES, the printed circuit board in 3D

    CES

    erickpires/CES-PCB

    170 partsMIT

Questions

How big is the Vinyl adc rev d PCB?

It measures 140 × 136 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Vinyl adc rev d use?

184 parts, built around the 74HC244D, TL072, LM358 and 74HC04D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Vinyl adc rev d KiCad files?

From the MadsRudolph/vinyl-adc repository on GitHub, at the commit this page was made from: the board is hardware/kicad/rev_d/vinyl_adc_rev_d.kicad_pcb and its schematic hardware/kicad/channel_l/vinyl_adc_channel_l.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Vinyl adc rev d design in my own project?

Its repository states no licence, so its author keeps all rights: ask MadsRudolph before reusing the design.