Skip to the content
4 layers72 × 72 mmMARV V2-panel, the printed circuit board in 3D

MARV V2-panel

Lmx154/MARV-V2-PCB

A small RP2354B flight controller for rockets and drones: a 6-axis IMU, a high-g accelerometer and a barometer on their own buses, native four-bit microSD logging, USB-C, and an IO block for GPS, ELRS, a magnetometer…

Size
72 × 72 mm
Copper layers
4
Thickness
1.6 mm
Parts
110
Nets
97
Pads
450
Tracks, vias
867, 200
Pours
535
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
17 Sep 2026
Updated
27 Oct 2026

Overview

MARV V2-panel is an open-source printed circuit board by Lmx154, from the Lmx154/MARV-V2-PCB repository on GitHub. It is a 4-layer board of 72 × 72 mm with 110 parts on 97 nets, routed with 867 tracks and 200 vias.

It is built around the 1N5819WS and AO3401A. Its parts include 41 capacitors, 31 resistors, 2 ICs, 2 inductors and 2 crystals. It belongs with the robots and motor control boards and the RP2350 boards of this library.

Main components

2

README

README.md

MARV V2 flight controller

A small RP2354B flight controller for rockets and drones: a 6-axis IMU, a high-g accelerometer and a barometer on their own buses, native four-bit microSD logging, USB-C, and an IO block for GPS, ELRS, a magnetometer and servos. Power conversion uses a purchased module that plugs onto the board at J17, so the converter and FC mount as one unit; the FC takes its regulated 5 V (or USB) and makes its own 3.3 V rails.

License: hardware/docs CC0, code 0BSD, no attribution required. Provided as-is; see LICENSE.md.

Open MARV-V2.kicad_pro in KiCad 10. The repository holds the schematic and routed board, local footprints and 3D models, a datasheet source index, the design checks, and the input-power simulation. There is no firmware here.

Status, Rev 1 (2026-10-27): routed; manufacturing frame and production/ package regenerated from this revision. Source DRC: 206 violations (22 accepted errors, 184 warnings), 0 unconnected, 0 schematic-parity issues. The accepted errors are 18 GND-via hole clearances in the RP2350 (U20) exposed pad (JLC hole-in-pad rule), 3 USB pair clearances at the connector and MCU pins, and 1 SW1/J10 courtyard overlap. ERC: 0 violations. The 72 × 72 mm manufacturing frame supplies rails/fiducials for Standard assembly. Review JLCPCB previews before ordering. Before ordering, also confirm with HCI that the X1 1521H-32K000J18DTSL "J18" build is rated for 3.3 V (see datasheets/README.md).

Converter and ESC pads: J17 is a 1x03, 2.54 mm converter interface (1 OUT+, 2 GND, 3 IN+) with no EN contact. J3 is an eight-pad ESC pad row; pad 7 is raw battery VIN. See converter review.

Design specification · GPIO pinout · Libraries · Datasheets · JLCPCB DFM and routing · Working rules

See the results without running anything: the results website shows the ngspice power-input waveforms, the netlist and footprint checks, and the DRC/ERC summary for the current revision. Refresh it with python3 tools/build_site.py (writes site/; pushing site/ to master republishes it via GitHub Pages).

Repository map

text
MARV-V2.kicad_pro / _pcb / _sch    project, routed board, root schematic
*.kicad_sch                        11 sub-sheets: power OR / 3V3 / VBAT, MCU, IMU, high-g, baro, SD, USB & debug, IO block, QSPI expansion
MARV-V2.kicad_dru, MARV_Sensors.kicad_sym, *-lib-table    custom rules, project symbols, library tables
MARV-V2-panel.kicad_*              one-board manufacturing frame for Standard assembly with customer-supplied rails
fabrication-toolkit-options.json   native Fabrication Toolkit settings for JLCPCB order exports
DESIGN_SPEC.md, PINOUT.md          intended circuit, boundaries and design decisions; every GPIO with its alternates
LIBRARIES.md, AGENTS.md            footprint/model provenance; working rules
MARV_Packages.pretty/, .3dshapes/  local footprints and STEP models
datasheets/                        datasheet source index (PDFs are downloaded locally, not distributed)
tools/                             netlist checker, footprint audit, input-power simulation, PCB renderer, 3d/ (STEP inspection)
tools/panel/                       manufacturing-frame sync and checks; README has the refresh sequence
simulations/                       input-power SPICE deck, README and generated results
reports/                           decision and review records (table below)
orders/rev1/                       Rev 1 JLCPCB order record: exact upload files, all order options, BOM as ordered
images/                            PCB renders used in this README
site/                              results website (simulation, checks), built by tools/build_site.py
.github/workflows/pages.yml        publishes site/ with GitHub Pages
LICENSE.md, LICENSES/              project licence and upstream library notices
production/, build/                generated output; untracked

The board

FrontBack
MARV V2 PCB front viewMARV V2 PCB back view

3D renders of the saved PCB (regenerated 2026-10-27 with the project's own CC0 models for J4, J11, C19, X1, D20, U20 and the three sensors). J17 is the three-pin header on the front's left edge. Click either image for the full-resolution view.

To refresh both images after saving PCB changes, run:

sh
python3 tools/render_pcb.py

Requires Python 3 and KiCad 10 with its 3D model libraries. The script renders high-resolution PNGs into images/pcb/ without modifying the design. Update the images after PCB changes to keep this gallery current.

MCURP2354B (QFN-80, 2 MB in-package flash), 12 MHz crystal, USB-C device port, WS2812C status LED, RESET and BOOTSEL buttons, SWD header
Size / stack50.7 × 45.5 mm finished outline (72 × 72 mm manufacturing frame), four layers: F.Cu signals · In1 solid GND · In2 V3V3_SYS plane · B.Cu signals. 1.6 mm FR-4, 1 oz outer / 0.5 oz inner, green mask, ENIG
Rules0.15 mm minimum track and clearance (Signal netclass 0.10 / 0.10 mm), through vias only (0.60 / 0.30 mm; Signal class 0.45 / 0.30 mm), no blind/buried/micro vias — JLCPCB's standard four-layer tier with no paid options
AssemblyFront side SMT at JLCPCB (90 placements, 34 unique LCSC parts). Hand-fitted / unpopulated: ESC pad row J3 (back), SWD header J10 (front), DNP QSPI expansion U24 (front). J17 converter header is hand-fitted and excluded from the position file
MountingFour M3 grommet holes (4.0 mm) with GND rings, on a 30.5 × 30.5 mm square pattern. The 5 V converter module mounts on the FC itself at J17
ConnectorsJ3 ESC pads (current, telemetry, PWM1–4, raw battery VIN, GND), J4 USB-C, J6/J7/J8 IO block (14 rows × signal / power / GND), J10 SWD, J11 locking microSD; J17 1x03 2.54 mm converter mount (1 OUT+ / 5V_IN, 2 GND, 3 IN+ / VBAT)

Sensor suite

Every sensor has its own bus; no clock or data net is shared between devices, so each can be driven at its own rate and no transaction blocks another.

RefPartWhat it measuresBusInterrupts
U21InvenSense ICM-456866-axis IMU (gyro + accel), primary attitude sourcehardware SPI0, exclusive; 32.000 kHz HCI 1521H oscillator X1 on CLKIN (pin 9)INT1 only
U23ST LSM6DSK320Xsecondary 6-axis IMU with a ±320 g high-g channel for launch / impact / hard landingshardware SPI1, exclusiveINT1, INT2
U22Bosch BMP581barometric altitude and temperaturehardware I2C1, address 0x46INT
J11Molex 47219-2001 microSDflight logPIO + DMA, native four-bit SD—

The three sensors run from the dedicated V3V3_ANA rail with their chip-select and I²C pull-ups referenced to it, and all four interrupt lines land on independent GPIOs. Layout follows the makers' notes: the BMP581 has no copper or solder mask under its body (Bosch §8.2), and the inertial sensors sit close to the MCU with short SPI runs. Exact GPIO numbers are in PINOUT.md.

Power architecture

text
ESC V (raw battery) → J3.7 / VBAT → J17.3 VIN → converter → J17.1 VOUT
                                      ↓ 5V_IN               USB-C VBUS
                                      Q1 (AO3401A)           D1 (1N5819WS)
                                      └────────── V5_SYS ────┘
                                                    ├─ AP63203 buck → V3V3_SYS  (MCU, microSD, IO block, LDO enable)
                                                    ├─ TPS7A2033 LDO → V3V3_ANA (ICM-45686, LSM6DSK320X, BMP581, ADC_AVDD)
                                                    └─ status LED
RP2354B on-chip switcher: V3V3_SYS → 1.1 V core (laid out per RP2350 datasheet §6.3.8)
Converter VIN / J17.3 (VBAT) → 100k / 10k divider → ADC (parallel sensing branch)

Nothing that moves is powered through the FC. Motors, servos and ESCs get only their signal pins. Raw pack voltage supplies the J17 converter and voltage divider. The full boundary table is in DESIGN_SPEC.md.

External 5 V converter on J17. The converter is a purchased module that plugs straight onto the FC through J17, a 1x03 2.54 mm vertical pin header: pin 1 OUT+ (5V_IN), pin 2 GND, pin 3 IN+ (VBAT, raw battery from ESC V via J3.7); the module's EN contact is not connected. Because the converter rides on the board, the stack mounts as one unit, which keeps mounting simple. Its output enters upstream of Q1/D1, never directly at V5_SYS. Set and verify the 5 V output before fitting the module. Its body outline and clearance (including microSD lid access) are not yet verified: the J17 footprint covers the pins only. See the converter review.

Battery current comes from the GOKU G55M ESC's analog C output on J3.1 (R53/C78 → GPIO41/ADC1); VBAT is sensed by R27/R28/C48 on GPIO42/ADC2. The G55M's output scale and offset still need calibration. See G55M sensing.

Design decisions

The reasons behind each major choice are recorded in DESIGN_SPEC.md.

Validating the power input with simulation

The one thing the board cannot control is how power arrives, so that is the one thing simulated. tools/simulate_power_input.py builds an ngspice deck from the saved schematic (it checks the Q1/D1/C19 wiring before running) and drives V5_SYS through seven cases: external 5 V only; USB only; both present; USB plugged in while external stays; USB unplugged; external unplugged; and an external-only load step. The pass criterion is explicit: the lowest V5_SYS seen in any event window must stay above the AP63203's 3.8 V input minimum, or the script exits 1.

sh
python3 tools/simulate_power_input.py                       # default 0.5 A at V5_SYS
python3 tools/simulate_power_input.py --load 0.3 --usb-voltage 4.75
python3 tools/simulate_power_input.py --load 0.5 --external-load 1.0

Latest result (simulations/RESULTS.md): lowest event voltage 4.269 V during USB removal, margin 0.47 V over the floor; USB-only operation settles at 4.32 V through D1. Assumptions are stated, not hidden: 0.05 Ω external source, 0.35 Ω USB source, a 0.5 A combined demand that is a starting point rather than a measured budget, the vendor AO3401A model and a hand-fitted 1N5819WS curve. It does not simulate the downstream regulators, USB negotiation, sensor noise, layout parasitics or temperature — see simulations/README.md for the boundary. Anything beyond the OR is validated on hardware, not in SPICE.

Verifying the design

Requirements: Python 3, KiCad 10 with its standard libraries, ngspice. Ordering exports use the installed Fabrication Toolkit plugin.

sh
mkdir -p build/checks
kicad-cli sch erc --severity-all --exit-code-violations -o build/checks/erc.rpt MARV-V2.kicad_sch
kicad-cli sch export netlist --format kicadxml -o build/checks/netlist.xml MARV-V2.kicad_sch
python3 tools/check_power_netlist.py build/checks/netlist.xml   # rails, all 48 GPIOs, bus endpoints, pull-ups, absent refs
python3 tools/audit_footprints.py build/checks/netlist.xml     # footprint/model availability and pin coverage
kicad-cli pcb drc --schematic-parity --severity-error --severity-warning --format json -o build/checks/drc.json MARV-V2.kicad_pcb

Design rules live in MARV-V2.kicad_pro (board setup) and MARV-V2.kicad_dru (JLCPCB custom rules); edit them in KiCad. Netclasses: Signal 0.10 mm / 0.10 mm clearance (vias 0.45 / 0.30 mm); Default, Rail3V3 and CoreDVDD 0.20 mm; Analog3V3 0.30 mm; Power 0.50 mm (vias 0.80 / 0.40 mm); USB 0.36 mm / 0.18 mm clearance; other vias 0.60 / 0.30 mm. Teardrops are on all vias and pads except the LGA sensors U21, U22 and U23.

Ordering

Rev 1 was ordered from JLCPCB. The exact upload files and every PCB and PCBA option selected are archived in orders/rev1/. To reorder Rev 1, follow that record; it takes precedence over the general steps below.

Use the installed Fabrication Toolkit from KiCad's PCB Editor. Project settings are saved in fabrication-toolkit-options.json; no custom Gerber, BOM or placement exporter is needed.

  1. Open MARV-V2-panel.kicad_pro for the Standard assembly export. This is a saved manufacturing copy with customer-supplied rails. After circuit-design changes, update the original board, synchronize the manufacturing copy, and run the checks before exporting. See the panel notes.

  2. Click Fabrication Toolkit → Generate. The saved options enable automatic component translations and exclude DNP parts. The User.1 V-cut option is on for the manufacturing panel. Automatic zone refill, alternate outlines and plotting all active layers are off. Refill zones yourself in KiCad when copper changes require it, before the final DRC.

  3. Upload the generated files:

    JLCPCB stepFile
    PCB fabricationproduction/MARV-V2-panel.zip (Gerbers and drills with rails)
    Assembly partsproduction/bom.csv
    Assembly placementproduction/positions.csv

These three files were regenerated together from the manufacturing panel on 2026-10-27. The BOM and placements match the final-routed board; the Gerbers include the rails, routed channels, V-score annotations and fiducials; the NPTH drills include tooling holes and the original USB locating holes. The local production/order-manifest.json records source/output SHA-256 hashes, and production/SHA256SUMS checks the three upload files. See the panel verification for validation results and remaining preview checks. Regenerate after any saved design change.

The initial order is 5 PCBs manufactured, 2 assembled on the top side and 3 bare. Select 1 design, Delivery Format: Panel by Customer (1 × 1), 4 layers, 1.6 mm, green mask, white silk, ENIG, standard copper and 0.30 mm minimum via holes. Use Standard assembly and Edge Rails/Fiducials → Added by Customer. The 72 × 72 mm frame contains one finished PCB and uses two full-height V-scores through its side connections, with no mouse-bite holes or added rail silk. It can be removed after delivery; check the quote no longer includes JLC's rail-addition service charge.

The schematic's LCSC fields and native BOM/position exclusions define the assembly selection. J6–J8 and J10 are owner-soldered headers; J3, H1–H4 and the graphic footprints are board features; U24 is DNP. All are omitted from assembly exports. This leaves 90 front-side placements using 34 distinct LCSC parts. The plugin generates one BOM row per component value and note; tools/panel/merge_bom.py merges them to 35 lines (34 LCSC parts plus the J17 line without an LCSC number). JLC's parts-selection page provides current stock and pricing.

Automatic translations apply the plugin's package rotation corrections; they are export corrections, not changes to the PCB layout. Review every placement in JLC's preview, especially the custom sensor footprints and L20: orientation dot toward pad 2 / DVDD. tools/panel/check_positions.py checks the 2026-10-27 export against the source board: all 90 placements match in part and position.

production/ is generated and ignored by Git; use the three plugin files above together. tools/panel/README.md has the exact refresh sequence.

Reports

Decision and review records, newest first:

ReportWhat it records
converter-module-review.mdThe J17 on-board 5 V converter mount, its three-pin interface, battery compatibility and open fit questions
g55m-battery-sensing.mdG55M ESC current and battery sensing connections and limits
manufacturing-panel.mdCustomer-supplied V-cut frame, current order package and panel verification
usb-differential-routing.mdThe 0.36 mm / 0.20 mm gap USB differential-pair preset and the manufacturer guidance behind it
jlc-dfm-routing.mdJLC capability sources behind every installed constraint
sd-connector-replacement.mdThe locking microSD socket (J11): choice, pinout and footprint

Placement and routing are done by hand in KiCad and are never regenerated — see AGENTS.md.

Parts

110
QtyValueFootprintReferences
4M3 grommet hole, 4.0 mm, GND ringMARV_Packages:MountingHole_4.0mm_Grommet_Pad_ViaH1, H2, H3, H4
3Fiducial_1mm_Mask2mmFiducial_1mm_Mask2mmFID1, FID2, FID3
3MountingHole_2mmMountingHole_2mmTOOL1, TOOL2, TOOL3
218p / 50 V C0GCapacitor_SMD:C_0402_1005MetricC46, C47
222u / 6.3 V X5R 0603 CL10A226MQ8NRNC, COUT (DC-bias derated at 3.3 V)Capacitor_SMD:C_0603_1608MetricC10, C11
24.7kResistor_SMD:R_0402_1005MetricR50, R57
25.1k / 1%Resistor_SMD:R_0402_1005MetricR4, R5
1100 / 1%, WS2812 data seriesResistor_SMD:R_0402_1005MetricR55
1100k / 1%, EN to VINResistor_SMD:R_0402_1005MetricR52
1100k / 1%, Q1 gate pull-downResistor_SMD:R_0402_1005MetricR7
1100k / 1%, VBAT topResistor_SMD:R_0402_1005MetricR27
1100k, RUN pull-upResistor_SMD:R_0402_1005MetricR10
1100n / 16 V X7R, ADC0Capacitor_SMD:C_0402_1005MetricC49
1100n / 16 V X7R, ADC1 filterCapacitor_SMD:C_0402_1005MetricC78
1100n / 16 V X7R, ADC2Capacitor_SMD:C_0402_1005MetricC48
1100n / 16 V X7R, ADC_AVDDCapacitor_SMD:C_0402_1005MetricC40
1100n / 16 V X7R, D20 VDDCapacitor_SMD:C_0402_1005MetricC79
1100n / 16 V X7R, DVDD pin 10Capacitor_SMD:C_0402_1005MetricC42
1100n / 16 V X7R, DVDD pin 32Capacitor_SMD:C_0402_1005MetricC43
1100n / 16 V X7R, DVDD pin 51Capacitor_SMD:C_0402_1005MetricC44
1100n / 16 V X7R, IOVDD pin 15Capacitor_SMD:C_0402_1005MetricC31
1100n / 16 V X7R, IOVDD pin 24Capacitor_SMD:C_0402_1005MetricC32
1100n / 16 V X7R, IOVDD pin 29Capacitor_SMD:C_0402_1005MetricC33
1100n / 16 V X7R, IOVDD pin 41Capacitor_SMD:C_0402_1005MetricC34
1100n / 16 V X7R, IOVDD pin 5Capacitor_SMD:C_0402_1005MetricC30
1100n / 16 V X7R, IOVDD pin 50Capacitor_SMD:C_0402_1005MetricC35
1100n / 16 V X7R, IOVDD pin 60Capacitor_SMD:C_0402_1005MetricC36
1100n / 16 V X7R, IOVDD pin 76Capacitor_SMD:C_0402_1005MetricC37
1100n / 16 V X7R, U21 VDDCapacitor_SMD:C_0402_1005MetricC50
1100n / 16 V X7R, U21 VDDIOCapacitor_SMD:C_0402_1005MetricC52
1100n / 16 V X7R, U22 VDDCapacitor_SMD:C_0402_1005MetricC54
1100n / 16 V X7R, U22 VDDIOCapacitor_SMD:C_0402_1005MetricC56
1100n / 16 V X7R, U23 VDDCapacitor_SMD:C_0402_1005MetricC59
1100n / 16 V X7R, U23 VDDIOCapacitor_SMD:C_0402_1005MetricC60
1100n / 16 V X7R, X1 VCCCapacitor_SMD:C_0402_1005MetricC1
1100n / 16 V X7R, at the socketCapacitor_SMD:C_0402_1005MetricC64
1100n / 16 V X7R, bootstrap BST-SW (AP63203 Table 2 C3)Capacitor_SMD:C_0402_1005MetricC13
1100n / 16 V X7R, pins 68+69Capacitor_SMD:C_0402_1005MetricC38
1100u / 6.3 V polymer, ESR <= 40 mOhm (e.g. Panasonic 6TPE100MAZB or KEMET T520/T530 B case), 5V_IN bulk at the pad rowCapacitor_Tantalum_SMD:CP_EIA-3528-21_Kemet-BC19
110k / 1%, VBAT bottomResistor_SMD:R_0402_1005MetricR28
110k / 1%, VBUS topResistor_SMD:R_0402_1005MetricR29
110k, FLASH_CS1 pull-upResistor_SMD:R_0402_1005MetricR35
110k, ICM_CS pull-upResistor_SMD:R_0402_1005MetricR48
110k, IMU2_CS pull-upResistor_SMD:R_0402_1005MetricR51
110k, SD_CMD pull-upResistor_SMD:R_0402_1005MetricR36
110k, SD_DAT0 pull-upResistor_SMD:R_0402_1005MetricR37
110k, SD_DAT1 pull-upResistor_SMD:R_0402_1005MetricR38
110k, SD_DAT2 pull-upResistor_SMD:R_0402_1005MetricR39
110k, SD_DAT3 pull-upResistor_SMD:R_0402_1005MetricR40
110u / 10 V X7R 0603, VIN bulk (AP63203 Table 2 C1)Capacitor_SMD:C_0603_1608MetricC8
110u / 10 V X7R 0603, at the socketCapacitor_SMD:C_0603_1608MetricC65
112 MHz TAXM12M4RFBCCT2T, CL 12 pFCrystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
11521H-32K000J18DTSL 32.000kHzMARV_Packages:Oscillator_SMD_HCI_1521H-4Pin_2.0x1.6mmX1
115k / 1%, VBUS bottomResistor_SMD:R_0402_1005MetricR30
11N5819WSDiode_SMD:D_SOD-323D1
11k / 1%, CURR seriesResistor_SMD:R_0402_1005MetricR53
11k / 1%, USB LED seriesResistor_SMD:R_0402_1005MetricR56
11k / 1%, crystal drive limitResistor_SMD:R_0402_1005MetricR21
11k, BOOTSEL strapResistor_SMD:R_0402_1005MetricR24
11k, ESC telemetry seriesResistor_SMD:R_0402_1005MetricR54
11u / 10 V X7R 0402Capacitor_SMD:C_0402_1005MetricC7
11u / 10 V X7R 0402, LDO inputCapacitor_SMD:C_0402_1005MetricC25
11u / 10 V X7R 0402, U24 VCC (fitted; socket is optional)Capacitor_SMD:C_0402_1005MetricC62
12.2u / 16 V X5R 0603, LDO output (>=1 uF effective, SBVS338H Sec 7.1.1)Capacitor_SMD:C_0603_1608MetricC26
122Resistor_SMD:R_0402_1005MetricR58
122 / 1%, USB D+ seriesResistor_SMD:R_0402_1005MetricR22
122 / 1%, USB D- seriesResistor_SMD:R_0402_1005MetricR23
13.3u, 0806 AOTA-B201610S3R3-101-TInductor_SMD:L_Murata_DFE201610PL20
133 / 1%, VREG_AVDD filterResistor_SMD:R_0402_1005MetricR20
14.7k, MAG SCL pull-upResistor_SMD:R_0402_1005MetricR26
14.7k, MAG SDA pull-upResistor_SMD:R_0402_1005MetricR25
14.7u / 10 V X5R 0402, DVDD bulkCapacitor_SMD:C_0402_1005MetricC45
14.7u / 10 V X5R 0402, DVDD second bulk, far edge of U20 (RP2350 ds 6.3.8.1)Capacitor_SMD:C_0402_1005MetricC81
14.7u / 10 V X5R 0402, VREG_AVDDCapacitor_SMD:C_0402_1005MetricC41
14.7u / 10 V X5R 0402, VREG_VINCapacitor_SMD:C_0402_1005MetricC39
14.7u, Isat 6.0 A (30 %), DCR 46 mOhm max (CJIANG FTC404030S4R7MGCA)MARV_Packages:L_Changjiang_FTC404030SL2
15V converter moduleConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ17
1AO3401APackage_TO_SOT_SMD:SOT-23Q1
1AP63203WU-7Package_TO_SOT_SMD:TSOT-23-6U7
1BMP581 barometerMARV_Packages:Bosch_LGA-10_2x2mm_BMP581U22

The 91 most common of 110 parts.

Similar boards

  • 6 layers55 × 95 mmEcho r1-rev1, the printed circuit board in 3D

    Echo r1-rev1

    amachronic/echoplayer

    Echo - Open Hardware Music Player

    154 parts281CERN-OHL-S-2.0
  • 4 layers88 × 30 mmOled nametag, the printed circuit board in 3D

    Oled nametag

    TobleMiner/oled-nametag

    A ESP32-based OLED nametag

    123 parts54CERN-OHL-P-2.0
  • 4 layers56 × 43.3 mmStepperServoCAN, the printed circuit board in 3D

    StepperServoCAN

    dzid26/StepperServo-hardware

    Stepper actuator controller

    155 parts29GPL-3.0
  • 4 layers107.6 × 59.8 mmTimeDisk, the printed circuit board in 3D

    TimeDisk

    garrettsworkshop/TimeDisk

    Apple II memory expansion card with 1 MB battery-backed RAM and NoSlotClock-compatible clock

    70 parts19
  • 4 layers115.5 × 96.2 mmClosed deck x4, the printed circuit board in 3D

    Closed deck x4

    OpenLogicEFI/Hardware

    Hardware is based off an open source project called Speeduino by Josh Stewart.

    245 parts19
  • 4 layers34.5 × 39 mmEpd watch, the printed circuit board in 3D

    Epd watch

    andr00d/epd_watch

    epd watch project

    63 parts18MIT
  • 4 layers54.7 × 78.5 mmDisplayModule PONSv71, the printed circuit board in 3D

    DisplayModule PONSv71

    MasaoC/GPS-TFT-Map_PONS

    鳥人間コンテストに特化したGNSS誘導システム。人力飛行機のパイロットが使いやすいことを目標にした航法装置です。ハードとソフトをオープンソースで開発しています。

    151 parts14MIT
  • 2 layers74 × 34 mmVhARIO ESPC3, the printed circuit board in 3D

    VhARIO ESPC3

    har-in-air/VhARIO-ESPC3

    Kicad schematic and layout for ESP32-C3 + MPU9250 + MS5611 audio vario

    57 parts13GPL-3.0

Questions

How big is the MARV V2-panel PCB?

It measures 72 × 72 mm and has 4 copper layers, 1.6 mm thick.

What parts does the MARV V2-panel use?

110 parts, built around the 1N5819WS and AO3401A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the MARV V2-panel KiCad files?

From the Lmx154/MARV-V2-PCB repository on GitHub, at the commit this page was made from: the board is MARV-V2-panel.kicad_pcb and its schematic MARV-V2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the MARV V2-panel design in my own project?

Its repository states no licence, so its author keeps all rights: ask Lmx154 before reusing the design.