

Klipper mcu
A custom 3 axis 3d printer
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 37
- Nets
- 89
- Pads
- 177
- Tracks, vias
- 290, 0
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 30 Jun 2026
- Updated
- 25 Oct 2026
Overview
Klipper mcu is an open-source printed circuit board by Kishna-Jain, from the Kishna-Jain/Delarion repository on GitHub. It is a 2-layer board with 37 parts on 89 nets, routed with 290 tracks and 0 vias.
It is built around the ESP32-S3-DEVKITC-1-N8, AMS1117-3.3 and IRLZ44N, with the SK6805E-J among its other parts. Its parts include 7 resistors, 6 diodes, 5 capacitors, 3 ICs and 3 transistors. It belongs with the ESP32 boards of this library.
Main components
4ESP32-S3-DEVKITC-1-N8
-- WiFi Modules ROHSEspressif SystemsWiFi ModulesAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsIRLZ44N
TO-22055V 47A N-Channel HEXFET® Power MOSFETInfineon TechnologiesUncategorisedSK6805E-J
SMD,5.4x5mm-40℃~+85℃ 0.5mA 1.6mm 100mcd~200mcd 100ns 120° 1kHz 2000V 3.7V~5.5V 385mcd~697.5mcd 460nm~470nm 5.4mm 50ns 520nm~535nm 5mm 620nm~625nm 800Kbit/s 80mcd~160mcd 80ns Built-in power-on reset circuit Semi-transparent lens SMD,5.4x5mm RGB LEDs(Built-in IC) ROHSOPSCO OptoelectronicsRGB LEDs(Built-In IC)
README
PCB/README.mdthis pcb was created in Kicad version 10. as you can see in the schematics the XL103 hasnt been mounted on the pcb this is beaacuse of the reason of thermal issues. Adding a high voltage step down convertor produces a lot of heat, which risk damagaing the other components. clean 24volts and 5volts from the step down convertor need to be provided to the designated pins.Use of active cooling is required for the same unless a big explosion is fancied. Heatsnks and proper active cooling should also be applied to the tmc2208/2209 drivers or otherwise damage risk remains high.
A thorough DRC has been ran through there are some errors regarding high power mosfets near signal pins which can meddle with it but i do have added capacitors into the play and kept the mosfet at the back of the board so yeah hopefully all good
Parts
37| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 100uf | Capacitor_SMD:C_0805_2012Metric | C3, C4, C5 |
| 3 | 10k | Resistor_SMD:R_0805_2012Metric | R5, R6, R7 |
| 3 | 1N4007 | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D1, D2, D3 |
| 3 | Conn_01x02_Pin | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | Fan1, Fan2, Fan3 |
| 3 | Conn_01x03_Socket | Connector_JST:JST_XA_B03B-XASK-1_1x03_P2.50mm_Vertical | endstop_x1, endstop_y1, endstop_z1 |
| 3 | IRLZ44N | Package_TO_SOT_THT:TO-220-3_Vertical | Q1, Q2, Q3 |
| 3 | SK6805 | LED_SMD:LED_SK6805_PLCC4_2.4x2.7mm_P1.3mm | D4, D5, D6 |
| 2 | 10uf | Capacitor_SMD:C_0805_2012Metric | C1, C2 |
| 2 | 220ohm | Resistor_SMD:R_0805_2012Metric | R3, R4 |
| 2 | ~ | Custom:TMC2208 | Driver2, UDriver1 |
| 1 | 100uf | Custom:TMC2208 | Driver1 |
| 1 | 220 ohm | Resistor_SMD:R_0805_2012Metric | R2 |
| 1 | 4.7k ohm | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | C | Capacitor_SMD:C_0805_2012Metric | 100nf1 |
| 1 | Conn_01x01_Socket | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J1 |
| 1 | Conn_01x02 | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | Temp_sens1 |
| 1 | Conn_01x02_Socket | Connector_PinSocket_1.00mm:PinSocket_1x02_P1.00mm_Vertical | J2 |
| 1 | ESP32-S3-DevKitC | PCM_Espressif:ESP32-S3-DevKitC | U2 |
| 1 | ~ | Connector_PinSocket_1.00mm:PinSocket_1x08_P1.00mm_Vertical | U3 |
Similar boards
- 4 layers100 × 91.4 mm

- 4 layers81.2 × 81.2 mm

- 2 layers78 × 57 mm

- 4 layers47 × 34 mm

Esp32c3 devboard
tmilkovic51/esp32c3_devboard
A development board integrating the socket for easily swapping the ESP32-C3-WROOM-02 modules, designed in KiCad
72 parts3 - 4 layers58 × 58.8 mm

- 2 layers91 × 80.5 mm

Attention Seeker
M-Mrk/Attention-Seeker
A hackpad with features to alert you to notifications (kde only for now). Zone out alot or focus intensely when doing stuff? You also miss some important notifications? Well me too, so I build this so I can hopefully…
21 parts1Apache-2.0 - 4 layers83.3 × 91.7 mm

TXV2 MAIN revB
Mmessiter/LDRC_V2
LockDown Radio Control V2 — RXV2 receiver and Rotorflight/simulator dongle, the iOS and Android apps, and the TXV2 transmitter. Free and open source.
64 parts1GPL-3.0 - 4 layers100 × 50 mm

Pcm5102a mux board
cbaurtx/RetroBox
RetroBox is an internet radio using an ESP32-S3 system on a chip
86 parts
Questions
What parts does the Klipper mcu use?
37 parts, built around the ESP32-S3-DEVKITC-1-N8, AMS1117-3.3, IRLZ44N and SK6805E-J. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Klipper mcu KiCad files?
From the Kishna-Jain/Delarion repository on GitHub, at the commit this page was made from: the board is PCB/Klipper_mcu.kicad_pcb and its schematic PCB/Klipper_mcu.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Klipper mcu design in my own project?
Its repository states no licence, so its author keeps all rights: ask Kishna-Jain before reusing the design.