

Humidity
This is an experimental pcb design for a battery powered wireless humidity, temperature, and pressure sensor. It uses an esp32 wifi chip along with a bme280 sensor.
- Size
- 59.7 × 27.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 16
- Nets
- 37
- Pads
- 100
- Tracks, vias
- 238, 39
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 27 Dec 2019
- Updated
- 9 Feb 2022
Overview
Humidity is an open-source printed circuit board by KevinOConnor, from the KevinOConnor/humidwifi repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 59.7 × 27.9 mm with 16 parts on 37 nets, routed with 238 tracks and 39 vias.
It is built around the ESP32-WROOM-32 and BME280. Its parts include 5 capacitors, 4 resistors, 3 connectors, 2 ICs and 1 diode. It belongs with the ESP32 boards of this library.
Main components
2ESP32-WROOM-32
SMD,18x25.5mm-40℃~+85℃ -98dBm 2.4GHz 2.7V~3.6V 20dBm Bluetooth4.2 ESP32-DOWDQ6 UART、SDIO、SPI、I2C、GPIO、PWM、ADC、DAC SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesBME280
LGA-8(2.5x2.5)-40℃~+85℃ 0%RH~100%RH 1.71V~3.6V 1.8uA 16bit I2C、SPI ±0.5℃ ±3%RH LGA-8(2.5x2.5) Temperature and Humidity Sensor ROHSBoschTemperature And Humidity Sensor
README
README.mdThis is an experimental pcb design for a battery powered wireless humidity, temperature, and pressure sensor. It uses an esp32 wifi chip along with a bme280 sensor.
This is an experiment. There is no support for this project.



There is some information on the pcb design in the pcb document.
There is some information on building the firmware in the firmware document.
Parts
16| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 100nF | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3 |
| 2 | 4K7 | Resistor_SMD:R_0402_1005Metric | R2, R3 |
| 1 | 0K1 | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 100nF | Capacitor_SMD:C_0805_2012Metric | C5 |
| 1 | 10K | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C4 |
| 1 | BME280 | Package_LGA:Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumbering | U1 |
| 1 | Battery Holder | Battery:BatteryHolder_Keystone_2460_1xAA | J1 |
| 1 | Conn_01x09 | Connector_PinHeader_2.54mm:PinHeader_1x09_P2.54mm_Vertical | J2 |
| 1 | Conn_02x09_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x09_P2.54mm_Vertical | J3 |
| 1 | ESP32-WROOM-32 | RF_Module:ESP32-WROOM-32 | U2 |
| 1 | Red LED | LED_SMD:LED_0805_2012Metric | D1 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_TL3342 | SW1 |
Similar boards
- 2 layers110 × 90 mm

- 2 layers100 × 100 mm

SmartSolarHeatingProject
UnknownHero99/SmartSolarHeatingProject
ESP32 based Smart Solar Heating Project
63 parts5 - 2 layers186.7 × 81.8 mm

DD Scope PCBv3
RichardBenear/DDScopeX-Hardware
Hardware documentation for Direct Drive Scope
85 parts3MIT - 2 layers70 × 33 mm

- 2 layers

Unplugged
Kalash4152/smart-dustbin-round-two
Designed and simulated a Smart Dustbin & Smart Traffic Lights system using Arduino, ESP32, and sensors at DJSCE Unplugged 2.0.
24 parts1 - 2 layers

- 2 layers80 × 60 mm

- 2 layers52.8 × 65.3 mm

Questions
How big is the Humidity PCB?
It measures 59.7 × 27.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Humidity use?
16 parts, built around the ESP32-WROOM-32 and BME280. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Humidity KiCad files?
From the KevinOConnor/humidwifi repository on GitHub, at the commit this page was made from: the board is pcb/humidity.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Humidity design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).