

Rapiduino
A line follower robot
- Size
- 99.1 × 92.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 64
- Nets
- 45
- Pads
- 142
- Tracks, vias
- 173, 33
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 16 Aug 2026
- Updated
- 5 Nov 2026
Overview
Rapiduino is an open-source printed circuit board by KBZoNiX, from the KBZoNiX/zopapa repository on GitHub, published under the MIT licence. It is a 2-layer board of 99.1 × 92.1 mm with 64 parts on 45 nets, routed with 173 tracks and 33 vias.
It is built around the IRLR2905. Its parts include 10 connectors, 6 resistors, 4 diodes, 3 capacitors and 3 switches. It belongs with the robots and motor control boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
1README
README.mdZopapa
A two-wheel differential-drive line-following robot: Arduino Nano firmware, an 8-channel reflectance sensor array, and two custom KiCad PCBs.
Full functional specification: docs/FSD.html · User manual (Spanish): docs/MANUAL.html
Features
- PD line-following control loop (proportional + derivative, ~500 Hz)
- Relay-feedback (Åström–Hägglund) autotune — computes and installs new gains from an induced oscillation
- EEPROM persistence of tuned speed/gains and sensor calibration — no need to re-sweep the line sensor on every power-cycle
- Serial/Bluetooth command interface for live tuning and telemetry (shared UART, 9600 baud)
- Optional turbine/vacuum subsystem for extra downforce, ramped proportionally to steering correction
- On-board HMI: pushbutton (short press starts/stops; long press saves gains to EEPROM or recalibrates the sensor, depending on DIP 4 — see FSD §7.1), 4-position DIP bank, status LED, buzzer
Repo layout
src/zopapa/ Arduino sketch (zopapa.ino is the entry point)
src/libraries/ Vendored first-party libraries: DRV8833 (motor driver), ATRSensors (line sensor)
hardware/ KiCad PCB projects — main_pcb (Rapiduino) and line_sensor_pcb (ATR-8A)
docs/FSD.html Functional Specification Document
docs/MANUAL.html User manual (Spanish) — physical controls and BT/Serial commandsBuild
Requires arduino-cli with the arduino:avr core installed.
arduino-cli compile --fqbn arduino:avr:nano --libraries src/libraries src/zopapaArduino IDE: open src/zopapa/zopapa.ino directly, and copy or symlink src/libraries/* into your sketchbook's libraries/ folder first.
Flash
Most Nano (and clone) boards need the old-bootloader CPU variant:
arduino-cli compile --fqbn arduino:avr:nano:cpu=atmega328old --libraries src/libraries -u -p /dev/ttyUSB0 src/zopapaIf uploads fail with repeated not in sync errors, that's this — try the atmega328old variant. Requires your account to be in the dialout group (Linux).
Command interface
Sent over Serial or Bluetooth (same UART, 9600 baud):
| Command | Function | Example |
|---|---|---|
S | Start | S |
P | Stop | P |
T | Run autotune | T |
Vxxx | Set speed | V180 |
Kxxx | Set KP | K22.5 |
Dxxx | Set KD | D15.3 |
R | Read current parameters | R |
L | Load parameters from EEPROM | L |
W | Save parameters to EEPROM | W |
Q | Live sensor bar test | Q |
C | Force a fresh sensor calibration sweep, then save it | C |
H | Help | H |
See docs/FSD.html for the full electrical interconnect, BOM, control-loop math, and known quirks.
Notes
- Firmware comments and Serial output are in Spanish.
- No test suite.
License
MIT, except src/libraries/ATRSensors, which retains the CC BY-SA 3.0 notice of the Pololu QTRSensors code it's derived from (see the file header).
Parts
64| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 470 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R3, R4 |
| 3 | LED | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D3, D5, D12 |
| 2 | G*** | kibuzzard-6850F7E0 | kibuzzard-6850F7E0, kibuzzard-6850F7E0 |
| 2 | G*** | kibuzzard-6850F811 | kibuzzard-6850F811, kibuzzard-6850F811 |
| 1 | 100 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 1 | 100uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C2 |
| 1 | 10uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C3 |
| 1 | 1K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5 |
| 1 | 1N4007 | Diode_THT:D_DO-41_SOD81_P7.62mm_Horizontal | D1 |
| 1 | 220uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C1 |
| 1 | 2K2 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6 |
| 1 | Arduino_Nano_v2.x | Module:Arduino_Nano | A1 |
| 1 | BATT | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | Bluetooth | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J5 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | Conn_sensores | Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_Vertical | J6 |
| 1 | G*** | kibuzzard-685246CF | kibuzzard-685246CF |
| 1 | G*** | kibuzzard-685108F3 | kibuzzard-685108F3 |
| 1 | G*** | kibuzzard-685101AF | kibuzzard-685101AF |
| 1 | G*** | kibuzzard-6850FB4B | kibuzzard-6850FB4B |
| 1 | G*** | kibuzzard-685245CF | kibuzzard-685245CF |
| 1 | G*** | kibuzzard-68523F1B | kibuzzard-68523F1B |
| 1 | G*** | kibuzzard-6850F8CB | kibuzzard-6850F8CB |
| 1 | G*** | kibuzzard-685232D8 | kibuzzard-685232D8 |
| 1 | G*** | kibuzzard-685108A6 | kibuzzard-685108A6 |
| 1 | G*** | kibuzzard-685241D4 | kibuzzard-685241D4 |
| 1 | G*** | kibuzzard-6852314D | kibuzzard-6852314D |
| 1 | G*** | kibuzzard-6850FB1B | kibuzzard-6850FB1B |
| 1 | IRLR2905 | Package_TO_SOT_SMD:TO-252-2 | Q1 |
| 1 | Jumper_alimentación_Arduino | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J10 |
| 1 | LOGO | Graphics:club-robotica-logo_32x32mm | G*** |
| 1 | LOGO | Graphics:club-robotica-icon_14x14mm | G*** |
| 1 | LOGO | Graphics:USB-connector-drawing-8mm | G*** |
| 1 | LOGO | Graphics:Bluetooth-logo-10x5mm | G*** |
| 1 | Motor A | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J8 |
| 1 | Motor B | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J9 |
| 1 | SW_DIP_x04 | Button_Switch_THT:SW_DIP_SPSTx04_Slide_9.78x12.34mm_W7.62mm_P2.54mm | SW3 |
| 1 | SW_Power | Custom_Packages:SW_Push_2P2T_Toggle_7x7mm | SW1 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_6mm | SW2 |
| 1 | Start | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J7 |
| 1 | TB6612FNG Driver Module | Custom_Packages:TB6612FNG Driver Module | A2 |
| 1 | Vboost_in | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | Vboost_out | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | turbina | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
The 50 most common of 64 parts.
More from KBZoNiX/zopapa
1- 2 layers75.6 × 15.2 mm

Similar boards
- 2 layers42 × 45.1 mm

ESP8266 LED controller
daumemo/DIY-ESP-12E-LED-Strip-Controller-4-Channel
DIY LEd Strip Controller with ESP-12E
31 parts5GPL-3.0 - 2 layers44.5 × 37.9 mm

PetPull v3
Fremen72/MiniPetPull
Recycler PET plastic bottles into filament for 3D printer
14 partsGPL-3.0 - 2 layers78.3 × 50 mm

Doz 030
pavlig43/Doz_stm32f103CBTx
Рабочий проект — doz030.kicadpro в этой папке. Открывайте его в KiCad 10. Схема, плата и настройки проекта хранятся в одном Git-репозитории с прошивкой.
35 parts - 4 layers240 × 180 mm

- 2 layers210 × 145 mm

- 2 layers36 × 20 mm

- 2 layers99.1 × 92.7 mm

Controller
dario0603/Hotplate
Hotplate is a DIY electronics project focused on the design and development of a hotplate and its associated control electronics.
100 parts - 2 layers42 × 32 mm

Questions
How big is the Rapiduino PCB?
It measures 99.1 × 92.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Rapiduino use?
64 parts, built around the IRLR2905. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Rapiduino KiCad files?
From the KBZoNiX/zopapa repository on GitHub, at the commit this page was made from: the board is hardware/main_pcb/Rapiduino.kicad_pcb and its schematic hardware/line_sensor_pcb/ATR-8A.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Rapiduino design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).