

Raspberry pi hat
References: - Connecting power button: https://howchoo.com/pi/how-to-add-a-power-button-to-your-raspberry-pi/ - Connecting decoupling capacitor: https://www.mysensors.org/build/connectradio - Connections between module…
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 14
- Nets
- 34
- Pads
- 130
- Tracks, vias
- 70, 2
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 26 Sep 2024
- Updated
- 19 Dec 2024
Overview
Raspberry pi hat is an open-source printed circuit board by Juliandavidquintero, from the Juliandavidquintero/MTP_PCB_TEAM_A repository on GitHub. It is a 2-layer board with 14 parts on 34 nets, routed with 70 tracks and 2 vias.
It is built around the NRF24L01P-R and LM3940IT-3.3. Its parts include 5 resistors, 5 connectors, 2 capacitors and 2 ICs.
Main components
2NRF24L01P-R
QFN-20-EP(4x4)-40℃~+85℃ -82dBm 0dBm 1.9V~3.6V 11.3mA 13.5mA 2.4GHz 2.4GHz~2.525GHz 2Mbps ISM Power-on reset function、Supports RSSI function、CRC check function、Automatic response function、Automatic retransmission function SPI transceiver QFN-20-EP(4x4) RF Transceiver ICs ROHSNordic SemiconRF Transceiver ICsLM3940IT-3.3
TO-220-40℃~+125℃ 1 10mA 150uVrms 1A 200mV@(100mA) 3.3V 7.5V Fixed Over Temperature Protection、Short Circuit Protection Positive TO-220 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsLinear Voltage Regulators (LDO)
README
README.mdReferences:
- Connecting power button: https://howchoo.com/pi/how-to-add-a-power-button-to-your-raspberry-pi/
- Connecting decoupling capacitor: https://www.mysensors.org/build/connect_radio
- Connections between module and Raspi: https://forum.mysensors.org/topic/2437/step-by-step-procedure-to-connect-the-nrf24l01-to-the-gpio-pins-and-use-the-raspberry-as-a-serial-gateway-mysensors-1-x https://lastminuteengineers.com/nrf24l01-arduino-wireless-communication/
Parts
14| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 220 | Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R1, R2, R3, R4, R5 |
| 2 | GPIO | Module:Raspberry_Pi_Zero_Socketed_THT_FaceDown_MountingHoles | J1, J6 |
| 1 | 0,47uF | Capacitor_THT:C_Radial_D4.0mm_H5.0mm_P1.50mm | C1 |
| 1 | 33uF | Capacitor_THT:C_Radial_D4.0mm_H5.0mm_P1.50mm | C2 |
| 1 | LCD_screeen | Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_Vertical | J5 |
| 1 | LED_status | Connector_Molex:Molex_KK-254_AE-6410-06A_1x06_P2.54mm_Vertical | J8 |
| 1 | LM3940IT | Package_TO_SOT_THT:TO-220-3_Horizontal_TabDown | IC1 |
| 1 | NRF24L01P | NRF24L01P-MODULE-PCB:XCVR_NRF24L01P-MODULE-PCB | U3 |
| 1 | Switches | Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_Vertical | J7 |
Similar boards
- 2 layers136.8 × 87 mm

- 2 layers140 × 90 mm

Rib
illinoistechrobotics/rib
The Illinois Tech Robotics RIB is a custom PCB used to control our robots of all sizes.
96 parts4 - 2 layers

Board withoutEncoder prev
DaniMzT/MonitoringSensorsAutomaticDoor
Monitoring sensors of an automated door (it can be extended to generic systems). University project
37 parts - 2 layers52.5 × 62.1 mm

- 2 layers

- 4 layers40 × 50 mm

- 4 layers61.8 × 27.5 mm

Audio Processing HW V1.0
aitesam961/OpenADSP
An Embedded Digital Signal Processing Device for Audio signals.
83 parts4GPL-3.0 - 2 layers40.6 × 78.5 mm

Brooklyn
ARTS-Laboratory/DOVE
DOVE: Dynamics Observation and Vibration at the Edge. A deployable sensor package for vibration-based structural health monitoring.
39 parts4CC-BY-SA-4.0
Questions
What parts does the Raspberry pi hat use?
14 parts, built around the NRF24L01P-R and LM3940IT-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Raspberry pi hat KiCad files?
From the Juliandavidquintero/MTP_PCB_TEAM_A repository on GitHub, at the commit this page was made from: the board is raspberry_pi_hat/raspberry_pi_hat.kicad_pcb and its schematic raspberry_pi_hat/raspberry_pi_hat.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Raspberry pi hat design in my own project?
Its repository states no licence, so its author keeps all rights: ask Juliandavidquintero before reusing the design.