Skip to the content
4 layers66 × 142 mmHandset, the printed circuit board in 3D

OWASSO-1 DIY ESP32-S3 phone KiCad revF PCB project

Size
66 × 142 mm
Copper layers
4
Thickness
1.6 mm
Parts
242
Nets
254
Pads
1,044
Tracks, vias
1,278, 146
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
21 Sep 2026
Updated
26 Oct 2026

Overview

Handset is an open-source printed circuit board by JeremyLakeyJr, from the JeremyLakeyJr/mesh-phone repository on GitHub, published under the MIT licence. It is a 4-layer board of 66 × 142 mm with 242 parts on 254 nets, routed with 1,278 tracks and 146 vias.

It is built around the CC1101RGPR, DM3D-SF and TPD4E05U06DQAR, with the BQ25186DLHR, AO3400A and LQW15AN12NJ00D among its other parts. Its parts include 79 capacitors, 61 resistors, 16 switches, 8 transistors and 8 inductors.

Main components

12

README

hardware/rev-f/README.md

Owasso1 Rev F — engineering checkpoint, not a fabrication release

Open mesh-phone.kicad_pro in this directory. The project in ../main/ is the preserved original, not this corrected revision.

Implemented in schematic and PCB:

  • MAX-M10S GPS with passive-antenna U.FL, UART, PPS and bypass capacitors.
  • Rear keyed 10-pin JST-GH expansion interface, with a current-limited 3.3 V supply and shared SPI/I²C. Switch off and disconnect USB before swapping.
  • MCU EN/BOOT support, usable SPI pin assignments, keypad expander pin-order corrections, display controls and I²C pull-ups.
  • Removal of the switch connection that directly joined USB 5 V to the battery.
  • Reconciled schematic/PCB pad contracts, with original component placements preserved. New parts are rear-mounted.

Read INTERFACES.md before designing a module. This is a keyed cable connector, not a finished blind-mate mechanical docking system.

Not safe to order or power yet

The inherited battery protection, charger/power path, 3.3 V regulator and 5 V boost circuits still require redesign. The A7670E modem/carrier is not approved for the US target. Remaining radio-control, IR, fuel-gauge, RFID and SIM interfaces are incomplete. See the full connection review.

RF/USB impedance and antenna/enclosure placement are unverified. Ground vias at the new reset circuitry overlap solderable pads; move them outside pads or specify a suitable filled/capped via process during the final DFM pass. Do not assume ordinary open vias in solder pads are assembly-ready.

Verification evidence

Latest checkpoint: 608/608 contract and placement checks passed. Native KiCad DRC reports 0 errors, 0 unconnected items and 0 schematic-parity findings, with 5 footprint-library mismatch warnings. ERC still reports 2 errors and 24 warnings from unresolved supply modelling and interfaces. The five footprint warnings concern J10, USB1, U1, J14 and J3; their modified pad/geometry contracts need final library and manufacturer-drawing review.

  • verification-summary.json: independent net/placement checks, native tool counts and SHA-256 fingerprints of the checked files.
  • drc-final.json: native KiCad DRC, including schematic parity.
  • erc.json: unresolved electrical-rule findings, not waived with power flags.
  • owasso1-engineering.pdf: two-sheet schematic for review.
  • previews/: schematic SVGs.

Zero routing errors would not certify circuit operation. Firmware, bench bring-up, battery-safety verification, RF tests and cellular carrier acceptance are still required. No revised manufacturing package has been released.

To repeat the read-only contract checks, run python scripts/verify_revF.py from the repository root after exporting a fresh netlist.xml. The build/routing and layout experiment scripts in ../../archive/scripts/ are checkpoint tools, not an idempotent pipeline: do not replay them on this finished checkpoint.

Parts

242
QtyValueFootprintReferences
15100nFCapacitor_SMD:C_0402_1005MetricC3, C4, C10, C13, C15, C23, C24, C29, C31, C40, C42, C45, C46, C47, C55
14100nF 10% X7R 16VCapacitor_SMD:C_0402_1005MetricC8, C11, C12, C69, C70, C71, C72, C73, C75, C76, C79, C81, C82, C83
12100kResistor_SMD:R_0402_1005MetricR6, R8, R13, R30, R33, R42, R47, R50, R51, R57, R64, R67
1010kResistor_SMD:R_0402_1005MetricR1, R2, R5, R10, R12, R40, R58, R59, R66, R69
810uFCapacitor_SMD:C_0805_2012MetricC2, C14, C20, C25, C28, C41, C43, C49
733Resistor_SMD:R_0402_1005MetricR20, R21, R22, R23, R24, R25, R26
7AO3400APackage_TO_SOT_SMD:SOT-23Q1, Q2, Q3, Q4, Q5, Q7, Q8
6100k 1%Resistor_SMD:R_0402_1005MetricR32, R35, R41, R61, R63, R65
54.7kResistor_SMD:R_0402_1005MetricR3, R4, R7, R68, R70
412nH 5%Inductor_SMD:L_0402_1005MetricL5, L6, L9, L10
4150 1% 0.1WResistor_SMD:R_0603_1608MetricR52, R53, R54, R55
41uFCapacitor_SMD:C_0402_1005MetricC1, C30, C37, C44
42.2uFCapacitor_SMD:C_0603_1608MetricC32, C33, C34, C35
4MountingHole_2.2mm_M2MountingHole_2.2mm_M2H1, H2, H3, H4
3100Resistor_SMD:R_0402_1005MetricR46, R49, R56
310k 1%Resistor_SMD:R_0402_1005MetricR76, R77, R78
322uFCapacitor_SMD:C_0805_2012MetricC21, C22, C26
322uF 10V X5RCapacitor_SMD:C_0805_2012MetricC52, C53, C54
34.7uF 10% X5R 25VCapacitor_SMD:C_0603_1608MetricC77, C78, C80
347kResistor_SMD:R_0402_1005MetricR43, R44, R45
3TPD4E05U06DQARPackage_SON:USON-10_2.5x1.0mm_P0.5mmU15, U16, U17
2046701.5NRHF / 1.5AFuse:Fuse_0603_1608MetricF1, F2
21.5pF 0.25pF C0G 50VCapacitor_SMD:C_0402_1005MetricC64, C68
2100nF 10V X7RCapacitor_SMD:C_0402_1005MetricC58, C60
2100nF 50V X7RCapacitor_SMD:C_0603_1608MetricC56, C59
210uF 10V X7RCapacitor_SMD:C_0805_2012MetricC50, C51
215pF 5% C0G 50VCapacitor_SMD:C_0402_1005MetricC61, C62
218nH 5%Inductor_SMD:L_0402_1005MetricL7, L8
227pF C0GCapacitor_SMD:C_0402_1005MetricC38, C39
24.7uFCapacitor_SMD:C_0603_1608MetricC27, C48
11Button_Switch_SMD:SW_SPST_TL3342SW1
110Button_Switch_SMD:SW_SPST_TL3342SW10
1100pF 5% C0G 50VCapacitor_SMD:C_0402_1005MetricC66
110nFCapacitor_SMD:C_0402_1005MetricC36
110uF 25V X5RCapacitor_SMD:C_0805_2012MetricC6
111Button_Switch_SMD:SW_SPST_TL3342SW11
112Button_Switch_SMD:SW_SPST_TL3342SW12
112pF 5% C0G 50VCapacitor_SMD:C_0402_1005MetricC67
113Button_Switch_SMD:SW_SPST_TL3342SW13
114Button_Switch_SMD:SW_SPST_TL3342SW14
115Button_Switch_SMD:SW_SPST_TL3342SW15
115uH 20%Inductor_SMD:L_TDK_MLZ2012_h1.25mmL12
116Button_Switch_SMD:SW_SPST_TL3342SW16
11kohm @100MHzInductor_SMD:L_0402_1005MetricL11
11pF 0.25pF C0G 50VCapacitor_SMD:C_0402_1005MetricC63
11uF 10% X5R 10VCapacitor_SMD:C_0402_1005MetricC74
12Button_Switch_SMD:SW_SPST_TL3342SW2
12.2uF 10V X7RCapacitor_SMD:C_0603_1608MetricC57
12.2uF 25V X7RCapacitor_SMD:C_0805_2012MetricC5
126MHz CL10pFHandset:ABM8_3225Y2
13Button_Switch_SMD:SW_SPST_TL3342SW3
13.3pF 0.25pF C0G 50VCapacitor_SMD:C_0402_1005MetricC65
1374k 1%Resistor_SMD:R_0402_1005MetricR60
1390k 1%Resistor_SMD:R_0402_1005MetricR62
14Button_Switch_SMD:SW_SPST_TL3342SW4
14.7k 1%Resistor_SMD:R_0402_1005MetricR79
14.7uF 10V X7RCapacitor_SMD:C_0603_1608MetricC7
147 1% 0.125WResistor_SMD:R_0805_2012MetricR48
1470nF 10% X5R 10VCapacitor_SMD:C_0402_1005MetricC9
15Button_Switch_SMD:SW_SPST_TL3342SW5
1560k 1%Resistor_SMD:R_0402_1005MetricR31
156k 1%Resistor_SMD:R_0402_1005MetricR11
16Button_Switch_SMD:SW_SPST_TL3342SW6
17Button_Switch_SMD:SW_SPST_TL3342SW7
1732k 1%Resistor_SMD:R_0402_1005MetricR34
18Button_Switch_SMD:SW_SPST_TL3342SW8
1887k 1%Resistor_SMD:R_0402_1005MetricR9
19Button_Switch_SMD:SW_SPST_TL3342SW9
1ABM8-27.120MHZ-B2-TCrystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
1AO3401APackage_TO_SOT_SMD:SOT-23Q6
1BAT54C,215Package_TO_SOT_SMD:SOT-23D2
1BATTERY_POLARITY_VERIFYConnector_JST:JST_PH_B2B-PH-SM4-TB_1x02-1MP_P2.00mm_VerticalJ1
1BQ25186DLHRPackage_DFN_QFN:Texas_DLH0010A_WSON-10-1EP_2.2x2mm_P0.4mm_EP0.9x1.5mmU3
1CALL_AUDIO_FROM_MODEM_ADAPTERConnector_JST:JST_GH_BM04B-GHS-TBT_1x04-1MP_P1.25mm_VerticalJ4
1CALL_EARPIECEConnector_JST:JST_GH_BM02B-GHS-TBT_1x02-1MP_P1.25mm_VerticalJ5
1CALL_MICConnector_JST:JST_GH_BM02B-GHS-TBT_1x02-1MP_P1.25mm_VerticalJ6
1CC1101RGPRPackage_DFN_QFN:Texas_RGP0020D_VQFN-20-1EP_4x4mm_P0.5mm_EP2.7x2.7mmU5
1CC1101_915_ANTConnector_Coaxial:U.FL_Hirose_U.FL-R-SMT-1_VerticalJ21
1CC_GDO2_TESTTestPoint:TestPoint_Pad_D1.0mmTP1
1DM3D-SFConnector_Card:microSD_HC_Hirose_DM3D-SFJ23

The 193 most common of 242 parts.

More from JeremyLakeyJr/mesh-phone

5
  • 4 layers66 × 142 mmHandset, the printed circuit board in 3D

    Handset

    JeremyLakeyJr/mesh-phone

    OWASSO-1 DIY ESP32-S3 phone KiCad revF PCB project

    174 partsMIT
  • 4 layers66 × 142 mmHandset, the printed circuit board in 3D

    Handset

    JeremyLakeyJr/mesh-phone

    OWASSO-1 DIY ESP32-S3 phone KiCad revF PCB project

    146 partsMIT
  • 4 layers66 × 142 mmHandset, the printed circuit board in 3D

    Handset

    JeremyLakeyJr/mesh-phone

    OWASSO-1 DIY ESP32-S3 phone KiCad revF PCB project

    106 partsMIT

Similar boards

  • 6 layers58.4 × 156.2 mmLAUNCHXL F280049C KICAD, the printed circuit board in 3D

    LAUNCHXL F280049C KICAD

    MiniNugen/Custom_Inverter_Hardware

    PCBProjectNameREV1.PrjPCB | Source Documents | | PCBProjectNameREV1.SchDOC | | PCBProjectNameREV1.PcbDOC | | BOM | Settings | Libraries

    237 parts1
  • 4 layers96 × 70 mmTradewind, the printed circuit board in 3D

    Tradewind

    binaryBeachLLC/tradewind

    Tradewind TW-1: solar LoRaWAN field sensor. KiCad 9 board, CadQuery enclosure, RUI3 firmware, simulations, test data, report and datasheet.

    85 parts
  • 4 layers64 × 56 mmAlec sensor, the printed circuit board in 3D

    Alec sensor

    eshelton328/forge

    Hardware design monorepo with software-grade CI/CD. KiCad PCB projects with automated ERC/DRC, multi-fab rule validation, schematic & BOM checks, and auto-generated board documentation.

    100 parts
  • 4 layers30 × 40.8 mmDrone fc, the printed circuit board in 3D

    Drone fc

    neilpate/Drone

    A learning project: build a quadcopter from scratch — own hardware, own firmware, no existing flight stack.

    37 partsApache-2.0
  • 4 layers63.5 × 26.1 mmBwlr1f, the printed circuit board in 3D

    Bwlr1f

    teapotlaboratories/bwlr1f

    69 parts
  • 4 layers68.3 × 55.7 mmEEG32, the printed circuit board in 3D

    EEG32

    Iwetter/EEG32

    32-channel ADS1299/nRF52832 acquisition board design in KiCad, with schematics, PCB layout, BOM, and pre-fabrication documentation. Bench tests pending.

    225 parts1
  • 2 layers20.8 × 34.8 mmCarrier, the printed circuit board in 3D

    Carrier

    5haman/especcy

    Thumb-sized ESP32 ZX Spectrum handheld, 24 × 38 × 12 mm: FreeCAD enclosure, KiCad carrier study and cycle-timed 48K emulator firmware.

    21 partsGPL-3.0

Questions

How big is the Handset PCB?

It measures 66 × 142 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Handset use?

242 parts, built around the CC1101RGPR, DM3D-SF, TPD4E05U06DQAR and BQ25186DLHR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Handset KiCad files?

From the JeremyLakeyJr/mesh-phone repository on GitHub, at the commit this page was made from: the board is archive/handset-before-main-distribution/947efb32e5ff/handset.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Handset design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).