Skip to the content
4 layers21.3 × 33.4 mmFull route, the printed circuit board in 3D

Arduino Pro Micro / GoldFish compatible AtMega32U4 for JLCPCB assembly

Size
21.3 × 33.4 mm
Copper layers
4
Thickness
1.6 mm
Parts
25
Nets
43
Pads
150
Tracks, vias
436, 70
Pours
5
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
26 Nov 2020
Updated
12 Apr 2021

Overview

Full route is an open-source printed circuit board by JeremyJStarcher, from the JeremyJStarcher/Goldfish-clone-JLCPCB repository on GitHub. It is a 4-layer board of 21.3 × 33.4 mm with 25 parts on 43 nets, routed with 436 tracks and 70 vias.

It is built around the ATMEGA32U4. Its parts include 10 capacitors, 8 resistors, 3 connectors, 1 IC and 1 diode. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

Goldfish-clone-JLCPCB

This board is a new layout for the original Goldfish by Lucas Jansen.

REV A has several design issues that make it very difficult to attach the USB connector.

Do not use!

Why?

This board was designed to be used with JLCPCB's SMD assembly service. Because JLCPCB has very different requirements, the board layout needed redesigned entirely.

Important changes

  • Four layer board with separate ground and power layers. No additional charge, so why not?
  • Board is wider to meet the minimum width requirements
  • The board is longer to allow top-side labels all the way around
  • Changed the USB connector to one that is more easily soldered by hand at the cost of making the board slightly thicker.
  • Changed the crystal to match parts available.
  • 0 Ohm resisters added to help USB data signal routing
  • Additional USB Datapins removed.

License Information

Released under the Creative Commons Attribution Share-Alike 4.0 License.
https://creativecommons.org/licenses/by-sa/4.0/

Original Arduino Mini Design by Team Arduino.
Arduino Pro Mini Design by Spark Fun Electronics.
Pro Micro Design by Spark Fun Electronics.
Goldfish Design by Dr Derivative.
JLCPCB assembly version by Jeremy J Starcher

Revision History

  • Rev A - Initial release. On order - untested.

Parts

25
QtyValueFootprintReferences
60u1Capacitor_SMD:C_0402_1005MetricC1, C2, C3, C4, C5, C10
201x12pins:Pins12J3, J4
20RResistor_SMD:R_0603_1608MetricR7, R8
210kResistor_SMD:R_0402_1005MetricR3, R6
222Resistor_SMD:R_0402_1005MetricR4, R5
222pCapacitor_SMD:C_0402_1005MetricC7, C8
25k1Resistor_SMD:R_0402_1005MetricR1, R2
101x05pins:Pins5J5
116MHzCrystal:Crystal_SMD_SeikoEpson_TSX3225-4Pin_3.2x2.5mmX1
11uCapacitor_SMD:C_0402_1005MetricC9
14u7Capacitor_SMD:C_0402_1005MetricC6
1ATmega32U4Package_DFN_QFN:QFN-44-1EP_7x7mm_P0.5mm_EP5.2x5.2mmU1
1CLEAN-TYPE-C-31-M-12Type-C:HRO-TYPE-C-31-M-12-HandSolderingUSB1
1D_SchottkyDiode_SMD:D_PowerDI-123D1

More from JeremyJStarcher/Goldfish-clone-JLCPCB

1
  • 2 layers21.3 × 33.9 mmGoldfish, the printed circuit board in 3D

    Goldfish

    JeremyJStarcher/Goldfish-clone-JLCPCB

    Arduino Pro Micro / GoldFish compatible AtMega32U4 for JLCPCB assembly

    25 parts21

Similar boards

  • 2 layers89 × 100 mmHub16, the printed circuit board in 3D

    Hub16

    joshajohnson/Hub16

    A macro pad with 16 keys, two rotary encoders, a four port USB hub, and plenty of LEDs!

    132 parts388
  • 2 layers22.9 × 36.7 mmUsb2usb, the printed circuit board in 3D

    Usb2usb

    tmk/USB2USB_Converter

    USB to USB keyboard protocol converter supported by TMK keyboard firmware

    26 parts152
  • 2 layers303.6 × 96.1 mmKyuu, the printed circuit board in 3D

    Kyuu

    Quantrik/Kyuu

    Kyuu Keyboard Design

    154 parts127
  • 2 layers114.9 × 77 mmTestProject, the printed circuit board in 3D

    TestProject

    Quarren42/SPIN

    12 key, 3 encoder USB-C Macro Pad

    117 parts104CC-BY-SA-4.0
  • 2 layers444.1 × 151.2 mmGh80-3003, the printed circuit board in 3D

    Gh80-3003

    evyd13/gh80-series

    GH80-1800, GH80-3700 and GH80-3003 by Evy (aka anykeys.eu)

    287 parts69CC-BY-SA-4.0
  • 2 layers232.2 × 76.7 mmCpm43, the printed circuit board in 3D

    Cpm43

    Gtrx0/cpm43

    40% mechanical keyboard with rgb underglow and single color backlight

    188 parts59
  • 2 layers373.2 × 131.8 mmNt980, the printed circuit board in 3D

    Nt980

    evyd13/nt-series

    Replacement PCBs for the FC660m, FC750r and FC980m.

    242 parts56CC-BY-SA-4.0
  • 2 layers17.8 × 33 mmAlvaro, the printed circuit board in 3D

    Alvaro

    Kaleidogeist/Alvaro

    Pro Micro-compatible 32u4 Breakout Board

    28 parts53Apache-2.0

Questions

How big is the Full route PCB?

It measures 21.3 × 33.4 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Full route use?

25 parts, built around the ATMEGA32U4. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Full route KiCad files?

From the JeremyJStarcher/Goldfish-clone-JLCPCB repository on GitHub, at the commit this page was made from: the board is 2-layer/goldfish/full-route.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Full route design in my own project?

Its repository states no licence, so its author keeps all rights: ask JeremyJStarcher before reusing the design.