

PCB DESIGN
Lavadora de piezas impresas con resina
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 49
- Nets
- 65
- Pads
- 202
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 29 Aug 2024
- Updated
- 6 Sep 2024
Overview
PCB DESIGN is an open-source printed circuit board by JABB09, from the JABB09/Wash-And-Cure repository on GitHub. It is a 2-layer board with 49 parts on 65 nets.
It is built around the ATMEGA328PB-AU, DRV8825PWP and LM2596S-5.0, with the SN74HC14PWR-TP among its other parts. Its parts include 20 capacitors, 13 resistors, 5 switches, 4 ICs and 2 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
4ATMEGA328PB-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 27 2KB 32KB 8 Bit AVR Built-in FLASH Power-on reset (POR)、Undervoltage detection (BOR/LVD/LVR/LVI)、Watchdog reset、External pin reset (NRST)、Built-in general-purpose timer、Programmable watchdog、Touch function TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)DRV8825PWP
HTSSOP-28-EP-40℃~+85℃ 2 2.5A 200mΩ 32 8.2V~45V Bipolar Driver STEP/DIR Yes HTSSOP-28-EP Stepper Motor Driver ROHSTexas InstrumentsStepper Motor DriverLM2596S-5.0
TO-263-5-40℃~+125℃@(TJ) 1 150kHz 3A 4.5V~40V 5V 5mA Buck Buck Built-in Fixed No TO-263-5 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersSN74HC14PWR-TP
TSSOP-14-40℃~+125℃ 1.5V、1.9V、2.2V、2.4V、3.8V 100mV、300mV、400mV、450mV、550mV、550mV 10uA 2V~6V 3.5ns@5V,15pF 6 74HC Schmitt trigger TSSOP-14 Inverters ROHSTECH PUBLICInverters
Parts
49| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | R | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R5, R6, R7, R8, R9, R10, R11, R12, R13 |
| 6 | 0.1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C7, C8, C10, C16, C20 |
| 5 | C | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9, C11, C17, C18, C19 |
| 5 | SW_Push | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | SW1, SW2, SW3, SW4, SW5 |
| 2 | 0.10 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 2 | 0.1μF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C13, C15 |
| 2 | 22pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C5, C6 |
| 2 | 470μF | Capacitor_SMD:CP_Elec_4x5.3 | C12, C14 |
| 2 | Screw_Terminal_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1, J2 |
| 1 | 0.47uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2 |
| 1 | 100uF | Capacitor_SMD:CP_Elec_4x5.3 | C4 |
| 1 | 10k | Potentiometer_SMD:Potentiometer_Bourns_3314J_Vertical | RV1 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3 |
| 1 | 16 Mhz | Crystal:Crystal_SMD_0603-2Pin_6.0x3.5mm | Y1 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 1 | 47μH | INDUCTOR_47uH:IND_SRR1240-470M | L1 |
| 1 | ATmega328PB-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U4 |
| 1 | DRV8825PWP | DRV8825:IC_TPS61196PWPRQ1 | U1 |
| 1 | D_Schottky_Small | Diode_SMD:D_SMA | D1 |
| 1 | LM2596S-5 | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U6 |
| 1 | R_Potentiometer | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | RV2 |
| 1 | SN74HC14PWR | SN74HC14PWR:SOP65P640X120-14N | U3 |
Similar boards
- 2 layers

- 2 layers

- 4 layers221.5 × 130.8 mm

MEP MAXI-85V-1-REV-2-Interface Board
JGilcreast/MetalHead
An opensource firmware and software drop-in replacement for the 85V Automatic Stirrup Bender by CRS Specialties Inc. ...short story behind the name...
407 parts - 4 layers90 × 70 mm

InclinationMeter
soldernerd/InclinationMeter
A battery-powered, Bluetooth-enabled precision electronic level instrument for machine tool geometry inspection and granite surface plate qualification.
118 parts - 2 layers100 × 100 mm

- 4 layers62 × 34 mm

Motor board v3
felixzero/escrocs
Repository for the ESCROCS team for the french robotics cup 2020!
75 parts7GPL-3.0 - 2 layers100 × 99.8 mm

- 2 layers125 × 125 mm

Diy robotics arm
mathias31415/diy_robotics
Gripper, PCBs and ROS2 software for Six-Axis Robot Arm WE-R2.4 from LoboCNC
34 parts39
Questions
What parts does the PCB DESIGN use?
49 parts, built around the ATMEGA328PB-AU, DRV8825PWP, LM2596S-5.0 and SN74HC14PWR-TP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the PCB DESIGN KiCad files?
From the JABB09/Wash-And-Cure repository on GitHub, at the commit this page was made from: the board is PCB_DESIGN/PCB_DESIGN.kicad_pcb and its schematic PCB_DESIGN/PCB_DESIGN.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the PCB DESIGN design in my own project?
Its repository states no licence, so its author keeps all rights: ask JABB09 before reusing the design.