
Relatively Universal ROM Programmer
AndersBNielsen/Relatively-Universal-ROM-Programmer
Hardware to program W27C512 EEPROM or any 24/28/32 pin ROM requiring from 5V to 27V programming voltage.

InSPIRE Project Team official repository
Dualaxis is an open-source printed circuit board by InSPIREUIUC, from the InSPIREUIUC/InSPIRE_PT repository on GitHub, published under the MIT licence. It is a 2-layer board of 125.5 × 91 mm with 15 parts on 32 nets, routed with 71 tracks and 4 vias.
It is built around the ARDUINO UNO R3 and PR4. Its parts include 10 connectors and 4 resistors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
The official repo for InSPIRE
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | Conn_01x01 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Horizontal | J1, J2, J3, J4, J5, J6 |
| 4 | 220 | Resistor_SMD:R_0805_2012Metric | R5, R6, R7, R8 |
| 1 | Arduino_UNO_R3 | Module:Arduino_UNO_R3_WithMountingHoles | A1 |
| 1 | PR_1 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | J7 |
| 1 | PR_2 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | J8 |
| 1 | PR_3 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | J9 |
| 1 | PR_4 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | J10 |

AndersBNielsen/Relatively-Universal-ROM-Programmer
Hardware to program W27C512 EEPROM or any 24/28/32 pin ROM requiring from 5V to 27V programming voltage.

AlanFord/self-balancing-stick
Dual Axis Reaction Wheel Inverted Pendulum

Edging-Machines/Edging-Machines
This repository is intended to contain as much information as possible about building, designing, prototyping, and using automated edging machines.

PedroCNeves/AC_ChargingStation
A learning project to create an EV AC Charging station based on an Arduino Uno

jonsag/arduTester
An arduino component tester based on https://create.arduino.cc/projecthub/plouc68000/ardutester-v1-13-the-arduino-uno-transistor-tester-dbafb4


ICRS/101
The all-new open source Robotics 101 course from ICRS. It's specifically designed to be run in hackspaces, after school clubs and university societies.

It measures 125.5 × 91 mm and has 2 copper layers, 1.6 mm thick.
15 parts, built around the ARDUINO UNO R3 and PR4. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the InSPIREUIUC/InSPIRE_PT repository on GitHub, at the commit this page was made from: the board is dual_axis_pv/kicad_version_control/ahmed/dualaxis.kicad_pcb and its schematic dual_axis_pv/kicad_version_control/adi/ADI_InSPIRE_Initial_Schematic.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).