

Eval board
A solution for room reservation display
- Size
- 117 × 60 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 38
- Nets
- 37
- Pads
- 157
- Tracks, vias
- 423, 30
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 3 Feb 2021
- Updated
- 29 May 2024
Overview
Eval board is an open-source printed circuit board by INSA-GEI, from the INSA-GEI/afficheurs repository on GitHub. It is a 2-layer board of 117 × 60 mm with 38 parts on 37 nets, routed with 423 tracks and 30 vias.
It is built around the MAX17220ELT+T, MBR0530 and SI1308EDL. Its parts include 15 capacitors, 7 connectors, 4 resistors, 3 ICs and 3 diodes. It belongs with the lEDs and displays boards and the STM32 boards of this library.
Main components
3MAX17220ELT+T
UDFN-6(2x2)-40℃~+85℃ 1 1.8V~5V 2MHz 300nA 400mV~5.5V Adjustable Boost Boost Built-in Overcurrent Protection、Light load efficient mode、Load disconnect Yes UDFN-6(2x2) DC-DC Converters ROHSMaxim Integrated (Analog Devices)DC-DC ConvertersMBR0530
SOD-1231 Independent 30V 5.5A 500mA 550mV@500mA 80uA@30V SOD-123 Schottky Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Schottky DiodesSI1308EDL
SC-70-3-55℃~+150℃ 1 N-channel 1.4nC@10V 1.5A 1.5V 105pF 11pF 132mΩ@10V 23pF 30V 400mW N-Channel SOT-323 MOSFETs ROHSVishay IntertechnologyMOSFETs
README
hardware/pcb/Pi uHat Xbee3/README.mdRaspberry Pi Zero pHat uHat template
This a KiCad 5.0.0 template for a Raspberry Pi Zero or Raspberry Pi Zero W sized uHat. It is based on the Raspberry Pi B+ Hat template from Xess Corp. They did all the hard work here.
Raspberry Pi Foundation has finally named these Raspberry Pi Zero sized hats which some called pHats. The new name is Micro-Hat or uHat. They also released a mechanical specification for them here. Luckily these specifications exactly match the template. Note the new POE keepout area is not in this template. You will have to keep track of it yourself.
Both a thru-hole and a surface mount connector are provided, along with a different PCB edge for each. Just keep the PCB edge and connector type that you're using for your design and delete the others. The surface mount header is on the bottom of the board. Keep in mind if you flip it to the top side even/odd pins will be swapped unless you also switch the foot print to "Samtec_HLE-120-02-xxx-DV-BE-A_2x20_RPi_Top".
Using the Template
Follow the instructions listed in the original Raspberry Pi B+ Hat template from XESS Corp.
Parts
38| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 1µF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C2, C3, C4, C5, C6, C7, C8, C9, C10, C15 |
| 6 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1, J3, J4, J5, J6, J7 |
| 3 | MBR0530 | Diode_SMD:D_TUMD2 | D1, D2, D3 |
| 2 | 10µF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C13, C14 |
| 2 | 4.7µF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C11, C12 |
| 1 | 100R | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R5 |
| 1 | 10K | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R2 |
| 1 | 1M | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R4 |
| 1 | 2,2µH | Inductor_SMD:L_Wuerth_MAPI-4030 | L2 |
| 1 | 3R | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1 |
| 1 | 68µH | Inductor_SMD:L_1210_3225Metric_Pad1.42x2.65mm_HandSolder | L1 |
| 1 | Conn_01x24 | Connector_FFC-FPC:Hirose_FH12-24S-0.5SH_1x24-1MP_P0.50mm_Horizontal | J2 |
| 1 | MAX17220ELT | Insa:uDFN-6-1EP_2x2mm_P0.65mm_EP1x1.6mm | U3 |
| 1 | R_POT_TRIM | Potentiometer_SMD:Potentiometer_Bourns_3269P_Horizontal | RV1 |
| 1 | STM32L031 | Insa:STM32-Nucleo-32 | U1 |
| 1 | SW_SPDT | Button_Switch_THT:SW_Slide_1P2T_CK_OS102011MS2Q | SW1 |
| 1 | SW_SPST | Button_Switch_THT:SW_TH_Tactile_Omron_B3F-10xx | SW2 |
| 1 | Si1308EDL | Package_TO_SOT_SMD:SOT-323_SC-70_Handsoldering | Q1 |
| 1 | XBee3 | Insa:Xbee3 | U2 |
More from INSA-GEI/afficheurs
1- 2 layers65 × 30.5 mm

Similar boards
- 2 layers25 × 100 mm

Nrf51x22 qfax dcdc
AmeliaEScott/BLESoilMoistureSensors
PCB design files and Rust firmware for solar-powered BLE soil moisture sensors
116 parts - 4 layers45 × 32 mm

Templog mainboard
Michael-Manning/E-Paper-Climate-Logger
Firmware, PCB, and enclosure for the Weathergotchi E-Paper climate logger.
68 parts457MIT - 2 layers83.2 × 40 mm

- 2 layers45 × 45 mm

Aeroq Hardware v3
EnriqueNeyra/Aeroq
An Indoor Air Quality Monitor Powered by ESP32, SCD40, and SEN54
56 parts130 - 2 layers35 × 45 mm

Aether
EnriqueNeyra/aether
All-in-one home air quality monitor measuring Temp, Humidity, CO2, VOCs, Particulate Matter, and NOx. Powered by ESP32-C3 running esphome, and built with Home Assistant integration
57 parts129 - 2 layers69.4 × 113 mm

- 4 layers36.5 × 69 mm

Storm tracker
solderable/storm-tracker-hardware
Open-source-ready Storm Tracker hardware design, documentation, BOM, and manufacturing package
102 parts58 - 4 layers70.2 × 71 mm

C3-27-epaper touch
martinberlin/bistable-smart-switch
An epaper switch project with 2 PCBs, controller+touch, and 220AC to 3DC with Relay (Latch or solid-state)
64 parts32Apache-2.0
Questions
How big is the Eval board PCB?
It measures 117 × 60 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Eval board use?
38 parts, built around the MAX17220ELT+T, MBR0530 and SI1308EDL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Eval board KiCad files?
From the INSA-GEI/afficheurs repository on GitHub, at the commit this page was made from: the board is hardware/pcb/eval-board/eval-board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Eval board design in my own project?
Its repository states no licence, so its author keeps all rights: ask INSA-GEI before reusing the design.