Skip to the content
2 layers25 × 50 mmEmber flight recorder, the printed circuit board in 3D

Ember flight recorder

HexDump0/Ember

A cheap, diy model rocket with a flight recorder and everything else you would need to fy it See the guide » Video (Soon) Models Gerber Firmware

Size
25 × 50 mm
Copper layers
2
Thickness
1.6 mm
Parts
19
Nets
32
Pads
73
Tracks, vias
123, 14
Pours
4
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
27 Apr 2026
Updated
22 May 2026

Overview

Ember flight recorder is an open-source printed circuit board by HexDump0, from the HexDump0/Ember repository on GitHub. It is a 2-layer board of 25 × 50 mm with 19 parts on 32 nets, routed with 123 tracks and 14 vias.

It is built around the DW01A, AO3401A and FS8205A. Its parts include 6 capacitors, 5 ICs, 3 resistors, 2 transistors and 1 diode. It belongs with the ESP32 and RISC-V boards of this library.

Main components

3

README

README.md

[blocked]

Contributors Forks Stargazers Issues


Ember

A cheap, diy model rocket with a flight recorder and everything else you would need to fy it
See the guide »

Video (Soon) [blocked] · Models · Gerber · Firmware

About The Project

Render

Ember is a diy, cheap and open source model rocket along with everything you would need to launch it + detailed guides on actually building it

(back to top)

Images

OpenRocket

Flight Recorder
Flight Recorder
Flight Recorder 3D
Flight Recorder 3D
Dashboard
Dashboard
Launch Controller
Launch Controller
Launch Controller 3D
Launch Controller 3D

Guide

3D Printing

A few of the important parts of the rocket are 3d printed, you could get away with using PLA for them but ABS is better if you have it.

Recommended print settings:

  • Layer heigh -> 0.2mm
  • Wall lines -> 5
  • Infill -> Gyroid 40%
  • Top & Bottom layers -> 4

Nose cone

Add normal supports for the lip in the shoulder. It should come off easily

Nose

Fins x4

Print it with the fin tab facing the bed and with the Seam corner preference set to Hide Seam

Fins

Launch lugs x2

Engine block

Centering rings x2

Launch Controller Body/Panel

Launch Pad Leg/Body

You can just print these with the recommenced settings

PCB/Electronics

The gerber files for both the launch controller and flight recorder are available here

Make sure you would a bit of 22 AWG wires at hand for the panel lights and switches

The Battery is meant to be charged on the bench and then soldered on to the flight recorder

(More detailed guide will come once I get my PCBs)

Flashing the firmware

You need esptool. Install it using

sh
pip install --user esptool

Plug the Super Mini into USB. It should show up as /dev/ttyACM0 on Linux, /dev/tty.usbmodem* on macOS, and COMx on Windows

Flash the firmware using

sh
esptool --chip esp32c3 --port /dev/ttyACM0 --baud 460800 \
        write-flash 0x0 ember.bin

Once done you should see some logs in serial

sh
# pick one
idf.py -p /dev/ttyACM0 monitor
miniterm /dev/ttyACM0 115200
screen /dev/ttyACM0 115200
text
I (xxx) ember: ember boot
I (xxx) sensors: MPU6050 ready @0x68
I (xxx) sensors: BMP280 ready @0x76 ...
I (xxx) httpd: http server up on :80
I (xxx) wifi_ap: softap up: ssid=ember-XXXXXX ch=1

Connect to the open Wi-Fi ember-XXXXXX and visit http://192.168.4.1 for the dashboard.

License

Distributed under the Creative Commons Attribution-NonCommercial 4.0. See LICENSE.md for more information.

(back to top)

Contact

HexDump0 - @HexDump0 - root@hexdump0.pw

Project Link: https://github.com/HexDump0/Ember

(back to top)

Acknowledgments

  • SnapEDA for ESP32-C3 SMD Footprint and Symbol
  • UltraLibrarian for FS8205A Footprint and Symbol
  • RabchikEngineer for KiCad ESP32-C3-SuperMini symbols
  • Ulf Hille for ESP32C3 SuperMini 3D Model
  • Usini for Usini Sensors Kicad Schematics and footprints (and associated GrabCAD authors)

(back to top)

Parts

19
QtyValueFootprintReferences
21uFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC3, C4
10.1uFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC1
1100Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR7
1100nFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC6
1100uFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC2
110uFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC5
12.2kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR6
1330Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR5
1AO3401APackage_TO_SOT_SMD:SOT-23Q4
1DW01APackage_TO_SOT_SMD:SOT-23-6U2
1ESP32-C3_SUPERMINI_SMDsmd:MODULE_ESP32-C3_SUPERMINIU6
1FS8205AFS8205A:SOT-23-6L_TCP-MQ3
1LEDLED_SMD:LED_1210_3225Metric_Pad1.42x2.65mm_HandSolderD5
1LiPo batteryConnector_Wire:SolderWire-0.75sqmm_1x02_P7mm_D1.25mm_OD3.5mmBT1
1MCP1700x-330xxTTPackage_TO_SOT_SMD:SOT-23U3
1SW_SPDTButton_Switch_THT:SW_Slide-03_Wuerth-WS-SLTV_10x2.5x6.4_P2.54mmSW1
1module_bme280usini_sensors:module_bme280U5
1module_mpu6050usini_sensors:module_mpu6050U4

More from HexDump0/Ember

1
  • 2 layers75 × 52.5 mmEmber launch controller, the printed circuit board in 3D

    Ember launch controller

    HexDump0/Ember

    A cheap, diy model rocket with a flight recorder and everything else you would need to fy it See the guide » Video (Soon) Models Gerber Firmware

    19 parts

Similar boards

  • 2 layers60 × 111.3 mmSilkscreen pcb, the printed circuit board in 3D

    Silkscreen pcb

    iandchasse/silkscreen-pcb

    Silkscreen: open-hardware ESP32-S3 e-paper reader mainboard (KiCad 9). Formerly the de-link hub.

    189 parts589CERN-OHL-S-2.0
  • 2 layers35.1 × 28.9 mmBms buck boost, the printed circuit board in 3D

    Bms buck boost

    tor1kk/bms-buck-boost

    Battery Management System (BMS) with Buck-Boost Converter

    38 parts10GPL-3.0
  • 2 layers35 × 100 mmWalkieTalkie, the printed circuit board in 3D

    WalkieTalkie

    GuzziFlipFlops/ESP32-Walkie-Talkie

    An open source ESPNOW based walkie talkie with a 600 meter tested distance, with an OLED and multiple buttons to interact with

    66 parts7MIT
  • 2 layers78 × 103 mmEmbedded.old, the printed circuit board in 3D

    Embedded.old

    borisg912/3DNA

    This project creates a flat cylindrical DNA model with: - Magnetic DNA bases with color-coded NeoPixel LEDs and unique resistor values for identification - Interactive base pairing game that validates correct DNA base…

    121 parts2GPL-3.0
  • 2 layers96 × 50 mmPager, the printed circuit board in 3D

    Pager

    justinlindh/bramble

    Privacy-first LoRa mesh networking for ESP32-S3, built with ESP-IDF

    97 parts2MIT
  • 4 layers90 × 95 mmWiegand bridge, the printed circuit board in 3D

    Wiegand bridge

    EdgeCoil/wiegand-bridge

    ESP32-S3 Wiegand reader bridge for Home Assistant: 4-layer board, BOM and ESPHome firmware.

    197 parts1
  • 2 layers45 × 100 mmWalkiepcb, the printed circuit board in 3D

    Walkiepcb

    houseofthe051010/ESP32-Walkie-Talkie-V2

    This ESP32 Walkie Talkie is redesigned with a SX1262 radio, a PCB, and a full case redesign.

    93 parts1
  • 2 layers150 × 40 mmBicopter, the printed circuit board in 3D

    Bicopter

    InputBlackBoxOutput/Bicopter

    Design files for a PCB Bicopter

    79 parts1MIT

Questions

How big is the Ember flight recorder PCB?

It measures 25 × 50 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Ember flight recorder use?

19 parts, built around the DW01A, AO3401A and FS8205A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Ember flight recorder KiCad files?

From the HexDump0/Ember repository on GitHub, at the commit this page was made from: the board is kicad/ember_flight_recorder/ember_flight_recorder.kicad_pcb and its schematic kicad/ember_flight_recorder/ember_flight_recorder.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Ember flight recorder design in my own project?

Its repository states no licence, so its author keeps all rights: ask HexDump0 before reusing the design.