
Onizuka esp
HarkonenBade/onizuka
Psyduck (used in image on the ESP8266 board, due to the pun on ESP->ESP->Psychic) is Trademark & © of Nintendo 1996-2015

Psyduck (used in image on the ESP8266 board, due to the pun on ESP->ESP->Psychic) is Trademark & © of Nintendo 1996-2015
Onizuka is an open-source printed circuit board by HarkonenBade, from the HarkonenBade/onizuka repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board of 22.8 × 16 mm with 30 parts on 28 nets, routed with 280 tracks and 26 vias.
It is built around the FT232RQ and MIC5353-3.3YMT-TR. Its parts include 9 capacitors, 9 resistors, 5 diodes, 3 ICs and 2 connectors.
An FTDI based programming master board. With various daughter boards for programming specific modules.
Onizuka is licensed under Creative Commons Attribution-ShareAlike 4.0 International (CC BY-SA 4.0).
Psyduck (used in image on the ESP8266 board, due to the pun on ESP->ESP->Psychic) is Trademark & © of Nintendo 1996-2015
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 1k | Resistors_SMD:R_0402 | R1, R2, R3, R4, R7, R8 |
| 4 | 100n | Capacitors_SMD:C_0402 | C1, C4, C5, C6 |
| 3 | 1u | Capacitors_SMD:C_0402 | C7, C8, C9 |
| 1 | 10K | Resistors_SMD:R_0402 | R9 |
| 1 | 10n | Capacitors_SMD:C_0402 | C2 |
| 1 | 3v3 | LEDs:LED_0603 | D4 |
| 1 | 430K | Resistors_SMD:R_0402 | R6 |
| 1 | 4u7 | Capacitors_SMD:C_0402 | C3 |
| 1 | 51K | Resistors_SMD:R_0402 | R5 |
| 1 | 5v | LEDs:LED_0603 | D5 |
| 1 | ADCMP371 | TO_SOT_Packages_SMD:SC-70-5 | IC2 |
| 1 | FT232RQ | ftdi:FTDI-FT232RQ-QFN-32 | IC1 |
| 1 | FTDI | Socket_Strips:Socket_Strip_Angled_2x06 | P2 |
| 1 | MIC5353-3.3YMT | Housings_MLF:Thin_MLF_6_1.6mm_0.5mm_pitch | U1 |
| 1 | PWR | LEDs:LED_0603 | D3 |
| 1 | Q_PMOS_GSD | TO_SOT_Packages_SMD:SOT-23 | Q1 |
| 1 | RX | LEDs:LED_0603 | D2 |
| 1 | SPDT | Wurth:450301014042 | SW1 |
| 1 | TX | LEDs:LED_0603 | D1 |
| 1 | USB_OTG | Connect:USB_Micro-B | P1 |

HarkonenBade/onizuka
Psyduck (used in image on the ESP8266 board, due to the pun on ESP->ESP->Psychic) is Trademark & © of Nintendo 1996-2015


Starman3787/btc-split-flap
Project to display the value of bitcoin on a split-flap display.

BenjaminJAnderson/CUBE
CUBE is a miniature, six-faced OLED display cube built from a stack of custom interconnected PCBs. The current design combines an ESP32-S2 motherboard, five further display boards, a magnet-held 3D-printed frame and…

ChladpavPy/Aero-Zero
I started this project, because I wanted to build fully autonomous ai drone. When I looked at the flight controllers available on the market, they were full of hardware that I just do not need or just that I could not…

Jeija/esp8266-smartwatch
ESP8266 DIY WiFi Smartwatch with MPU-9250, RTC, OLED, FT232, ...

ThomasVDD/SmartSupply
SmartSupply is a digital battery powered lab powersupply. It is Arduino compatible and can be controlled via PC over USB.

ladecadence/GBShooper
Open source hardware GameBoy™ FlashCart Reader/Programmer

mangobanaani/cirradio
Tactical UHF FHSS mesh radio: Zynq-7045 + AD9361, SystemVerilog RTL, C++20 comms stack, AES-256 PKCS#11 crypto
It measures 22.8 × 16 mm and has 2 copper layers, 1.6 mm thick.
30 parts, built around the FT232RQ and MIC5353-3.3YMT-TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the HarkonenBade/onizuka repository on GitHub, at the commit this page was made from: the board is master-board/onizuka.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).