

DEV BOARD
This project uses: - KiCad - Blender for 3D renders - Based on the Hack Club dev board tutorial
- Size
- 51 × 21 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 55
- Nets
- 66
- Pads
- 243
- Tracks, vias
- 840, 75
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 18 Jun 2026
- Updated
- 6 Aug 2026
Overview
DEV BOARD is an open-source printed circuit board by Gusus169, from the Gusus169/FORGE-V1.0 repository on GitHub, published under the MIT licence. It is a 2-layer board of 51 × 21 mm with 55 parts on 66 nets, routed with 840 tracks and 75 vias.
It is built around the RP2040, W25Q128JVSIQ and DW01A, with the MCP73831T-2ATI/OT-HXY, BAT54C and S2B-PH-SM4-TB among its other parts. Its parts include 23 capacitors, 11 resistors, 6 ICs, 5 connectors and 3 diodes. It belongs with the microcontroller boards boards and the RP2040 boards of this library.
Main components
7RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHDW01A
SOT-23-6L-40℃~+85℃ 1 2.5V 300mV~10V 3uA 4.3V Protection IC Support SOT-23-6L Battery Management ROHSPUOLOPBattery ManagementMCP73831T-2ATI/OT-HXY
SOT-23-5LBattery ManagementHXY MOSFETBAT54C
SOT-231 Pair Common Cathode 200mA 2uA@25V 30V 600mA 800mV@100mA SOT-23 Schottky Diodes ROHSNexperiaSchottky DiodesS2B-PH-SM4-TB
2A 100V, Pitch 2.0mm, 2 Positions Disconnectable Crimp Style, SMD Male Header, Side EntryJSTUncategorisedWS2812B-2020
SMD,2.2x2mm0.6mA 0.84mm 120us 160mcd 200mcd 2kHz 2mm 2mm 300ns 470.4nm 515.6nm 520mcd 5V 622.5nm 800Kbit/s Built-in power-on reset circuit、Built-in power-on reset circuit、Integrated intelligent reverse connection protection function Top-mount SMD,2.2x2mm RGB LEDs(Built-in IC) ROHSWorldsemiRGB LEDs(Built-In IC)
README
README.mdForge V1.0
A Raspberry Pi Pico-sized RP2040 development board with battery support and an RGB indicator
Key Features • PCB • Credits • License


Key Features
- RP2040 microcontroller, dual-core ARM Cortex-M0+
- Raspberry Pi Pico form factor for compatibility
- Battery charging with MCP73831 IC and DW01A+FS8205A protection, JST-PH connector for 1S LiPo
- MCP1700 LDO regulator for efficient 3.3V power
- WS2812B RGB LED for status indication
- USB-C connectivity
- Dedicated Reset and BOOTSEL buttons
- 16MB SPI flash (W25Q128JVS)
- Custom silkscreen artwork
PCB
Designed in KiCad.
Schematic

PCB
Front Routing:

Back Routing:

Front Assembly:
Back Assembly:
JLCPCB Order

Credits
This project uses:
- KiCad
- Blender for 3D renders
- Based on the Hack Club dev board tutorial
License
MIT
Parts
55| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C2, C3, C5, C6, C7, C8, C9, C10, C11, C13, C17, C19, C20, C21, C22, C23 |
| 4 | LOGO | LOGO | G***, G***, G***, G*** |
| 3 | 1K | Resistor_SMD:R_0402_1005Metric | R4, R5, R7 |
| 3 | 1uF | Capacitor_SMD:C_0402_1005Metric | C1, C4, C14 |
| 2 | 10K | Resistor_SMD:R_0402_1005Metric | R6, R11 |
| 2 | 10uF | Capacitor_SMD:C_0603_1608Metric | C12, C18 |
| 2 | 27ohm | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | 27pF | Capacitor_SMD:C_0402_1005Metric | C15, C16 |
| 2 | 5.1K | Resistor_SMD:R_0402_1005Metric | R9, R10 |
| 2 | Conn_01x20 | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | J2, J3 |
| 2 | SW_Push | Button_Switch_SMD:SW_SPST_B3U-1000P | BOOSTEL, SW2 |
| 1 | 12 MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 2K | Resistor_SMD:R_0402_1005Metric | R8 |
| 1 | 330ohm | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | BAT54C | Package_TO_SOT_SMD:SOT-23 | D1 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | DW01A | Package_TO_SOT_SMD:SOT-23-6 | U5 |
| 1 | LED red | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | MCP1700x-120xxMB | Package_TO_SOT_SMD:SOT-23 | U2 |
| 1 | MCP73831T-2ATI_OT | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | S2B-PH-SM4-TB | Connector_JST:JST_PH_B2B-PH-SM4-TB_1x02-1MP_P2.00mm_Vertical | J5 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J4 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | WS2812B-2020 | LED_SMD:LED_WS2812B-2020_PLCC4_2.0x2.0mm | D2 |
| 1 | ~ | Package_TO_SOT_SMD:SOT-23-6 | U6 |
Similar boards
- 4 layers69.8 × 35.2 mm

- 4 layers65 × 100 mm

- 4 layers65 × 100 mm

Audcalc
sinitsinmike/Audcalc2
I'm happy with this, but its not 100% feature complete on the firmware side. Its really neat though, and I think you'll like it.
218 partsMIT - 4 layers56 × 38 mm

- 4 layers50 × 70 mm

Stm32-portable data logger
copperheadhq/copperhead-stm32-data-logger
Portable STM32L433 data logger, 50 × 70 mm, four layers, microSD, USB-C LiPo charging. Designed with copperhead. Never built: do not order expecting it to work.
90 parts3 - 4 layers50 × 50 mm

FC v02
pacman314159/OISP-Drone-Research
mermaid stateDiagram-v2 [] --> POWERON POWERON --> BOOTINIT: Power Applied / Reset BOOTINIT --> SENSORCALIBRATION: Hardware Self-Test Pass BOOTINIT --> SYSTEMERROR: Self-Test Fail SENSORCALIBRATION --> DISARMED…
87 parts - 2 layers50.8 × 44.5 mm

- 4 layers61.8 × 27.5 mm

Audio Processing HW V1.0
aitesam961/OpenADSP
An Embedded Digital Signal Processing Device for Audio signals.
83 parts4GPL-3.0
Questions
How big is the DEV BOARD PCB?
It measures 51 × 21 mm and has 2 copper layers, 1.6 mm thick.
What parts does the DEV BOARD use?
55 parts, built around the RP2040, W25Q128JVSIQ, DW01A and MCP73831T-2ATI/OT-HXY. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the DEV BOARD KiCad files?
From the Gusus169/FORGE-V1.0 repository on GitHub, at the commit this page was made from: the board is KiCad/DEV BOARD.kicad_pcb and its schematic KiCad/CRYSTAL.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the DEV BOARD design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).