Skip to the content
4 layers26 × 30 mmLte m dongle fw, the printed circuit board in 3D

An LTE-M / NB-IoT cellular modem built into the Framework Laptop Expansion Card form factor, with a native USB-C plug.

Size
26 × 30 mm
Copper layers
4
Thickness
1.6 mm
Parts
32
Nets
70
Pads
184
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 10.0 (file 20260206)
Created
23 Jun 2026
Updated
23 Jun 2026

Overview

Lte m dongle fw is an open-source printed circuit board by GManSudy, from the GManSudy/framework-expansion-lte repository on GitHub. It is a 4-layer board of 26 × 30 mm with 32 parts on 70 nets.

It is built around the SIM7080G, TPS62A01DRL and TPD3F303DPVR, with the PRTR5V0U2X and SIM8060-6-0-14-00-A among its other parts. Its parts include 8 capacitors, 8 resistors, 3 ICs, 3 connectors and 1 diode.

Main components

5

README

README.md

Framework Expansion Card — LTE-M Modem (USB-C)

An LTE-M / NB-IoT cellular modem built into the Framework Laptop Expansion Card form factor, with a native USB-C plug.

The design is a clean re-implementation of Aurélien Jarno's LTE-M dongle, re-housed in the 26 × 30 mm Framework card outline and converted from USB-A to USB-C.

Features

  • SIMCom SIM7080G Cat-M1 / NB-IoT modem with integrated GNSS
  • USB-C plug (USB 2.0) directly into a Framework expansion bay
  • CC1 / CC2 pulldowns (5.1 kΩ) so the host enumerates the card and supplies VBUS
  • On-board nanoSIM holder (back side)
  • TPS62A01 buck regulator for the modem rails
  • TPD3F303 USB ESD / EMI protection
  • SMA edge connector for an external LTE antenna
  • 4-layer board, 26 × 30 mm, 2 × M2 mounting holes (Framework standard)

USB-C wiring (J1)

SignalPinsNotes
VBUSA4, A9, B4, B95 V from host
GNDA1, A12, B1, B12Shield → ferrite FB2 → GND
D+ / D-A6 / A7USB 2.0 data
CC1 / CC2A5 / B5R7 / R8 = 5.1 kΩ to GND

Layout

  • Front: USB-C plug (top), SIM7080G U1 (centre), SMA J2 (bottom edge), power/USB front-end and status LEDs in the side columns.
  • Back: nanoSIM holder J3 (centre), bias resistors, decoupling and jumpers.

Status: the PCB is fully placed and net-correct but unrouted — copper traces and pours are left for you. kicad-cli pcb drc --schematic-parity reports 0 schematic-parity issues (the PCB matches the schematic exactly).

Bill of Materials

See BOM.csv. Summary:

RefsValueFootprintQty
C110nC_06031
C2, C7, C8100nC_06033
C3, C5, C622uC_08053
C4120pC_06031
D1PRTR5V0U2XSOT-1431
FB1, FB2120R / 0.5AL_06032
J1USB-C plugMolex 1054441
J2SMA edgeCON-SMA-EDGE-S1
J3nanoSIMGCT SIM80601
JP1PWRKEYSolderJumper-31
JP2BOOTCFGSolderJumper-21
L11uL_10081
LD1, LD2LEDLED_06032
R1536kR_06031
R2100kR_06031
R3, R410kR_06032
R5, R6220R_06032
R7, R85k1R_06032
U1SIM7080GSIMCom LCC1
U2TPS62A01SOT-5631
U3TPD3F303DPVRR-PUSON-81

Plus H1, H2: 2 × M2 mounting holes (no part).

Opening the project

Open lte-m-dongle-fw.kicad_pro in KiCad 9 or 10. The custom symbols and footprints (SIM7080G, TPS62A01, TPD3F303, nanoSIM, SMA, USB-C plug) ship with the project and are referenced through ${KIPRJMOD} in sym-lib-table / fp-lib-table.

Credits

Parts

32
QtyValueFootprintReferences
3100nC_0603_1608MetricC2, C7, C8
322uC_0805_2012MetricC3, C5, C6
210kR_0603_1608MetricR3, R4
2120R/0.5AL_0603_1608MetricFB1, FB2
2220R_0603_1608MetricR5, R6
25k1R_0603_1608MetricR7, R8
2LEDLED_0603_1608MetricLD1, LD2
2MountingHoleMountingHole_2mmH1, H2
1100kR_0603_1608MetricR2
110nC_0603_1608MetricC1
1120pC_0603_1608MetricC4
11uL_1008_2520MetricL1
1536kR_0603_1608MetricR1
1BOOTCFGSolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP2
1CON-SMA-EDGE-SSMA_RF-Solutions_CON-SMA-EDGE-S_EdgeMountJ2
1PRTR5V0U2XSOT-143D1
1PWRKEYSolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mmJP1
1SIM7080GSIM7080GU1
1SIM8060-6-0-14-00-AnanoSIM_GCT_SIM8060-6-0-14-00-AJ3
1TPD3F303DPVRTexas_R-PUSON-N8_EP0.4x1.7mmU3
1TPS62A01SOT-563U2
1USB_C_Plug_USB2.0USB_C_Plug_Molex_105444J1

Similar boards

  • 4 layers71.5 × 54.4 mmAttempt2, the printed circuit board in 3D

    Attempt2

    m3llo0n/stat-pcb

    schematic + pcb for the new tech

    60 parts1
  • 4 layers118 × 93 mmNRF9161-v2-panel, the printed circuit board in 3D

    NRF9161-v2-panel

    anand2532/nRF9161-DEV-BOARD

    A small 50 × 37.5 mm LTE-M / NB-IoT + GNSS modem board built around the Nordic nRF9161. Any host MCU controls it with AT commands over one 10-pin UART header.

    474 parts
  • 4 layers71.4 × 56.4 mmFishIoT, the printed circuit board in 3D

    FishIoT

    tsotnek/IoF-Design-Files

    134 parts
  • 4 layers40 × 80 mmSIM7600-breakout, the printed circuit board in 3D

    SIM7600-breakout

    lamemakes/SIM7600-breakout

    A breakout board for the SIM7600 LTE module

    69 parts6
  • 4 layers124.7 × 64.3 mmRP2040 SOS band, the printed circuit board in 3D

    RP2040 SOS band

    abhinav937/RP2040_SOS_band

    PCB design files for RP2040 based SmartWatch. It features an accelerometer, a GPS module and a cellular module.

    107 parts3
  • 2 layers52 × 29 mmCellular featherwing pcb, the printed circuit board in 3D

    Cellular featherwing pcb

    keenanjohnson/cellular-featherwing-pcb

    The PCB Design for a Cellular Adafruit Featherwing based on the Quectel BG96 LTE Cat M1 & Cat NB1.

    64 parts1
  • 4 layers32.5 × 67 mmHw thingcell, the printed circuit board in 3D

    Hw thingcell

    GuilleGonzzalez/hw-thingcell

    Firmware used in this device is fw-thingcell, a custom made firmware implemented using Arduino Home Assistant Arduino library (docs).

    101 parts

Questions

How big is the Lte m dongle fw PCB?

It measures 26 × 30 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Lte m dongle fw use?

32 parts, built around the SIM7080G, TPS62A01DRL, TPD3F303DPVR and PRTR5V0U2X. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Lte m dongle fw KiCad files?

From the GManSudy/framework-expansion-lte repository on GitHub, at the commit this page was made from: the board is lte-m-dongle-fw.kicad_pcb and its schematic lte-m-dongle-fw.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Lte m dongle fw design in my own project?

Its repository states no licence, so its author keeps all rights: ask GManSudy before reusing the design.