

Hw thingcell
Firmware used in this device is fw-thingcell, a custom made firmware implemented using Arduino Home Assistant Arduino library (docs).
- Size
- 32.5 × 67 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 101
- Nets
- 130
- Pads
- 367
- Tracks, vias
- 444, 224
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 6 Sep 2023
- Updated
- 23 Jan 2024
Overview
Hw thingcell is an open-source printed circuit board by GuilleGonzzalez, from the GuilleGonzzalez/hw-thingcell repository on GitHub. It is a 4-layer board of 32.5 × 67 mm with 101 parts on 130 nets, routed with 444 tracks and 224 vias.
It is built around the CH340C, ESP32-S2-SOLO-N8 and SIM868, with the 1N4448W-7-FS, SIM8060-6-0-14-00-A and USB4510-03-1-A among its other parts. Its parts include 31 resistors, 22 capacitors, 8 diodes, 8 connectors and 5 ICs. It belongs with the ESP32 boards of this library.
Main components
6CH340C
SOP-16-20℃~+70℃ 2Mbps 3.3V、5V 50uA 7mA Transceiver USB 2.0 SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersESP32-S2-SOLO-N8
-- WiFi Modules ROHSEspressif SystemsWiFi ModulesSIM868
SMD,17.6x15.7mm-40℃~+85℃ 3.4V~4.4V 650uA 850MHz、900MHz、1800MHz、1900MHz GPRS、GSM I2C、USB、UART、SIM card、SD card Noise suppression function、USSD function、Assisted GNSS function SMD,17.6x15.7mm 2G/3G/4G/5G Modules ROHSSIMCom Wireless Solutions2G/3G/4G/5G Modules1N4448W-7-FS
SOD-123SOD-123 Switching Diodes ROHSFUXINSEMISwitching DiodesSIM8060-6-0-14-00-A
SMD-20℃~+85℃ 1.42mm 125V Connector and Ejector Hinged Lid Nano-SIM Card SMD SIM Card Connectors ROHSGlobal Connector Technology (GCT)SIM Card ConnectorsUSB4510-03-1-A
SMDUSB ConnectorsGlobal Connector Technology (GCT)
README
README.mdThingCell

Description
'ThhingCell' is a device designed to control a other devices with a relay with MQTT over 4G .
Firmware used in this device is fw-thingcell, a custom made firmware implemented using Arduino Home Assistant Arduino library (docs).
Power supply (WIP)
Microprocessor (WIP)
Espressif ESP8266 module.
Environmental sensing (WIP)
The board has enviromental sensors to measure temperature, humidity and atmospheric pressure:
Temperature and humidity sensor
- Sensirion SHT40.
Pressure sensor
- Bosch BMP581.
LEDs and buttons (WIP)
Pin assignment (WIP)
| PIN | Func |
|---|---|
| GPIOx | F1 |
Enclosure (WIP)
- Custom made in Fusion 360.
Changelog (WIP)
All notable changes to this project will be documented in this section.
The format is based on Keep a Changelog
unreleased - 2023-09-06
Unreleased
Parts
101| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 1k | Resistor_SMD:R_0402_1005Metric | R8, R12, R16, R17, R25, R26, R27, R28, R29, R30, R31 |
| 7 | 10k | Resistor_SMD:R_0402_1005Metric | R1, R3, R5, R7, R13, R14, R18 |
| 5 | 100n | Capacitor_SMD:C_0402_1005Metric | C7, C8, C9, C21, C22 |
| 5 | 22u | Capacitor_SMD:C_0805_2012Metric | C3, C10, C11, C12, C13 |
| 4 | D_TVS | Diode_SMD:D_0402_1005Metric | D5, D6, D7, D8 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_2.2mm_M2_ISO7380_Pad | H1, H2, H3, H4 |
| 3 | 10u | Capacitor_SMD:C_0805_2012Metric | C1, C2, C15 |
| 3 | 22p | Capacitor_SMD:C_0402_1005Metric | C18, C19, C20 |
| 3 | 5.6k | Resistor_SMD:R_0402_1005Metric | R22, R23, R24 |
| 3 | 51 | Resistor_SMD:R_0402_1005Metric | R19, R20, R21 |
| 3 | PMBT3904235 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3 |
| 2 | 12p | Capacitor_SMD:C_0402_1005Metric | C5, C6 |
| 2 | 3u3 | guille-lib:SRN5020TA3R3M | L1, L2 |
| 2 | 5k1 | Resistor_SMD:R_0402_1005Metric | R6, R10 |
| 2 | AP62301WU-7 | guille-lib:SOT95P280X100-6N | U1, U2 |
| 2 | Conn_01x02_Pin | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J1, J2 |
| 2 | Conn_01x08_Pin | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J3, J5 |
| 2 | LED | LED_SMD:LED_0402_1005Metric | D3, D4 |
| 2 | NC | Resistor_SMD:R_0402_1005Metric | R9, R11 |
| 1 | 10 | Resistor_SMD:R_0402_1005Metric | R15 |
| 1 | 100u_tant | guille-lib:CAPPM3528X210N | C14 |
| 1 | 10p | Capacitor_SMD:C_0402_1005Metric | C17 |
| 1 | 1N4448W-7-F | Diode_SMD:D_SOD-123 | D1 |
| 1 | 27n | Inductor_SMD:L_0402_1005Metric | L3 |
| 1 | 31k6 | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 32.768k | guille-lib:SC32S7PF20PPM | Y1 |
| 1 | 33p | Capacitor_SMD:C_0402_1005Metric | C16 |
| 1 | 3V3 | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | 40k | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 4V | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | 5V | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | BZT52C5V1-7-F | guille-lib:SOD3716X145N | D2 |
| 1 | CH340C | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U5 |
| 1 | ESP32-S2-SOLO | PCM_Espressif:ESP32-S2-SOLO | U3 |
| 1 | ESP_EN | TestPoint:TestPoint_Pad_D1.0mm | TP7 |
| 1 | ESP_IO0 | TestPoint:TestPoint_Pad_D1.0mm | TP12 |
| 1 | ESP_IO45 | TestPoint:TestPoint_Pad_D1.0mm | TP9 |
| 1 | ESP_IO46 | TestPoint:TestPoint_Pad_D1.0mm | TP8 |
| 1 | ESP_RX | TestPoint:TestPoint_Pad_D1.0mm | TP10 |
| 1 | ESP_TOUCH1 | TestPoint:TestPoint_Pad_D1.0mm | TP13 |
| 1 | ESP_TX | TestPoint:TestPoint_Pad_D1.0mm | TP11 |
| 1 | GND | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | GNSS_ANT | guille-lib:U.FL_CONNECTOR | J7 |
| 1 | GNSS_EN | TestPoint:TestPoint_Pad_D1.0mm | TP14 |
| 1 | GSM_ANT | guille-lib:U.FL_CONNECTOR | J6 |
| 1 | NC | Capacitor_SMD:C_0402_1005Metric | C4 |
| 1 | RF_SYNC | TestPoint:TestPoint_Pad_D1.0mm | TP16 |
| 1 | SIM8060-6-0-14-00-A | guille-lib:SIM8060601400A | J8 |
| 1 | SIM868 | guille-lib:SIM868 | U4 |
| 1 | USB4510-03-1-A | guille-lib:USB4510031A | J4 |
| 1 | VBUS | TestPoint:TestPoint_Pad_D1.0mm | TP5 |
| 1 | VDD_EXT | TestPoint:TestPoint_Pad_D1.0mm | TP15 |
| 1 | VIN | TestPoint:TestPoint_Pad_D1.0mm | TP6 |
Similar boards
- 2 layers46.4 × 38.1 mm

- 2 layers38.1 × 38.1 mm

SIM868
vul-os/sirboard
Open hardware: 107 KiCad PCB designs — SMD-to-THT breakout adapters, ATTiny/ATMega/ESP development boards, and a 39-part sensor line on a common JST-SH connector.
73 parts56Apache-2.0 - 2 layers33 × 85 mm

GL868 ESP32V3.1
RamRamAndroid/GeoTinker-CodeMatrix
The GeoTinker GL868_ESP32 is a production-ready, open-source development board that combines an ESP32-S3 and SIM868 GSM modem, with GPS Tracking, motion detection, battery management, wireless connectivity…
79 partsGPL-3.0 - 4 layers40 × 80 mm

- 4 layers124.7 × 64.3 mm

RP2040 SOS band
abhinav937/RP2040_SOS_band
PCB design files for RP2040 based SmartWatch. It features an accelerometer, a GPS module and a cellular module.
107 parts3 - 2 layers52 × 29 mm

Cellular featherwing pcb
keenanjohnson/cellular-featherwing-pcb
The PCB Design for a Cellular Adafruit Featherwing based on the Quectel BG96 LTE Cat M1 & Cat NB1.
64 parts1 - 4 layers26 × 30 mm

Lte m dongle fw
GManSudy/framework-expansion-lte
An LTE-M / NB-IoT cellular modem built into the Framework Laptop Expansion Card form factor, with a native USB-C plug.
32 parts - 4 layers50 × 50 mm

LFX FC R2
nguyencanhanh/luckfox-rv1103-drone
AI quadcopter on one RV1103 (Luckfox Pico Mini B): Linux + RISC-V MCU flight loop, SITL with 3D pilot view, KiCad flight-controller board
142 partsMIT
Questions
How big is the Hw thingcell PCB?
It measures 32.5 × 67 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Hw thingcell use?
101 parts, built around the CH340C, ESP32-S2-SOLO-N8, SIM868 and 1N4448W-7-FS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Hw thingcell KiCad files?
From the GuilleGonzzalez/hw-thingcell repository on GitHub, at the commit this page was made from: the board is hw-thingcell.kicad_pcb and its schematic hw-thingcell.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Hw thingcell design in my own project?
Its repository states no licence, so its author keeps all rights: ask GuilleGonzzalez before reusing the design.