2 layers290.1 × 130 mm
2 layers62.2 × 26.7 mm
Adapter
FalcoGer/FlipperCC11019Adapter for an external CC1101 module for the Flipper Zero
- Size
- 62.2 × 26.7 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 8
- Nets
- 19
- Pads
- 35
- Tracks, vias
- 53, 4
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 29 Aug 2023
- Updated
- 30 Aug 2023
Overview
Adapter is an open-source printed circuit board by FalcoGer, from the FalcoGer/FlipperCC1101 repository on GitHub, published under the MIT licence. It is a 2-layer board of 62.2 × 26.7 mm with 8 parts on 19 nets, routed with 53 tracks and 4 vias.
It is built around the AMS1117-3.3. Its parts include 2 ICs, 1 capacitor, 1 resistor, 1 diode and 1 connector. It belongs with the interfaces and adapters boards of this library.
Main components
1README
README.mdFlipperCC1101
Adapter for an external CC1101 module for the Flipper Zero
How to use:
- Solder on 90° Pin headers to connect to the flipper.
- Solder on a 2x4 pin header onto your CC1101 Module
- Solder on a 470 Ohm resistor and LED (optional)
- Solder on a AMS1117 5V to 3.3V DC to DC step down converter.
- Solder on a capacitor (probably optional)
- Solder the C1101 Module onto this board. (Pin 1 is GND)
- Install Flipper firmware that is capable of using the CC1101 Module (Unleashed or RogueMaster)
- Hack the planet
Images
Render
Front View
Rear View
Parts
8| Qty | Value | Footprint | References |
|---|---|---|---|
| 1 | 470R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 1 | 4C7µ | Capacitor_THT:CP_Radial_D4.0mm_P2.00mm | C1 |
| 1 | AMS1117-3.3 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | U2 |
| 1 | CC1101_Connector | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | U1 |
| 1 | FlipperGPIO | Flipper:FlipperGPIO | J1 |
| 1 | LED | LED_THT:LED_D3.0mm | D1 |
The 6 most common of 8 parts.
Similar boards
- 2 layers26.2 × 45.5 mm
PL18 multiprotocol
pascallanger/DIY-Multiprotocol-TX-Module
Multiprotocol TX Module (or MULTI-Module) is a 2.4GHz transmitter module which controls many different receivers and models.
24 parts1.9kGPL-3.0 - 4 layers99 × 53.3 mm
PSLab
fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io
199 parts1.7kApache-2.0 - 4 layers85 × 56 mm
- 4 layers100 × 54 mm
32Bit shift register
MaltWhiskey/Mega-Cube
16x16x16 PL9823 Cube with Teensy 4.0 and FlexIO driver
64 parts766 - 2 layers44.2 × 29.3 mm
- 2 layers78 × 60 mm
- 2 layers59.1 × 99.9 mm
Cheap FOCer 2 60mm
shamansystems/Cheap-FOCer-2
Low-Cost Motor Controller based on the VESC 6
193 parts407
Questions
How big is the Adapter PCB?
It measures 62.2 × 26.7 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Adapter use?
8 parts, built around the AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Adapter KiCad files?
From the FalcoGer/FlipperCC1101 repository on GitHub, at the commit this page was made from: the board is adapter/adapter.kicad_pcb and its schematic adapter/adapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Adapter design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).