Skip to the content
2 layers121.5 × 60.5 mmRemote, the printed circuit board in 3D

This repository contains the control algorithm for a quadcopter drone on an ESP32 as well as electrical schematics and a pcb design.

Size
121.5 × 60.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
24
Nets
30
Pads
107
Tracks, vias
223, 8
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
8 Jan 2025
Updated
31 Mar 2025

Overview

Remote is an open-source printed circuit board by ElektroJonas, from the ElektroJonas/DIY-Quadcopter repository on GitHub. It is a 2-layer board of 121.5 × 60.5 mm with 24 parts on 30 nets, routed with 223 tracks and 8 vias.

It is built around the ESP32-C3-DEVKITC-02. Its parts include 11 resistors, 5 switches, 2 capacitors, 2 diodes and 1 IC. It belongs with the robots and motor control boards and the ESP32 and RISC-V boards of this library.

Main components

1

README

README.md

Quadcopter Built from Scratch

This project contains all the materials used in building a quadcopter drone. It was part of a project course in electrical engineering and embedded systems at Uppsala University, where we spent a portion of the semester designing and constructing a quadcopter from scratch using off-the-shelf components and some interesting control algorithms! 🚀

Project Demonstration and Summary

Final Result

Below is a figure of the completed drone and its custom-built remote control:

DroneRemote

Control System

The control system consists of two main components: Attitude Control and Altitude Control. Note: Altitude control was not used in the final version of the drone since we didnt get it to work well enough.

  • Attitude Control (angle relative to the ground plane) is implemented using a cascaded PID controller with a Kalman filter and an internal rate control loop. It relies on a low-cost MEMS sensor (gyroscope/accelerometer) for angle estimation.
  • Altitude Control is managed using a pressure sensor in combination with the MEMS sensor for attitude estimation, supplemented by a Zero Velocity Update (ZUPT) algorithm for improved stability and accuracy.

The control system was implemented on an ESP32 microcontroller, utilizing the ESP-NOW protocol for wireless communication.

Full Project Report

A detailed description of this project, including development insights, sources, and useful references for anyone interested in building their own drone, can be found in Quadcopter_final_report.pdf.

Acknowledgments

We would like to express our gratitude to CarbonAeronautics for providing valuable resources that greatly aided the early development of this project.

A special thanks to Uppsala University for sponsoring the project and providing the opportunity to bring this idea to life!

Parts

24
QtyValueFootprintReferences
610kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR5, R6, R7, R8, R10, R11
4390Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1, R2, R3, R4
2802-30110-BJonasLib:JoystickSW1, SW2
2Led_green_and_red_WurthJonasLib:Led green and red WurthD1, D6
2SW_PushButton_Switch_THT:SW_PUSH-12mmSW3, SW4
1100Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR9
1100nCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC1
11uCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC2
1Battery_CellJonasLib:Batterihållare 4xAAABT1
1ESP32-C3-DevKitC-02Espressif:ESP32-C3-DevKitC-02U1
1LOGOLOGOG***
1SpeakerJonasLib:summer 4khz miniatyrLS1
1~JonasLib:Skjutomkopplare 1-pol on-on pcb vinkladSW5

Similar boards

  • 2 layers52.2 × 43.6 mmPCB ESP32-C3-DevKitC-02, the printed circuit board in 3D

    PCB ESP32-C3-DevKitC-02

    vives-project-xp/EOMarkers

    Develop small standalone boxes that light up when someone approaches them. The boxes can be fitted with a plexi with Electronics-ICT and a direction indication via an arrow.

    10 parts3
  • 2 layers98.9 × 44.1 mmShuttle Tracker Node, the printed circuit board in 3D

    Shuttle Tracker Node

    wtg/Shuttle-Tracker-Node

    Resources, schematics, and other information for Shuttle Tracker Node

    27 parts3
  • 2 layers27.9 × 62.4 mmF1 car, the printed circuit board in 3D

    F1 car

    tommasoclini/esp32_f1

    esp32 f1 car

    2 parts2MIT
  • 2 layers49.2 × 40.2 mmPcb 1 new, the printed circuit board in 3D

    Pcb 1 new

    Haridharan-D/eSim_PCB_Design_Project_Files

    Battery-powered ESP32 air quality monitor with a soft power latch, MCP16251 boost converter, and ADS1115 ADC — implemented and simulated in eSim.

    20 partsGPL-3.0
  • 2 layers49.3 × 66.5 mmHeishamon lr pdc, the printed circuit board in 3D

    Heishamon lr pdc

    lrodorigo/heishamon-lr-aquarea-board

    A simple alternative hardware implementation for the great HeishaMon board for communicating with Panasonic heatpumps

    30 parts
  • 2 layers63.3 × 45.5 mmSd bt streamer, the printed circuit board in 3D

    Sd bt streamer

    pluggee/G3X_SD_BT

    SD card streamer

    7 partsGPL-3.0
  • 2 layers121.5 × 60.5 mmRemote, the printed circuit board in 3D

    Remote

    Siggeaxe/DIY_Quadcopter

    Cool Quadcopter UAV built from scratch!

    26 parts
  • 2 layers100 × 80 mmKnock knock esp32, the printed circuit board in 3D

    Knock knock esp32

    Universumgames/knock-knock-esp32

    A knock pattern recognition with esp32

    26 partsCC-BY-4.0

Questions

How big is the Remote PCB?

It measures 121.5 × 60.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Remote use?

24 parts, built around the ESP32-C3-DEVKITC-02. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Remote KiCad files?

From the ElektroJonas/DIY-Quadcopter repository on GitHub, at the commit this page was made from: the board is Schematics and PCB Designs/Remote/Remote.kicad_pcb and its schematic Schematics and PCB Designs/Quadcopter/Quadcopter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Remote design in my own project?

Its repository states no licence, so its author keeps all rights: ask ElektroJonas before reusing the design.