Skip to the content
2 layers99.1 × 87.6 mmProject Supernova PCB, the printed circuit board in 3D

A Helium Network Helium Balloon

Size
99.1 × 87.6 mm
Copper layers
2
Thickness
0.82 mm
Parts
65
Nets
66
Pads
214
Tracks, vias
295, 60
Pours
166
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
18 Mar 2023
Updated
31 Dec 2023

Overview

Project Supernova PCB is an open-source printed circuit board by DeflateAwning, from the DeflateAwning/project-supernova-balloon-pcb repository on GitHub, published under the MIT licence. It is a 2-layer board of 99.1 × 87.6 mm with 65 parts on 66 nets, routed with 295 tracks and 60 vias.

It is built around the LORA-E5-HF, STDS75DS2F and AO3420. Its parts include 15 resistors, 15 connectors, 8 capacitors, 6 ICs and 4 diodes. It belongs with the ESP32 boards of this library.

Main components

3

README

README.md

Project Supernova

A Helium Balloon, to assess the Helium Network.

Features

This project is a PCB which is capable of being the primary payload on a PCB aboard a stratospheric helium balloon. The PCB intends to downlink

  • Onboard GPS for position tracking
  • Atmospheric condition sensors (temperature/pressure/humidity) to generate downlink data
  • Onboard PID-controlled heater and battery management
  • Very low cost (<$100)

Notes

  • 3v3 regulated voltage. 9v unregulated battery voltage.

Rev 2 Errata

  1. Nothing yet (fingers crossed)

Rev 1 Errata

  1. DHT22 doesn't support 3V3 supply, technically
  2. ADC2 doesn't work when wifi is enabled
  3. DHT22 cannot be connected to pin D12, as D12 must be floating at boot
  4. D34-D39 are input-only (so TEMP_V+ is a problem)
  5. LM335 onboard temperature sensor is basically incompatible with 3V3 systems
  6. DHT22 needs a 10k pull-up to 3V3
  7. RTF switch needs resistors on each leg to prevent shorting in case of a make-before-break switch.
  8. The voltage regulator footprint could use the pads moved a bit (and could include through-hole pins).
  9. Should've added a pull-down resistor to the heater MOSFET to prevent heating during boot.
  10. Shouldn't have put a via in the pad on the MOSFET, as it prevented the gate from soldering right, then burned the MOSFET when it entered the linear region. Should've used way larger pads on the hand-soldered SOT-23 MOSFET.

Changes made to correct errata items (Rev 1.1)

  • DHT22 (DHT_DATA) now connected to D23 (per Errata #3).
  • DHT22 now has a 10k pull-up to 3V3 (Errata #6).
  • TEMP_V+ now connected to D25 (per Errata #4), and still left connected to D35.
  • LM335 onboard temperature sensor is unused.

OFIs

  • Add LED on HEATER_EN net
  • Add LED polarity on silk screen
  • Consider 10u cap from GND to EN for programming
  • D2 is the onboard LED, so probably best to not use it
  • Should have referenced this doc: https://randomnerdtutorials.com/esp32-pinout-reference-gpios/
  • Add jumper to disconnect power from GPS (because it uses so much power)

Parts

65
QtyValueFootprintReferences
8MountingHoleMountingHole:MountingHole_2mmH5, H6, H7, H8, H9, H10, H11, H12
6Conn_01x04Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ1, J2, J3, J13, J14, J15
54.7kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR5, R6, R7, R13, R14
4LEDLED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolderD1, D2, D3, D4
4MountingHole_PadMountingHole:MountingHole_3.2mm_M3_DIN965_PadH1, H2, H3, H4
4Screw_Terminal_01x02TerminalBlock:TerminalBlock_bornier-2_P5.08mmJ6, J7, J11, J12
310uCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC6, C7, C8
31kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR8, R9, R15
2100k_ThermistorConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ5, J8
23.3kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR10, R12
275kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR2, R3
2Conn_01x02Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ9, J10
2NCCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC4, C5
2SW_SPDTButton_Switch_THT:SW_Slide_1P2T_CK_OS102011MS2QSW1, SW2
10Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR1
10Inductor_SMD:L_1206_3216Metric_Pad1.42x1.75mm_HandSolderL1
1100nCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC2
1100uCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC1
110kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR11
118kResistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolderR4
14.7uCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC3
1AO3420Project-Supernova-Footprint-Lib:SOT-23-MassivePads-HandSolderQ1
1BMP280-ModuleProject-Supernova-Footprint-Lib:BMP280-ModuleU2
1Conn_CoaxialConnector_Coaxial:SMA_Wurth_60312002114503_VerticalJ4
1ESP32-Module-30PinProject-Supernova-Footprint-Lib:ESP32-Module-30PinU5
1GY-NEO6MV2-ModuleProject-Supernova-Footprint-Lib:GY-NEO6MV2-ModuleU1
1LoRa-E5Project-Supernova-Footprint-Lib:LoRa-E5_HandSolderU3
1S09Project-Supernova-Footprint-Lib:S09U6
1STDS75DS2FPackage_SO:MSOP-8_3x3mm_P0.65mmU4
1TestPointTestPoint:TestPoint_Pad_D3.0mmTP1

Similar boards

  • 4 layers79 × 81 mmBIRDS X PCB, the printed circuit board in 3D

    BIRDS X PCB

    AlbertaSat/BIRDS-X_PCB

    Repository for the PCB design for the BIRDS-X project

    162 parts1CERN-OHL-P-2.0
  • 2 layers52 × 67 mmTbogg Sensor Pkg PCB, the printed circuit board in 3D

    Tbogg Sensor Pkg PCB

    UofC-GNCTR-2024/Tbogg-Sensor-Package-PCB

    The sensor package (strain, temperature, vibration) for the 2024 UofC GNCTR tbogg. Designed as an R&D intrastructure monitoring solution.

    48 parts1MIT
  • 11 layers44.6 × 31.6 mmNotecarrier Micro, the printed circuit board in 3D

    Notecarrier Micro

    Safecast/bGeigieZen

    bGiegieZen an Open Source Geiger Counter.

    33 parts24
  • 4 layers65 × 65 mmProjekt, the printed circuit board in 3D

    Projekt

    jegor377/mini-car

    Mini rc car

    119 parts
  • 2 layers38.2 × 27.8 mmRGB strip, the printed circuit board in 3D

    RGB strip

    kikeelectronico/rgb-strip-controller

    A PCB design to control a RGBW strip

    18 parts
  • 2 layers52 × 56.6 mmMuMo v2-Node, the printed circuit board in 3D

    MuMo v2-Node

    Strooom/MuMo-V2-Node-PCB

    PCB design for the Museum Monitor V2

    79 parts17
  • 2 layers115 × 80 mmWheather board v1, the printed circuit board in 3D

    Wheather board v1

    nbreard/mellia

    https://www.mellia.fr/

    69 parts11
  • 2 layers77 × 51.4 mmMZ2023, the printed circuit board in 3D

    MZ2023

    makezurich/makezurich-badge-2023

    Repo for the badge, hardware, software and examples.

    91 parts4MIT

Questions

How big is the Project Supernova PCB PCB?

It measures 99.1 × 87.6 mm and has 2 copper layers, 0.82 mm thick.

What parts does the Project Supernova PCB use?

65 parts, built around the LORA-E5-HF, STDS75DS2F and AO3420. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Project Supernova PCB KiCad files?

From the DeflateAwning/project-supernova-balloon-pcb repository on GitHub, at the commit this page was made from: the board is Project-Supernova-PCB/Project-Supernova-PCB.kicad_pcb and its schematic Project-Supernova-PCB/LoRa_Module.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Project Supernova PCB design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).