

RGB strip
A PCB design to control a RGBW strip
- Size
- 38.2 × 27.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 18
- Nets
- 26
- Pads
- 75
- Tracks, vias
- 218, 11
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 26 Mar 2021
- Updated
- 27 Mar 2021
Overview
RGB strip is an open-source printed circuit board by kikeelectronico, from the kikeelectronico/rgb-strip-controller repository on GitHub. It is a 2-layer board of 38.2 × 27.8 mm with 18 parts on 26 nets, routed with 218 tracks and 11 vias.
It is built around the ESP-12E, AO3420 and 1TS002E-2500-2500-CT, with the TJ-S1615SW6TGLCBG-A5 among its other parts. Its parts include 5 resistors, 4 transistors, 3 connectors, 2 capacitors and 2 ICs. It belongs with the lEDs and displays boards and the ESP8266 boards of this library.
Main components
4ESP-12E
SMD,24x16mm-20℃~+70℃ -90dBm 16dBm 170mA 2.4GHz 3V~3.6V 56mA 802.11b/g/n ESP8266 Chip On-board PCB Antenna Over-the-air (OTA) update UART、SPI、I2C SMD,24x16mm WiFi Modules ROHSAi-ThinkerWiFi ModulesAO3420
SOT-23MOSFETsTWGMC1TS002E-2500-2500-CT
SMD,6.1x3.7mm-40℃~+90℃ 12V 2.5N 2.5mm 3.7mm 30,000 Cycles 50mA 6.1mm Gull Wing No Rectangular Button Red SPST Surface Mount,Vertical Without Bracket SMD,6.1x3.7mm Tactile Switches ROHSHYPTactile SwitchesTJ-S1615SW6TGLCBG-A5
SMD-4P,1.6x1.5mm-40℃~+80℃ 108mW 120° 160mcd、500mcd 2.8V~3.4V 20mA 460nm~470nm、520nm~530nm 460nm、535nm Discrete Diode Emerald Green, Blue Water Clear SMD-4P,1.6x1.5mm LED Indication - Discrete ROHSTOGIALEDLED Indication - Discrete
README
README.mdView this project on CADLAB.io.
RGB Strip controller

RGB strip controller by Enrique Gómez licensed by Creative Commons Attribution-ShareAlike 4.0 International License.
Parts
18| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | AO3420 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R2, R3 |
| 2 | 19R1 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R4, R5 |
| 2 | 330nF | Capacitor_SMD:C_0603_1608Metric | C1, C2 |
| 1 | 1TS002E-2500-2500-CT | Button_Switch_SMD:SW_SPST_CK_RS282G05A3 | SW1 |
| 1 | Barrel_Jack_Switch | Connector_BarrelJack:BarrelJack_Wuerth_6941xx301002 | J1 |
| 1 | Conn_01x06_Female | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J3 |
| 1 | ESP-12E | RF_Module:ESP-12E | U2 |
| 1 | LED | Connector_Molex:Molex_KK-254_AE-6410-05A_1x05_P2.54mm_Vertical | J2 |
| 1 | MC33275DT-3.3RKG | Package_TO_SOT_SMD:TO-252-2 | U1 |
| 1 | TJ-S1615SW6TGLCBG-A5 | RGB strip local:TJ-S1615SW6TGLCBG-A5 | D2 |
Similar boards
- 11 layers44.6 × 31.6 mm

- 4 layers79 × 81 mm

BIRDS X PCB
AlbertaSat/BIRDS-X_PCB
Repository for the PCB design for the BIRDS-X project
162 parts1CERN-OHL-P-2.0 - 2 layers99.1 × 87.6 mm

Project Supernova PCB
DeflateAwning/project-supernova-balloon-pcb
A Helium Network Helium Balloon
65 partsMIT - 4 layers65 × 65 mm

- 2 layers33.7 × 97.8 mm

HAN ESP TSS721
UtilitechAS/amsreader-firmware
ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported
29 parts470 - 2 layers43 × 34.3 mm

- 2 layers25.6 × 23 mm

Breakout
skorokithakis/tiny-ESP8266-breakout
A very small and basic ESP8266 breakout board
12 parts115BSD-2-Clause - 2 layers104.8 × 72.1 mm

SST V2 4
mcbittech/souliss-smart-thermostat-WiFi
ESP8266 WiFi Smart Thermostat based on Souliss IoT Framework
53 parts110GPL-2.0
Questions
How big is the RGB strip PCB?
It measures 38.2 × 27.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the RGB strip use?
18 parts, built around the ESP-12E, AO3420, 1TS002E-2500-2500-CT and TJ-S1615SW6TGLCBG-A5. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the RGB strip KiCad files?
From the kikeelectronico/rgb-strip-controller repository on GitHub, at the commit this page was made from: the board is Kicad/RGB_strip/RGB_strip.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the RGB strip design in my own project?
Its repository states no licence, so its author keeps all rights: ask kikeelectronico before reusing the design.