2 layers52.7 × 29.8 mm
2 layers69.9 × 33 mm
RocketServo
DavidMFlynn/Rocket-Servo1Altimeter triggered 2 position servo driver
- Size
- 69.9 × 33 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 56
- Nets
- 45
- Pads
- 151
- Tracks, vias
- 317, 41
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 29 Sep 2022
- Updated
- 20 Oct 2026
Overview
RocketServo is an open-source printed circuit board by DavidMFlynn, from the DavidMFlynn/Rocket-Servo repository on GitHub, published under the MIT licence. It is a 2-layer board of 69.9 × 33 mm with 56 parts on 45 nets, routed with 317 tracks and 41 vias.
It is built around the PIC16F1847-I/SO and CPC1017N. Its parts include 23 resistors, 10 capacitors, 8 ICs, 8 diodes and 5 connectors. It belongs with the PIC boards of this library.
Main components
2
PIC16F1847-I/SO
SOIC-18-300mil-40℃~+85℃ 1.8V~5.5V 10bit 14KB 15 1KB 256Byte 32MHz 8 Bit Built-in FLASH PIC SOIC-18-300mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
CPC1017N
SOP-4-2.54mm1.2V 1.5kV 100mA 10ms 10ms 16Ω 60V One set normally open: 2A (SPST - normally open) SOP-4-2.54mm Solid State Relays (MOS Output) ROHSLittelfuse/IXYSSolid State Relays (MOS Output)
README
README.mdRocket-Servo
Altimeter triggered 2 position servo driver
Parts
56| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | .1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C3, C4, C6, C7, C8, C9, C10 |
| 6 | 1K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R11, R16, R20, R21, R22 |
| 6 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | LED1, P1, P2, P3, P4, P5 |
| 5 | CPC1017N | Package_SO:SOP-4_3.8x4.1mm_P2.54mm | U3, U4, U6, U7, U8 |
| 4 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R23, R24, R25 |
| 4 | 220R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R13, R14, R15 |
| 4 | 470R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R17, R18, R19 |
| 4 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | P6, P7, P8, P9 |
| 2 | 47K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R7 |
| 2 | SW_Push | Resistor_SMD:R_1206_3216Metric | SW1, SW2 |
| 1 | 1K0 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R12 |
| 1 | 220uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C5 |
| 1 | 22K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R10 |
| 1 | 270 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R9 |
| 1 | 33uF | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C2 |
| 1 | Conn_01x05 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J1 |
| 1 | L7806 | Package_TO_SOT_SMD:TO-263-2 | U1 |
| 1 | L78L05_SOT89 | Package_TO_SOT_SMD:SOT-89-3 | U2 |
| 1 | LED | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D2 |
| 1 | PIC16F1847-I/SO | Package_SO:SOIC-18W_7.5x11.6mm_P1.27mm | U5 |
| 1 | SMB | Diode_SMD:D_SMA | D1 |
More from DavidMFlynn/Rocket-Servo
4- 2 layers60.3 × 14.6 mm
- 2 layers60.3 × 14.6 mm
- 2 layers10.2 × 6.3 mm
Similar boards
- 2 layers165.1 × 66 mm
Selector8x16
DavidMFlynn/VideoSelector
Sets camera to monitor connections, RS-232, Extron Electronics MAV 88, PIC16F1847.
113 parts1GPL-3.0 - 2 layers90 × 95 mm
Xt60 parallelizer
limpkin/xt60_parallelizer
a custom board to monitor custom battery packs
57 parts16MIT - 2 layers161.3 × 88.5 mm
- 2 layers
GCAN gauge
willemcvu/gCAN-gauge
An open-source ESP32-based programmable digital gauge targeted at EV conversions
49 parts4MIT - 4 layers100 × 100 mm
AFE
Blaze-Pascal/Masters-Multi-Channel_DAQ
Custom 2-channel digital oscilloscope DAQ with 20MHz bandwidth. Built with a custom KiCad analog front-end (AFE) PCB, Gowin FPGA (Tang Nano 9K) for high-speed signal buffering (VHDL), and an RPi Pico MCU for SCPI-like…
216 parts2GPL-3.0 - 4 layers67 × 157 mm
- 6 layers56.7 × 54.7 mm
Better md80
darshp848/bldc-controller-60v
60 V, 20 A / 80 A peak BLDC motor controller that fits the MD80 v3.0 mounting. KiCad 10, 6 layers.
144 parts1 - 4 layers100 × 100 mm
Questions
How big is the RocketServo PCB?
It measures 69.9 × 33 mm and has 2 copper layers, 1.6 mm thick.
What parts does the RocketServo use?
56 parts, built around the PIC16F1847-I/SO and CPC1017N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the RocketServo KiCad files?
From the DavidMFlynn/Rocket-Servo repository on GitHub, at the commit this page was made from: the board is PCB RS4 Rev nc/RocketServo.kicad_pcb and its schematic PCB RS2 Rev nc/RocketServo.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the RocketServo design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).