

Réalisation d'un bras robotique 6 axes pour la majeure SRD (Systèmes Robotiques et Drones) — EFREI Paris.
- Size
- 42 × 42 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 55
- Nets
- 73
- Pads
- 220
- Tracks, vias
- 588, 117
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 22 Jun 2026
- Updated
- 29 Jul 2026
Overview
BRAS is an open-source printed circuit board by Corentin-k, from the Corentin-k/BRAS_ROBOTIQUE repository on GitHub. It is a 4-layer board of 42 × 42 mm with 55 parts on 73 nets, routed with 588 tracks and 117 vias.
It is built around the STM32G431CBT6, AS5047P-ATSM and TMC2209-LA-T. Its parts include 20 capacitors, 11 resistors, 6 connectors, 5 ICs and 4 diodes. It belongs with the STM32 boards of this library.
Main components
3STM32G431CBT6
LQFP-48(7x7)-40℃~+85℃ 1.71V~3.6V 128KB 12bit 12bit 170MHz 32 Bit 32KB 38 ARM Cortex-M4F Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)AS5047P-ATSM
TSSOP-14_4.4x5.0x0.65P-40℃~+125℃ 0°~360° 1.2mm 15mA 4.4mm 4.5V~5.5V 5mm Magnetic rotary position sensor No SPI TSSOP-14 Position Sensors ROHSAdvanced Monolithic SystemsPosition SensorsTMC2209-LA-T
QFN-28-EP(5x5)-40℃~+125℃ 2 256、8、16、32、64 2A 340mΩ 4.75V~29V 4.75V~29V Bipolar Driver Overcurrent Protection、Short-Circuit Protection、Over temperature protection、Under-voltage lockout、Motor step-out prevention function、Built-in charge pump、Thermal warning STEP/DIR、UART Yes QFN-28-EP(5x5) Stepper Motor Driver ROHSTRINAMIC Motion Control GmbHStepper Motor Driver
README
README.md🦾 Bras Robotique 6 Axes
Réalisation d'un bras robotique 6 axes pour la majeure SRD (Systèmes Robotiques et Drones) — EFREI Paris.
Bras motorisé par 6 moteurs NEMA pilotés chacun par un driver dédié, communicants entre eux via un bus CAN FD.
📂 Structure du dépôt
.
├── BRAS_KICAD/ # Schéma & PCB du driver moteur (KiCad 8)
│ ├── components/ # Empreintes & symboles custom
│ └── production/ # Fichiers de fabrication (Gerber, BOM, positions)
├── BRAS_STM32/ # Firmware STM32G431 (STM32CubeIDE)
│ ├── Core/ # Sources applicatives (main, périphériques)
│ └── Drivers/ # HAL STM32G4xx
└── README.md🔌 DRIVER (KiCad)
Chaque axe du bras est piloté par une carte driver identique. Les 6 cartes sont chaînées par bus CAN FD et alimentées en 24 V.
Composants principaux
| Composant | Référence | Rôle |
|---|---|---|
| MCU | STM32G431CBT6 (LQFP-48) | Microcontrôleur ARM Cortex-M4, gestion FDCAN, SPI, I2C, UART, PWM |
| Driver moteur | TMC2209-LA-T (QFN-28) | Driver pas-à-pas silencieux avec StealthChop / SpreadCycle |
| Encodeur | AS5047P-ATSM (SOIC-14) | Encodeur magnétique absolu 14 bits, interface SPI |
| Transceiver CAN | SN65HVD230DR (SOIC-8) | Transceiver CAN 3.3 V pour bus FDCAN |
| Régulateur | AP63203WU-7 (SOIC) | Buck DC-DC 24 V → 3.3 V, 2 A |
| MOSFET | AO4407A | Protection / commutation d'alimentation |
Jumpers & boutons
- Jumper résistance de terminaison — 120 Ω sur le bus FDCAN (à activer sur le premier et le dernier driver de la chaîne)
- Jumper 3V3 — Sélection de l'alimentation 3.3 V via STLINK pour la programmation
- DIP Switch x2 — BTN1 / BTN2 pour le paramétrage (adresse CAN, mode, etc.)
- Boutons poussoirs — BOOT / RESET
LEDs
| LED | Couleur | Fonction |
|---|---|---|
| LED 3V3 | 🔴 Rouge | Indicateur d'alimentation 3.3 V |
| LED paramétrage | 🔵 Bleue | Retour utilisateur / état |
| LED paramétrage | 🟢 Verte | Retour utilisateur / état |
Architecture de communication
┌─────────┐ CAN FD ┌─────────┐ CAN FD ┌─────────┐
│ Driver 1 │◄──────────►│ Driver 2 │◄──────────►│ Driver 3 │ ...
│ (Base) │ │ (Épaule)│ │ (Coude) │
└─────────┘ └─────────┘ └─────────┘
▲ │
│ FDCAN_H / FDCAN_L │
│ + GND + 24V │
└──────── Résistance 120Ω ──── ... ────────────┘⚠️ Le premier driver de la chaîne doit supporter l'appel de courant total :
I_moteur × N_moteurssur l'entrée 24 V.
Périphériques STM32 utilisés
Le firmware (projet STM32CubeIDE dans BRAS_STM32/) configure les périphériques suivants :
- FDCAN1 — Bus CAN FD pour la communication inter-drivers
- SPI1 — Lecture de l'encodeur AS5047P
- I2C1 — Extension / capteurs additionnels
- TIM1 — Génération PWM pour le TMC2209 (STEP/DIR)
- USART1 — Debug série / configuration TMC2209 (UART single-wire)
- GPIO — LEDs, boutons, enable driver, jumpers
Parts
55| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100nF | Capacitor_SMD:C_0603_1608Metric | C5, C9, C10, C11, C12, C19 |
| 4 | Mounting_Holes:MountingHole_3.2mm_M3 | , , , | |
| 4 | 1k | Resistor_SMD:R_0603_1608Metric | R4, R10, R11, R12 |
| 3 | 100n | Capacitor_SMD:C_0603_1608Metric | C2, C3, C15 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric | R5, R14, R15 |
| 3 | LED | LED_SMD:LED_0603_1608Metric | D1, D2, D3 |
| 2 | 0.11 | Resistor_SMD:R_1206_3216Metric | R6, R8 |
| 2 | 100p | Capacitor_SMD:C_0603_1608Metric | C13, C14 |
| 2 | 22u | Capacitor_SMD:C_0805_2012Metric | C6, C7 |
| 2 | SW_SPST | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KMR2 | SW2, SW3 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 100n 16v | Capacitor_SMD:C_0603_1608Metric | C21 |
| 1 | 100u | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C16 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | 120 | Resistor_SMD:R_0603_1608Metric | R16 |
| 1 | 1u | Capacitor_SMD:C_0603_1608Metric | C18 |
| 1 | 2.2u 6.3v | Capacitor_SMD:C_0603_1608Metric | C22 |
| 1 | 22n 50v | Capacitor_SMD:C_0603_1608Metric | C8 |
| 1 | 4.7u | Inductor_SMD:L_Taiyo-Yuden_NR-40xx | L1 |
| 1 | 4.7u | Capacitor_SMD:C_0603_1608Metric | C17 |
| 1 | AP63203WU-7 | AP63203WU-7:SOIC_05WU-7_DIO-M | U4 |
| 1 | AS5047P-ATSM | AS5047P-ATSM:SOP65P640X120-14N | U3 |
| 1 | CAN_IN | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MPT-0,5-4-2.54_1x04_P2.54mm_Horizontal | J7 |
| 1 | CAN_OUT | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MPT-0,5-4-2.54_1x04_P2.54mm_Horizontal | J8 |
| 1 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | Conn_01x06_Pin | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | D_TVS | Diode_SMD:D_SMC | D4 |
| 1 | JUMPER | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | Jumper_3_Open | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP1 |
| 1 | MOTOR | Connector_JST:JST_PH_S4B-PH-K_1x04_P2.00mm_Horizontal | J5 |
| 1 | STM32G431CBT6 | LQFP48-7x7mm:LQFP48-7x7mm | U1 |
| 1 | SW_DIP_x02 | Button_Switch_THT:SW_DIP_SPSTx02_Slide_9.78x7.26mm_W7.62mm_P2.54mm | SW1 |
| 1 | TCAN332GDR | TCAN332GDR:SOIC127P599X175-8N | U5 |
| 1 | TMC2209-LA-T | TMC2209-LA-T:QFN50P500X500X90-29N | U2 |
Similar boards
- 4 layers42 × 42 mm

- 2 layers189.5 × 204.9 mm

SmartSpin2k Panelized
doudar/SmartSpin2k
Transform your spin bike into a Smart Trainer!
749 parts292GPL-2.0 - 4 layers170 × 100 mm

Leviathan V1.3
MotorDynamicsLab/Leviathan
Leviathan Main Controller for Voron 2 / Trident 3D Printers
420 parts124GPL-3.0 - 4 layers67 × 15 mm

GBB15
skuep/GBB15
A gantry-mounted CAN stepper driver board for 15mm aluminum beams (mostly for PrintersForAnts printers). This is heavily work in progress.
76 parts51MIT - 4 layers187.9 × 60.2 mm

MotionModuleSTM32F103R8
griffotron/MotionModuleSTM32R8
PCB design and code for the STM32 powered Motion Module that controls 14 stepper motors
246 parts13MIT - 4 layers88.4 × 63.6 mm

Compute
hstarmans/firestarter
Kicad design files for prism laser direct imager using up5k FPGA and ESP32
125 parts13 - 4 layers100 × 100 mm

Labathome pcb
klaus-liebler/labathome
Der kleine Bruder von lab@home. Ermöglicht das Experimentieren mit PT1...PTn-Gliedern, die intern als RC-Kombination (entkoppelt über Operationsverstärker) ausgeführt sind.
292 parts5MIT - 4 layers42 × 42 mm

Stepper driver
janelia-kicad/stepper_driver
Motor mounted stepper driver with step and direction controls and a UART interface
43 parts3
Questions
How big is the BRAS PCB?
It measures 42 × 42 mm and has 4 copper layers, 1.6 mm thick.
What parts does the BRAS use?
55 parts, built around the STM32G431CBT6, AS5047P-ATSM and TMC2209-LA-T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the BRAS KiCad files?
From the Corentin-k/BRAS_ROBOTIQUE repository on GitHub, at the commit this page was made from: the board is BRAS_KICAD/BRAS.kicad_pcb and its schematic BRAS_KICAD/BRAS.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the BRAS design in my own project?
Its repository states no licence, so its author keeps all rights: ask Corentin-k before reusing the design.