

M0118 integrated usb
Drop-in replacement USB-C PCB for the Apple M0118 powered by QMK and VIAL.
- Size
- 372.1 × 113.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 192
- Nets
- 124
- Pads
- 462
- Tracks, vias
- 604, 97
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 28 Apr 2022
- Updated
- 3 Jul 2023
Overview
M0118 integrated usb is an open-source printed circuit board by Cipulot, from the Cipulot/m0118_integrated_usb repository on GitHub, published under the MIT licence. It is a 2-layer board of 372.1 × 113.8 mm with 192 parts on 124 nets, routed with 604 tracks and 97 vias.
It is built around the ATMEGA32U4-MU and PRTR5V0U2X. Its parts include 83 diodes, 7 capacitors, 6 resistors, 3 connectors and 1 IC. It belongs with the keyboards and input boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
2ATMEGA32U4-MU
VQFN-44-EP(7x7)-40℃~+85℃ 10bit 16MHz 1KB 2.5KB 2.7V~5.5V 26 32KB 8 Bit AVR Built-in FLASH VQFN-44-EP(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)PRTR5V0U2X
SOT-143-55℃~+125℃ 0.3pF、0.8pF 100W 10V、15V 5V 6.5V 6A 80nA ESD IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Three channels Unidirectional SOT-143 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)
README
README.mdm0118_integrated_usb
Drop-in replacement USB-C PCB for the Apple M0118 powered by QMK and VIAL.



Daughterboard
The board comes with a snappable daughterboard with onboard USB-C. To avoid extra costs no connector is used. Instead the user will solder wires accordingly to the pin correspondence (marked on the PCB).

Internal Wire
Internal wiring of a USB cable is possible. For this reason 2 holes on the pcb are available to the user. You can use them to tie down the cable using a zip tie for added stability.
An extra pin is provided, the Shiled pin. This is electrically connected to the board GND and it's solely used to avoid clipping the shielding wire off from the cable (if present at all).


hahahahaha funny QR
Firmware
Firmware is in development. Keep an eye out on the commits for it.
Firmware is OUT!! Precompiled VIAL .hex file downloadable here.
Parts
192| Qty | Value | Footprint | References |
|---|---|---|---|
| 82 | D | Diode_SMD:D_SOD-123 | D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23, D24 +66 |
| 69 | MX-NoLED | cipulot_parts:ALPS-1U | MX1, MX2, MX10, MX11, MX12, MX13, MX15, MX16, MX17, MX18, MX20, MX21, MX22, MX23, MX24, MX25 +53 |
| 3 | 0.1u | Capacitor_SMD:C_0805_2012Metric | C1, C2, C3 |
| 3 | MX-NoLED | cipulot_parts:ALPS-1.75U | MX37, MX73, MX76 |
| 3 | MX-NoLED | cipulot_parts:ALPS-1.5U | MX14, MX19, MX72 |
| 3 | MX-NoLED | cipulot_parts:ALPS-1.25U | MX54, MX66, MX71 |
| 2 | 10k | Resistor_SMD:R_0805_2012Metric | R3, R4 |
| 2 | 22 | Resistor_SMD:R_0805_2012Metric | R1, R2 |
| 2 | 22p | Capacitor_SMD:C_0805_2012Metric | C5, C7 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R5, R6 |
| 2 | MX-NoLED | cipulot_parts:ALPS-2U | MX80, MX82 |
| 2 | MountingHole | cipulot_parts:HOLE_M2 | H22, H22 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric | C4 |
| 1 | 16MHz | cipulot_parts:Crystal_SMD_3225-4pin_3.2x2.5mm | Y1 |
| 1 | 1u | Capacitor_SMD:C_0805_2012Metric | C6 |
| 1 | 500mA | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | ATmega32U4-M | Package_DFN_QFN:QFN-44-1EP_7x7mm_P0.5mm_EP5.2x5.2mm | U1 |
| 1 | AVR-ISP-6-Connector | cipulot_parts:Reset_Pretty | J1 |
| 1 | HRO-TYPE-C-31-M-12 | cipulot_parts:HRO-TYPE-C-31-M-12-Assembly | USB1 |
| 1 | LOGO | custom_parts:qmk | G*** |
| 1 | LOGO | cipulot_parts:IronMan | G*** |
| 1 | LOGO | LOGO | G*** |
| 1 | LOGO | custom_parts:vial_logo | G*** |
| 1 | MX-NoLED | cipulot_parts:ALPS-5.25U | MX75 |
| 1 | MX-NoLED | cipulot_parts:ALPS-SMALL-ISO | MX32 |
| 1 | PRTR5V0U2X | Package_TO_SOT_SMD:SOT-143 | D1 |
| 1 | SW_Push | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | SW1 |
| 1 | USB | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J2 |
| 1 | USB_DB | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
Similar boards
- 2 layers344 × 124.5 mm

- 2 layers285 × 95.1 mm

- 2 layers285 × 95.1 mm

- 2 layers284.3 × 116.2 mm

- 2 layers285.7 × 95.5 mm

Jones
jpskenn/Jones
Row-staggered 60% keyboard with gapless R2-R3 row. GH60 case compatible.
249 parts12MIT - 2 layers285 × 95.1 mm

Nora
jpskenn/Nora
Narrow pitch keyboard with Choc switches and keycaps. GH60 compatible.
303 parts12MIT - 2 layers209.6 × 76.2 mm

Didaktik
calvin-mcd/Didaktik-40
a 40s keyboard inspired by the Didaktik computer & keyboard
129 parts9GPL-3.0 - 2 layers228.4 × 85 mm

LeChiffre
paindrivendev/le-yiffre
Le Yiffre is a modified hotswap Le Chiffre pcb as an experimental design with different thumb clusters.Thanks to tominabox1 for creating Le Chiffre Keyboard and making it open source.
108 parts8
Questions
How big is the M0118 integrated usb PCB?
It measures 372.1 × 113.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the M0118 integrated usb use?
192 parts, built around the ATMEGA32U4-MU and PRTR5V0U2X. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the M0118 integrated usb KiCad files?
From the Cipulot/m0118_integrated_usb repository on GitHub, at the commit this page was made from: the board is PCB/m0118_integrated_usb.kicad_pcb and its schematic PCB/m0118_integrated_usb.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the M0118 integrated usb design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).