2 layers171.5 × 106.7 mm
Sequencer
westlicht/performer-hardware
PER|FORMER Eurorack Sequencer - Hardware Design Files
435 parts110
2 layers50.8 × 19 mm
Esp-4digit display
CRImier/IMTAIDKW1I Made This And I Don't Know Why - ESP-12 board with a 4-digit 7-segment display
- Size
- 50.8 × 19 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 21
- Nets
- 23
- Pads
- 78
- Tracks, vias
- 179, 34
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 20 Jun 2017
- Updated
- 4 Nov 2019
Overview
Esp-4digit display is an open-source printed circuit board by CRImier, from the CRImier/IMTAIDKW repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 50.8 × 19 mm with 21 parts on 23 nets, routed with 179 tracks and 34 vias.
It is built around the 74HC595 and LM1117-3.3. Its parts include 5 resistors, 3 capacitors, 3 ICs and 2 switches. It belongs with the lEDs and displays boards and the ESP8266 boards of this library.
Main components
2
74HC595
SOP-16-40℃~+85℃ 1 100ns@5V,50pF 10MHz 2V~6V 74HC 8 Serial-to-Serial or Parallel Tri-State SOP-16 Shift Registers ROHSGRShift Registers
LM1117-3.3
SOT-2231 1.3V@(1000mA) 15V 1A 2mA 3.3V Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHShongjiachengUncategorised
README
README.mdIMTAIDKW
I Made This And I Don't Know Why - ESP-12 board with a 4-digit 7-segment display
Parts
21| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 10K | Resistors_SMD:R_0603_HandSoldering | R1, R2, R3, R4, R5 |
| 1 | 100nF | Capacitors_SMD:C_0805_HandSoldering | C2 |
| 1 | 100uF | Capacitors_Tantalum_SMD:CP_Tantalum_Case-C_EIA-6032-28_Hand | C3 |
| 1 | 3V3 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | W5 |
| 1 | 5V | Wire_Pads:SolderWirePad_2x_2mmDrill | W3 |
| 1 | 74HC595 | Housings_SOIC:SOIC-16_3.9x9.9mm_Pitch1.27mm | U3 |
| 1 | ADC | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | W1 |
| 1 | CA56-12 | Displays_7-Segment:Cx56-12 | AFF1 |
| 1 | C_Small | Capacitors_SMD:C_0805_HandSoldering | C1 |
| 1 | ESP-12 | footprints:ESP-12 | U2 |
| 1 | GND | Wire_Pads:SolderWirePad_2x_2mmDrill | W4 |
| 1 | GND | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | W2 |
| 1 | GP0 | footprints:SW_SPST_EVQPE1 | SW1 |
| 1 | GP2 | Measurement_Points:Measurement_Point_Round-SMD-Pad_Small | W6 |
| 1 | JUMPER | Connect:GS2 | JP1 |
| 1 | LM1117-3.3 | TO_SOT_Packages_SMD:SOT-223 | U1 |
| 1 | RST | footprints:SW_SPST_EVQPE1 | SW2 |
Similar boards
- 2 layers100 × 100 mm
- 2 layers85.1 × 31.8 mm
Esp01Expander
ruenahcmohr/esp_01Expand32
esp-01 (esp8266) IO expander, 16 output, 16 input = 32
20 parts15 - 2 layers100.2 × 116.5 mm
- 2 layers212.3 × 100 mm
- 2 layers156.9 × 102.2 mm
HardwareInterfaceBoard
plb500/AutoBloomer-SensorModules
Code and PCB designs for AutoBloomer MQTT sensor modules
85 parts - 2 layers68.6 × 27.9 mm
- 2 layers90 × 110 mm
Questions
How big is the Esp-4digit display PCB?
It measures 50.8 × 19 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Esp-4digit display use?
21 parts, built around the 74HC595 and LM1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Esp-4digit display KiCad files?
From the CRImier/IMTAIDKW repository on GitHub, at the commit this page was made from: the board is hardware/esp-4digit-display.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Esp-4digit display design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).