
Seminraski rad
MartiniGitGub/Upravljanje-ku-anskih-tro-ila-
Upravljanje kućanskim trošilima. Izrada PCB pločice koja obuhvaća sastav kućne automatizacije.

The project involves a digital timer that counts up to one minute. Each counter's 4-bit output is fed into a binary-to-7-segment decoder, enabling number display on 7-segment displays.
DigitalTimer is an open-source printed circuit board by Bican-Valeriu-Cristian, from the Bican-Valeriu-Cristian/DigitalTimer repository on GitHub, published under the MIT licence. It is a 2-layer board of 82 × 84 mm with 38 parts on 83 nets, routed with 371 tracks and 14 vias.
It is built around the 74LS193P-E, HDSP-7403 and L7805, with the NE555D among its other parts. Its parts include 14 resistors, 11 ICs, 4 capacitors, 2 switches and 1 connector.
The project involves a digital timer that counts up to one minute. Each counter's 4-bit output is fed into a binary-to-7-segment decoder, enabling number display on 7-segment displays. The circuit includes switches for starting/stopping the timer and resetting the count.
This circuit diagram represents a digital timer capable of counting seconds up to one minute. The circuit operates by generating a clock signal with a precise frequency of 1 Hz (once per second) using an oscillator based on the NE555 timer. This signal is connected to the count-up input of an integrated circuit counter. Since the counter dedicated to seconds has a 4-bit output, it can count up to 15. Therefore, it requires conditioning with logic circuits to prevent it from exceeding the value of 10. Each time this number is reached, a count-up signal is also sent to a second counter dedicated to tens of seconds. This counter also requires logic conditioning, but this time up to the value of 6.
The 4 bits produced by each counter are then fed into a binary-to-7-segment decoder, which finally allows the numbers to be displayed on 7-segment displays. Additionally, the circuit includes two switches, one for starting and stopping the timer and another for resetting the count.
| File/folder | Description |
|---|---|
PCB.kicad_sch | Schematic |
PCB.kicad_pcb | PCB editor |
gerber | Altium Designer schematics, PCB layout, and supporting project files |
README.md | This README file. |
LICENSE | The license for the project. |
First step:
The schematic for this project was created using KiCad software.
Next was drawing the layout:
-The PCB is a 8 cm x 8 cm 2-layer board.
-It has a GND copper plane on both layers.
-All signal traces are 0.254 mm, while the 5V power trace is double the size, at 0.508 mm.
-Proper names were added for the various components, along with description text and a nice drawing.
The final steps were to order the parts, the PCB, and assemble the board.
-The various components were ordered from TME
-The PCB was ordered from Jlcpcb
-2x 7-segment displays
-2x 10nF ceramic capacitors
-1x 1uF electrolytic capacitor
-2x push switches
-2x header pins
-2x 4-bit tri-state registers
-2x 4-bit BCD decoders
-2x 4-bit counters
-2x quad AND gate chips
-1x quad NOR gate chip
-1x dual JK flip-flop chip
-Various resistors
For details on license, see LICENSE in this directory.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 300R | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R11, R12, R13, R14 |
| 2 | 100n | Capacitor_THT:C_Disc_D3.0mm_W2.0mm_P2.50mm | C1, C2 |
| 2 | 1k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | 1K, 1K |
| 2 | 4511 | Package_DIP:DIP-16_W7.62mm | U6, U10 |
| 2 | 74LS193 | Package_DIP:DIP-16_W7.62mm | U7, U8 |
| 2 | HDSP-7403 | Display_7Segment:HDSP-7401 | U5, U11 |
| 2 | SW_Push | Button_Switch_THT:SW_PUSH_6mm | SW1, SW2 |
| 1 | 10k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | 10K |
| 1 | 10n | Capacitor_THT:C_Rect_L7.0mm_W2.5mm_P5.00mm | C3 |
| 1 | 300 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | 300 |
| 1 | 4071 | Package_DIP:DIP-14_W7.62mm | U4 |
| 1 | 47u | Capacitor_THT:C_Radial_D5.0mm_H11.0mm_P2.00mm | C4 |
| 1 | 74LS08 | Package_DIP:DIP-14_W7.62mm | U3 |
| 1 | 74LS73 | Package_DIP:DIP-14_W7.62mm | U2 |
| 1 | L7805 | Package_TO_SOT_THT:TO-220-3_Vertical | U1 |
| 1 | LOGO | 2.preety:2 | 60s |
| 1 | LOGO | demmo.preety:logodemo | G*** |
| 1 | NE555D | Package_DIP:DIP-8_W7.62mm | U9 |
| 1 | Screw_Terminal_01x02 | TerminalBlock:TerminalBlock_Altech_AK300-2_P5.00mm | J1 |

MartiniGitGub/Upravljanje-ku-anskih-tro-ila-
Upravljanje kućanskim trošilima. Izrada PCB pločice koja obuhvaća sastav kućne automatizacije.

psnogueira/PCB-3Display-7Segmentos
Projeto esquemático e PCB de um circuito controlado por Arduino de 3 displays de 7 segmentos.

RatnakarSahooVSSUT/ESP32-Custom-PCB
Custom ESP32 development board designed in KiCad


yogesh8441/ESP32-CUSTOM-DEVELOPMENT-BOARD
A custom-designed ESP32-WROOM-32D Development Board developed using KiCad 10. This project demonstrates the complete PCB design workflow, including schematic design, PCB layout, routing, ground plane implementation…

codemonkey76/DIY-8-Bit-Computer
DIY 8-Bit Computer, based on the design by Ben Eater


EliMattingly22/Inductor_Saturation_Tester
A circuit to check the saturation level of different inductor cores
It measures 82 × 84 mm and has 2 copper layers, 1.6 mm thick.
38 parts, built around the 74LS193P-E, HDSP-7403, L7805 and NE555D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Bican-Valeriu-Cristian/DigitalTimer repository on GitHub, at the commit this page was made from: the board is PCB.kicad_pcb and its schematic PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).