
Amplifier
BCIT-BAJA/BCIT-BAJA-DAQ
The telemetry system for BCIT-BAJA car, collects strain across suspension components of car to allow BAJA to optimize material and reinforce weak areas of suspension.

The telemetry system for BCIT-BAJA car, collects strain across suspension components of car to allow BAJA to optimize material and reinforce weak areas of suspension.
Hub is an open-source printed circuit board by BCIT-BAJA, from the BCIT-BAJA/BCIT-BAJA-DAQ repository on GitHub. It is a 4-layer board of 99.9 × 99.9 mm with 101 parts on 119 nets, routed with 382 tracks and 118 vias.
It is built around the LMR51606XDBVR-MS, MPU-6500 and CRCW0805100RFKEAC, with the CRCW08051M00FKEAC, F0603G0R02FNTR and BHR-06-VUA among its other parts. Its parts include 25 resistors, 22 capacitors, 18 diodes, 12 connectors and 9 fuses.
During the last BAJA competition,The BAJA team was unable to measure dynamic forces applied onto the suspension of the car. As a result, during the last competition, it bent.
The telemetry system for BCIT-BAJA car, collects strain across suspension components of car to allow BAJA to optimize material and reinforce weak areas of suspension. As well as collect other data such as linear/angular acceleration.
There consists of 2 parts of this project.
PART B the amplification of the (-15-15mV) analog strain signal to (0-3.0V) which is then routed to
PART A, which collects the 8 conditioned analog signals and is transmitted/received over a 915MHz antenna
Power supply circuitry
Conditioning of analog signals
Additional peripherals used
Example of LTSPICE simulation used for amplifier board + signal conditioning
Verified amplifier board working
| Qty | Value | Footprint | References |
|---|---|---|---|
| 18 | D_Zener_Small | Diode_SMD:D_SOD-123 | D1, D2, D3, D4, D5, D6, D7, D10, D11, D12, D13, D14, D15, D16, D17, D18 +2 |
| 9 | 6.8nF ±10% | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C6, C8, C9, C11, C13, C15, C16, C17, C18 |
| 8 | 100 ±1% | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R11, R13, R15, R17, R19, R21, R23 |
| 8 | 1M ±1% | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R12, R14, R16, R18, R20, R22, R24, R26 |
| 8 | 70mA 5s Fusing, 7.5 Ohms | Fuse:Fuse_0603_1608Metric_Pad1.05x0.95mm_HandSolder | F2, F3, F4, F5, F6, F7, F8, F9 |
| 8 | IDC 6Pin Male Header | Lib:AdamTech_BHR-06-VUA | J6, J7, J8, J9, J10, J11, J12, J13 |
| 6 | 10K ±1% | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R6, R7, R8, R9, R25 |
| 5 | 22uF ±10% | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C20, C21, C22, C24 |
| 4 | 0.1uF ±10%, X7R | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C7, C10, C14 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | TestPoint | TestPoint:TestPoint_Pad_D1.5mm | TP1, TP2, TP4 |
| 2 | 1uF, X7R | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C4 |
| 2 | LOGO | Lib:BCIT-Racing-Logo_20mm_8mm8 | G***, G*** |
| 1 | 0 | Lib:ZeroOhmSwitch_R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 10K +-1%, ±100ppm/°C | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 1 | 10nF ±10%, Ceramic, X7R, >4V | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C12 |
| 1 | 10uF, X7R | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C5 |
| 1 | 150uH | Lib:LQH44PH151MPRL_IND_LQH44PN_PR_MUR-M | L1 |
| 1 | 76.8K+- 1%, ±100ppm/°C | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
| 1 | Adafruit 3070 | Lib:Adafruit3070 | U4 |
| 1 | Conn_01x04 | Lib:Battery_PinHeader_1x04_P2.54mm_Vertical | J20 |
| 1 | Conn_01x04 | Lib:BatterySwitch_PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | Conn_01x05 | Lib:SPIExtra_PinHeader_1x05_P2.54mm_Vertical | J4 |
| 1 | Conn_01x05 | Lib:GND_PinHeader_1x05_P2.54mm_Vertical | J5 |
| 1 | FAST-BLOW 375mA 32V 0.45Ω | Fuse:Fuse_0603_1608Metric_Pad1.05x0.95mm_HandSolder | F1 |
| 1 | LMR51603XFDBVR | Lib:LMR51603XFDBVR_DBV0006A-MFG-IPC_C | U2 |
| 1 | MPU-6500 | Lib:MPU-6500_QFN40P300X300X95-25N | U3 |
| 1 | NUCLEO-L476RG | Lib:MODULE_NUCLEO-L476RG | U1 |
| 1 | PMOS | Package_TO_SOT_SMD:TSOT-23 | Q3 |

BCIT-BAJA/BCIT-BAJA-DAQ
The telemetry system for BCIT-BAJA car, collects strain across suspension components of car to allow BAJA to optimize material and reinforce weak areas of suspension.

NOAA-PMEL/ASVCO2
Open Source Repository for the Autonomous Surface Vehicle CO2 (ASVCO2) gen2 system




AxelMcKenna/AFX-1000
RMX-1000-inspired effects processor for macOS, AU and VST3, built on a shared C++20 engine. Standalone Daisy Seed 3 hardware with two main PCBs and a custom housing is in development.



JitterCompany/debug-tools
Collection of useful utility PCBs for development purposes
It measures 99.9 × 99.9 mm and has 4 copper layers, 1.55 mm thick.
101 parts, built around the LMR51606XDBVR-MS, MPU-6500, CRCW0805100RFKEAC and CRCW08051M00FKEAC. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the BCIT-BAJA/BCIT-BAJA-DAQ repository on GitHub, at the commit this page was made from: the board is Revision01/Hardware/Hub/Hub.kicad_pcb and its schematic Revision01/Hardware/Amplifier/Amplifier.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask BCIT-BAJA before reusing the design.