

Chronos polaris hardware
A flight computer designed during my freshman year in university for my Rocketry Organization
- Size
- 30 × 50 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 61
- Nets
- 70
- Pads
- 278
- Tracks, vias
- 544, 113
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 3 Sep 2026
- Updated
- 3 Oct 2026
Overview
Chronos polaris hardware is an open-source printed circuit board by Anish-Agarwall, from the Anish-Agarwall/Polaris-Flight-Computer repository on GitHub. It is a 2-layer board of 30 × 50 mm with 61 parts on 70 nets, routed with 544 tracks and 113 vias.
It is built around the ESP32-S2-SOLO-2-N4, BMP280 and TLV62130RGTR, with the AP20P30Q, BMI088 and FC-B1010RGBT-HG among its other parts. Its parts include 23 resistors, 12 capacitors, 12 ICs, 9 connectors and 2 inductors. It belongs with the ESP32 boards of this library.
Main components
8ESP32-S2-SOLO-2-N4
SMD-41P-40℃~+85℃ -97dBm 19.5dBm 2.4GHz 310mA 3V~3.6V 71mA ESP32-S2 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD-41P WiFi Modules ROHSEspressif SystemsWiFi ModulesBMP280
LGA-8(2x2.5)-40℃~+85℃ 0.12hpa 1.5pa/K 1.71V~3.6V 1hpa 300nA 30Kpa~1.1bar I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output LGA-8(2x2.5) Pressure Sensors ROHSBoschPressure SensorsTLV62130RGTR
QFN-16-EP(3x3)-40℃~+85℃@(TA) 1 19uA 2.5MHz 3A 3V~17V 900mV~5.5V Adjustable Buck Buck Built-in Yes QFN-16-EP(3x3) DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersAP20P30Q
DFN-8(3x3.3)-55℃~+175℃ 1 P-Channel 1.5V 180pF 18mΩ@4.5V 2.2nF 20A 30V 40W 45nC@10V P-Channel DFN-8(3x3.3) MOSFETs ROHSALLPOWERMOSFETsBMI088
LGA-16(3x4.5)-40℃~+85℃ Accelerometer Gyroscope LGA-16(3x4.5) Accelerometers ROHSBosch SensortecAccelerometersFC-B1010RGBT-HG
SMD-4P,1x1mm-30℃~+85℃ 0.85mm 1.6V~2.4V 120° 12mcd~35mcd 15mcd~55mcd 1mm 1mm 1mm方形灯头 2.2V~3.2V 2.3V~3.2V 24mW 2mA 2mA 32mW 32mW 3mcd~10mcd 460nm~480nm 520nm~545nm 5mA 610nm~630nm Common Anode Top-mount SMD-4P,1x1mm RGB LEDs ROHSFoshan NationStar OptoelectronicsRGB LEDsMSK12C02-HB
SMD,8x2.8mm-25℃~+70℃ 1.4mm 10,000 cycles 12V 2.8mm 50mA 8mm Black Rectangular Columnar SMD(SMT) Tab SPDT Surface Mount, Right Angle SMD,8x2.8mm Slide Switches ROHSSHOU HANSlide SwitchesHNB09A03
插件,D=9mm-20℃~+70℃ 1.5V~4.5V 30mA 3kHz 5.5mm 85dB 9mm Active Buzzer (Built-in Driving Circuit) Electromagnetic 插件,D=9mm Buzzers ROHSJiangsu Huaneng ElecBuzzers
README
README.mdPolaris Flight Computer
An ESP32-S2-based rocket flight computer with onboard sensing, flight-data logging, main and drogue deployment outputs, and two-servo control. This repository includes the Arduino firmware, KiCad hardware design, and an OpenRocket model.
Hardware
| Component | Purpose |
|---|---|
| ESP32-S2-SOLO-2-N4 | Microcontroller module on the custom PCB |
| BMI088 | Accelerometer and gyroscope |
| BMP280 | Pressure, temperature, and barometric altitude |
| microSD card | Flight logs and configuration file |
| Main and drogue circuits | Deployment control and continuity sensing |
| Servo outputs | Two-axis thrust-vector-control code |
| Buzzer | Startup and continuity feedback |
The KiCad PCB uses two copper layers. The firmware uses separate SPI buses for the sensors and SD card. Pin assignments are in src/pinout.h.
Four servo pins are defined, but the current controller attaches two servos. Their center positions, deflection limits, and PWM settings are in src/servo_controller.cpp.
Firmware
The application is written in C++ using the Arduino framework and PlatformIO. It reads the IMU at a nominal rate of about 100 Hz and the barometer at 20 Hz.
The main loop handles:
- Acceleration, angular-rate, pressure, and temperature readings.
- Orientation estimation with the included Fusion library, using the IMU without a magnetometer.
- Launch, post-apogee, and landed-state detection from sensor readings and altitude history.
- Main and drogue deployment triggers based on timers, apogee, or descent altitude.
- Buffered CSV logging to the SD card and serial output.
- Servo deflection calculated from estimated yaw and pitch.
The servo routine is called continuously from the main loop rather than being enabled only after launch. A separate Madgwick implementation is also included, but the active application uses Fusion.
Data logging
Each startup creates a numbered file such as log-0.csv or log-1.csv. The log contains:
- Time in microseconds, pressure, temperature, and altitude.
- Yaw, pitch, roll, acceleration, and angular rate.
- Main and drogue continuity readings.
- Flight state and deployment timestamps.
The code reduces SD writes before launch and after landing, and drains buffered records more frequently during flight. Altitude is referenced to the launch ground level once launch is detected.
The CSV header labels acceleration as m/s², while the BMI088 driver returns values in milli-g. Account for that when analyzing the logs.
Building and uploading
-
Install PlatformIO, either through its editor extension or command-line tools.
-
Open the repository folder containing
platformio.ini. -
Check the board selection and the wiring in
src/pinout.hagainst your hardware. -
Build and upload with:
bash pio run pio run --target upload -
Open the serial monitor at the baud rate used by the firmware:
bash pio device monitor --baud 115200
The checked-in PlatformIO environment is esp32-s2-saola-1, with the Arduino framework and USB CDC enabled. The custom schematic uses an ESP32-S2-SOLO-2-N4 module, so verify the board and upload settings for the assembled PCB.
PlatformIO declares ESP32Servo version ^1.1.3 as a dependency. Fusion is included under lib/Fusion/.
SD configuration
The firmware looks for config.txt in the SD card's root directory. The intended format is one key=value setting per line. Recognized settings include:
| Setting | Purpose |
|---|---|
launch_detection_threshold | Altitude-rise threshold in meters |
launch_detection_min_g | Minimum acceleration threshold in g |
main_timer_ms, drogue_timer_ms | Deployment timers measured from launch |
main_fire_duration_ms, drogue_fire_duration_ms | Output activation durations |
main_altitude_meters, drogue_altitude_meters | Descent deployment altitudes |
main_on_apogee, drogue_on_apogee | Enable deployment at detected apogee |
Defaults are defined near the top of src/main.cpp. No configuration file is included in the repository. The current parser uses fixed substring offsets; check the parsed values through serial output before relying on a configuration file.
Repository layout
| Path | Contents |
|---|---|
src/ | Main application, sensor drivers, pin definitions, buffers, and servo control |
lib/Fusion/ | Orientation-estimation library |
chronos-polaris-hardware/ | KiCad project, schematic, PCB, and STEP model |
chronos-polaris-hardware/JLC2KiCad_lib/ | Custom symbols, footprints, and 3D models |
Polaris Program/Arcturus.ork | OpenRocket model |
platformio.ini | Firmware build configuration |
Opening the hardware
Open chronos-polaris-hardware/chronos-polaris-hardware.kicad_pro in KiCad. The PCB was saved with KiCad 8.0. The project library tables use paths relative to the project directory, so keep the included JLC2KiCad_lib folder alongside the design files.
Open Polaris Program/Arcturus.ork in OpenRocket to inspect the included rocket model.
Parts
61| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 10k | Resistor_SMD:R_0603_1608Metric | R2, R3, R4, R5, R6, R8, R15, R16, R18, R21, R23 |
| 7 | 100nF | Capacitor_SMD:C_0402_1005Metric | C5, C6, C7, C8, C9, C10, C12 |
| 5 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J1, J2, J3, J4, J5 |
| 4 | 30k | Resistor_SMD:R_0603_1608Metric | R7, R14, R17, R22 |
| 2 | 0603WAF5101T5E | polaris-fp:R0603 | R12, R13 |
| 2 | 100k | Resistor_SMD:R_0603_1608Metric | R1, R19 |
| 2 | 10uF | Capacitor_SMD:C_0805_2012Metric | C2, C4 |
| 2 | 22uF | Capacitor_SMD:C_0603_1608Metric | C1, C3 |
| 2 | 51 | Resistor_SMD:R_0603_1608Metric | R9, R10 |
| 2 | AP20P30Q | polaris-fp:DFN-8_L3.3-W3.0-P0.65-LS3.3-BL-EP | U7, U12 |
| 2 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J6, J7 |
| 2 | MountingHole | MountingHole:MountingHole_3.2mm_M3_Pad | H1, H4 |
| 1 | 100 | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 160k | Resistor_SMD:R_0603_1608Metric | R20 |
| 1 | 2.2uH | polaris-fp:IND-SMD_L4.0-W4.0 | L2 |
| 1 | 2.2uH | polaris-fp:IND-SMD_L3.0-W3.0 | L1 |
| 1 | 2N7002KDW_72K | polaris-fp:SOT-363_L2.1-W1.3-P0.65-LS2.3-BL | U8 |
| 1 | 3.3nF | Capacitor_SMD:C_0402_1005Metric | C11 |
| 1 | BMI088 | polaris-fp:LGA-16_L4.5-W3.0-P0.50-BL | U3 |
| 1 | BMP280 | polaris-fp:LGA-8_L2.5-W2.0-P0.65_AMP6127 | U4 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J8 |
| 1 | ESP32-S2-SOLO-2-N4 | polaris-fp:WIRELM-SMD_ESP32-S3-WROOM-1 | U2 |
| 1 | FC-B1010RGBT-HG | polaris-fp:LED-ARRAY-SMD_4P-L1.0-W1.0-TR-RD | U14 |
| 1 | HNB09A03 | polaris-fp:BUZ-TH_BD9.0-P5.00-D0.6-FD | BUZ1 |
| 1 | MSK12C02-HB | polaris-fp:SW-TH_MSK12C02-HB-1 | U10 |
| 1 | TF_PUSH | polaris-fp:TF-SMD_TF-PUSH | U5 |
| 1 | TLV62130RGTR | polaris-fp:QFN-16_L3.0-W3.0-P0.50-TL-EP | U6 |
| 1 | TPS62172DSGR | polaris-fp:WSON-8_L2.0-W2.0-P0.50-TL-EP | U1 |
| 1 | TYPE-C_14PLC-H10_0 | polaris-fp:USB-C-TH_SHOUHAN_TYPE-C-14PLC-H10.0 | U15 |
| 1 | WJ124-3_81-6P | polaris-fp:CONN-TH_6P-P3.81_WJ124-3.81-6P | P1 |
Similar boards
- 4 layers193.2 × 52.8 mm

- 6 layers99.5 × 100 mm

Zynq test
cropinghigh/zynq_a9_mb
Zynq 7z010 dev/main board based on components from Antminer S9 control board
528 parts17 - 2 layers81.2 × 80.9 mm

- 4 layers82 × 100 mm

PCB Kicad
ChristopherAwomolo/Nova-Micromouse
Newer version based off the Futura Micromouse
121 partsMIT - 2 layers45 × 30 mm

- 2 layers26.4 × 62 mm

- 4 layers70 × 80 mm

- 4 layers98 × 121 mm

Questions
How big is the Chronos polaris hardware PCB?
It measures 30 × 50 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Chronos polaris hardware use?
61 parts, built around the ESP32-S2-SOLO-2-N4, BMP280, TLV62130RGTR and AP20P30Q. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Chronos polaris hardware KiCad files?
From the Anish-Agarwall/Polaris-Flight-Computer repository on GitHub, at the commit this page was made from: the board is chronos-polaris-hardware/chronos-polaris-hardware.kicad_pcb and its schematic chronos-polaris-hardware/chronos-polaris-hardware.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Chronos polaris hardware design in my own project?
Its repository states no licence, so its author keeps all rights: ask Anish-Agarwall before reusing the design.