
Fv1 module
niektb/sluisbrinkie-eurorack-published
Published Modules of the Sluisbrinkie project

A PCB Tone Development board for Guitar Effects, built around the SPIN FV1 DSP IC.
SpinV1DevBoard is an open-source printed circuit board by AliceAch, from the AliceAch/SPIN-FV1-Tone-Dev repository on GitHub. It is a 2-layer board with 58 parts on 64 nets, routed with 32 tracks and 0 vias.
It is built around the CH341A, 24LC32A/P and SPN1001. Its parts include 20 capacitors, 17 resistors, 5 ICs, 4 connectors and 2 diodes. It belongs with the audio and music and microcontroller boards boards of this library.
A PCB Tone Development board for Guitar Effects, built around the SPIN FV1 DSP IC. There's not much so far... Look at Docs if you want to look at the project without opening it in KiCad.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10K | Resistor_SMD:R_0805_2012Metric | R9, R10, R12, R13, R16, R17 |
| 6 | 1u | Capacitor_SMD:C_0805_2012Metric | C1, C2, C4, C8, C10, C12 |
| 3 | 0.1u | Capacitor_SMD:C_0805_2012Metric | C6, C7, C14 |
| 3 | 100K | Resistor_SMD:R_0805_2012Metric | R1, R2, R7 |
| 2 | 100R | Resistor_SMD:R_0805_2012Metric | R4, R8 |
| 2 | 1K | Resistor_SMD:R_0805_2012Metric | R3, R11 |
| 2 | 20p | Capacitor_SMD:C_0805_2012Metric | C16, C17 |
| 2 | 47u | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C19, C20 |
| 1 | 100n | Capacitor_SMD:C_0805_2012Metric | C3 |
| 1 | 100u | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C18 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric | C15 |
| 1 | 120p | Capacitor_SMD:C_0805_2012Metric | C9 |
| 1 | 12MHz | FV1:12MHz | Y2 |
| 1 | 15p | Capacitor_SMD:C_0805_2012Metric | C13 |
| 1 | 1M | Resistor_SMD:R_0805_2012Metric | R5 |
| 1 | 1N5817 | Diode_THT:D_DO-41_SOD81_P5.08mm_Vertical_AnodeUp | D2 |
| 1 | 1n | Capacitor_SMD:C_0805_2012Metric | C5 |
| 1 | 22K | Resistor_SMD:R_0805_2012Metric | R6 |
| 1 | 24LC32 | FV1:24LC32 | U4 |
| 1 | 2K2 | Resistor_SMD:R_0805_2012Metric | R14 |
| 1 | 2n2 | Capacitor_SMD:C_0805_2012Metric | C11 |
| 1 | 4K7 | Resistor_SMD:R_0805_2012Metric | R15 |
| 1 | Barrel Jack | FV1:DC-IN-TH_DC-005-5.5-2.0 | DC1 |
| 1 | CH341A | FV1:CH341A | U3 |
| 1 | CTRL1 | FV1:Potentiometer_Modified | B100K3 |
| 1 | CTRL2 | FV1:Potentiometer_Modified | B100K4 |
| 1 | CTRL3 | FV1:Potentiometer_Modified | B100K5 |
| 1 | DT38 | FV1:DT38 | Y1 |
| 1 | GND | Connector_Wire:SolderWire-1.5sqmm_1x01_D1.7mm_OD3.9mm | J3 |
| 1 | IN | Connector_Wire:SolderWire-1.5sqmm_1x01_D1.7mm_OD3.9mm | J1 |
| 1 | J6 | FV1:USB-A-TH_USB-302-T | USB1 |
| 1 | L78L33_SOT89 | Package_TO_SOT_SMD:SOT-89-3 | U5 |
| 1 | LED | LED_THT:LED_D5.0mm | D1 |
| 1 | MIX | FV1:Potentiometer_Modified | B100K1 |
| 1 | OUT | Connector_Wire:SolderWire-1.5sqmm_1x01_D1.7mm_OD3.9mm | J2 |
| 1 | SPN1001 | Package_SO:SOIC-28W_7.5x17.9mm_P1.27mm | U2 |
| 1 | SW | Connector_Wire:SolderWire-1.5sqmm_1x01_D1.7mm_OD3.9mm | J4 |
| 1 | SW_SPDT | FV1:SW-TH_K3-SPDT | SW1 |
| 1 | TL074 | TL074:TL074 | U1 |
| 1 | VOLUME | FV1:Potentiometer_Modified | B100K2 |

niektb/sluisbrinkie-eurorack-published
Published Modules of the Sluisbrinkie project

Upcycle-Electronics/CH341A-Pro
Retrace pics and schematic for the Cheap Black CH341A Serial Flash EEPROM BIOS Programmer

Omarbelh/FlashCore
Hybrid USB-C SPI Flash & EEPROM programmer based on CH341A and ESP32-S3.

ADBeta/CH341A_USB_C
USB-C CH341A Breakout Board with EEPROM, I2C, SPI and UART Outputs - with headers for SOIC Clips

CatspersCoffee/S100-Boards
S-100 bus boards designed and built: Z80 and 80386 CPU cards, SRAM/DRAM memory, CPLD/FPGA I/O and SPI boards, an 18-slot backplane and bus terminator.



58 parts, built around the CH341A, 24LC32A/P and SPN1001. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the AliceAch/SPIN-FV1-Tone-Dev repository on GitHub, at the commit this page was made from: the board is SpinV1DevBoard/SpinV1DevBoard.kicad_pcb and its schematic SpinFV1Dev/SpinV1DevBoard/SpinV1DevBoard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask AliceAch before reusing the design.