Skip to the content
2 layers30 × 53 mmESP32-S3-Development Board, the printed circuit board in 3D

Custom ESP32-S3-WROOM development board designed in KiCad.

Size
30 × 53 mm
Copper layers
2
Thickness
1.6 mm
Parts
28
Nets
73
Pads
216
Tracks, vias
407, 95
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
28 Jul 2026
Updated
28 Jul 2026

Overview

ESP32-S3-Development Board is an open-source printed circuit board by AliKhorasaniEEE, from the AliKhorasaniEEE/ESP32-S3-Development-Board repository on GitHub, published under the MIT licence. It is a 2-layer board of 30 × 53 mm with 28 parts on 73 nets, routed with 407 tracks and 95 vias.

It is built around the ESP32-S3-WROOM-1-N8, AMS1117-3.3 and SRV05-4, with the MMBT2222A among its other parts. Its parts include 8 capacitors, 8 resistors, 4 ICs, 3 connectors and 2 transistors. It belongs with the microcontroller boards boards and the ESP32 boards of this library.

Main components

4

README

README.md

ESP32-S3 Development Board

A custom ESP32-S3-WROOM-1 development board designed in KiCad.

Overview

This project is a two-layer ESP32-S3 development board featuring USB Type-C connectivity, USB-to-UART programming, onboard 3.3 V regulation, and access to all ESP32-S3 GPIO pins.

The board was designed as a learning project to gain practical experience in professional PCB design using KiCad.


Features

  • ESP32-S3-WROOM-1 module
  • USB Type-C connector
  • CP2102N USB-to-UART bridge
  • AMS1117-3.3 V voltage regulator
  • Reset and Boot buttons
  • All 40 ESP32-S3 pins exposed
  • Two-layer PCB
  • Ground plane
  • Decoupling capacitors placed according to the reference design

Main Components

ComponentPart Number
MCUESP32-S3-WROOM-1
USB-UARTCP2102N
Voltage RegulatorAMS1117-3.3
USB ConnectorUSB Type-C 16-Pin

Software

Designed using:

  • KiCad 10.0.4

Repository Structure

Hardware/ KiCad project files

Images/ PCB renders and screenshots


Images

PCB

PCB

Schematic

Schematics

3D View

image

Project Status

Current Revision: A

Prototype

Hardware has not yet been manufactured or electrically validated.


Future Improvements

  • Replace AMS1117 with a low-dropout regulator
  • Improve ground stitching
  • Optimize routing
  • Hardware validation
  • Revision B

References

  • Espressif ESP32-S3 Hardware Design Guidelines
  • Espressif ESP32-S3-WROOM-1 Datasheet
  • CP2102N Datasheet
  • KiCad Official Libraries

License

MIT License

Parts

28
QtyValueFootprintReferences
20.1uFCapacitor_SMD:C_1206_3216MetricC8, C10
210kResistor_SMD:R_0805_2012MetricR7, R8
21uFCapacitor_SMD:C_1206_3216MetricC9, C11
222uFCapacitor_SMD:C_1206_3216MetricC2, C4
25k1Resistor_SMD:R_0805_2012MetricR4, R5
2Conn_01x20_PinConnector_PinHeader_1.00mm:PinHeader_1x20_P1.00mm_VerticalJ2, J3
2MMBT2222APackage_TO_SOT_SMD:SOT-23Q1, Q2
2SW_PushButton_Switch_SMD:SW_Push_SPST_NO_Alps_SKRKSW2, SW3
1100RResistor_SMD:R_0805_2012MetricR3
1100uFCapacitor_SMD:C_1206_3216MetricC5
110KResistor_SMD:R_0805_2012MetricR9
110uFCapacitor_SMD:C_1206_3216MetricC3
11KResistor_SMD:R_0805_2012MetricR10
14K7Resistor_SMD:R_0805_2012MetricR6
1AMS1117-3.3Package_TO_SOT_SMD:SOT-223-3_TabPin2U2
1CP2102N-Axx-xQFN28Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mmU4
1ESP32-S3-WROOM-1RF_Module:ESP32-S3-WROOM-1U1
1LEDLED_SMD:LED_0603_1608MetricD1
1SRV05-4Package_TO_SOT_SMD:SOT-23-6U3
1USB_C_Receptacle_USB2.0_16PConnector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_HorizontalJ1

Similar boards

  • 2 layers85 × 67 mmGaggimate, the printed circuit board in 3D

    Gaggimate

    dulerabbit/GaggiBre-legacy

    This is GaggiBre! a fork of Gaggimate with Manual Brew Control and Adaptive Mode. Made by Dule Rabbit

    113 parts8
  • 2 layers100 × 36 mmSoldering station, the printed circuit board in 3D

    Soldering station

    klaus-liebler/soldering_station

    T12 soldering station pcb kicad

    110 parts
  • 4 layers70.6 × 75 mmSmart irrigator, the printed circuit board in 3D

    Smart irrigator

    mantisea12/esp32_smart_irrigator

    An ESP32 based smart irrigator system that uses a LoRaWAN node to output on LoRa and an ESP32 and solenoid to automatically irrigate when needed.

    33 parts
  • 2 layers156 × 66 mmDash 6.8, the printed circuit board in 3D

    Dash 6.8

    romioRN/Dash6.8-hardware

    wifi name "service", password 12345678, connect to 192.167.4.1

    152 parts11Apache-2.0
  • 4 layers80 × 70 mmCross band handy walkie talkie ES8388, the printed circuit board in 3D

    Cross band handy walkie talkie ES8388

    immortal-sniper1/cross_band_handy_walkie_talkie

    cross band handy walkie talkie. This HT would include 2 SA818s, one for 70cm and one for 2m and could be used for satellite work.

    205 parts6MIT
  • 4 layers340.8 × 104.6 mmNiphar, the printed circuit board in 3D

    Niphar

    mornepousse/Niphargus

    Niphargus — a slim, indestructible wireless split keyboard. ESP32 + nRF24, wired fallback, and an emergency kit hidden behind the USB port. The successor to the Rouge-Gorge.

    287 parts4MIT
  • 4 layers52.6 × 40 mmBioSensorBox, the printed circuit board in 3D

    BioSensorBox

    JH2k00/BioSensorBox

    This repository contains the hardware and software for my project in the Advanced Topics in PCB Design lecture at the Technical University of Darmstadt

    56 parts
  • 2 layers35.6 × 94.6 mmUsb3sun, the printed circuit board in 3D

    Usb3sun

    delan/usb3sun

    usb input adapter for sun workstations

    60 parts45ISC

Questions

How big is the ESP32-S3-Development Board PCB?

It measures 30 × 53 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ESP32-S3-Development Board use?

28 parts, built around the ESP32-S3-WROOM-1-N8, AMS1117-3.3, SRV05-4 and MMBT2222A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ESP32-S3-Development Board KiCad files?

From the AliKhorasaniEEE/ESP32-S3-Development-Board repository on GitHub, at the commit this page was made from: the board is Hardware/ESP32-S3-Development-Board.kicad_pcb and its schematic Hardware/ESP32-S3-Development-Board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the ESP32-S3-Development Board design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).