

Claude Micro
A 13-key agent macropad on clear MX switches: six frosted status keys, seven command keys, a rotary reasoning dial, a planar joystick, a five-pad capacitive touch strip and a 19-LED RGB chain.
- Size
- 159 × 102 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 95
- Nets
- 68
- Pads
- 314
- Tracks, vias
- 624, 131
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 28 Jul 2026
- Updated
- 30 Jul 2026
Overview
Claude Micro is an open-source printed circuit board by Alexpoopy1, from the Alexpoopy1/Claude-Micro repository on GitHub. It is a 2-layer board of 159 × 102 mm with 95 parts on 68 nets, routed with 624 tracks and 131 vias.
It is built around the 74LVC1G17Z, 1N4148W and SK6812MINI-E. Its parts include 33 diodes, 27 capacitors, 13 switches, 10 resistors and 1 IC. It belongs with the keyboards and input boards and the RP2040 boards of this library.
Main components
374LVC1G17Z
SOT-553-40℃~+125℃ 1 1 1.65V~5.5V 10uA 32mA 32mA 4.4ns@5V,15pF 74LVC Push-pull Schmitt trigger Unidirectional SOT-553 Buffers, Drivers, Receivers, Transceivers ROHSDiodes IncorporatedBuffers, Drivers, Receivers, Transceivers1N4148W
SOD-123150mA 1A 1V@50mA 1uA@75V 400mW 4ns 75V Independent SOD-123 Switching Diodes ROHSSTMicroelectronicsSwitching DiodesSK6812MINI-E
SMD-40℃~+85℃ 0.6mA 1.78mm 120mcd~240mcd 120° 160mcd~320mcd 1kHz 2.8mm 2000V 3.2mm 3.7V~5.5V 460nm~470nm 515nm~525nm 620nm~625nm 800Kbit/s 815mcd~1275mcd Semi-transparent lens SMD RGB LEDs(Built-in IC) ROHSOPSCO OptoelectronicsRGB LEDs(Built-In IC)
README
README.mdClaude Micro
A 13-key agent macropad on clear MX switches: six frosted status keys, seven command keys, a rotary reasoning dial, a planar joystick, a five-pad capacitive touch strip and a 19-LED RGB chain. Fully printable, fully routed, fully checked.
Design study of the Work Louder × OpenAI Codex Micro — same feature set (13 switches, 1 encoder, 1 planar joystick, 1 touch sensor, 6 agent keys), rebuilt from scratch as open hardware with the Claude mark on the front.
make # build everything, then verify it
open build/claude-micro.htmlDeploying to Vercel serves the same file: vercel.json runs the STL, PCB and
HTML build steps and publishes build/ as the site, with / rewritten to
claude-micro.html. No framework, no Node build — just the Python tooling
above, so the deployed page is always generated fresh from
config/device.json rather than a stale checked-in copy.
What you get
| Output | Where | What it is |
|---|---|---|
| Interactive viewer | build/claude-micro.html | One self-contained file: WebGL model with an exploded-view slider, PCB layer viewer, schematic, BOM, print guide, firmware reference and the full check report. No network, no CDN. |
| Printable parts | build/stl/*.stl | 9 parts, 22 pieces, ~88 g of filament. Every one proven watertight before it is written. |
| PCB | build/pcb/claude-micro.kicad_pcb | Open in KiCad 7/8. Placed, routed, poured, zoned. Also .kicad_sch, .kicad_pro, .net. |
| EasyEDA schematic | build/pcb/claude-micro-easyeda.json | make easyeda. Opens in EasyEDA (File → Open → EasyEDA) and imports into EasyEDA Pro via File → Import → EasyEDA Standard — for publishing to OSHWLab or ordering through JLCPCB. |
| Fabrication | build/pcb/gerbers/ | RS-274X gerbers for all nine layers plus separate plated and non-plated Excellon drill files. Upload as-is. |
| Assembly | build/pcb/bom.csv, positions.csv | 18 BOM lines, 89 components, pick-and-place positions. |
| Firmware | firmware/qmk/claude_micro/ | Drop-in QMK keyboard folder. |
| Reports | build/pcb/drc_report.json, build/stl_report.json | Machine-readable results of every check. |
Hardware
| Keys | 13 × clear-housing MX switches, 5-pin PCB mount, on a 19.05 mm grid — 6 agent, 7 command |
| Dial | EC11E rotary encoder with push, on a 26 mm knurled knob |
| Joystick | 20 mm 2-axis analog thumbstick into ADC0/ADC1, click on its own pin |
| Touch | 5-pad strip read by RC charge time — no touch controller |
| RGB | 19 × SK6812 (13 per-key + 6 underglow), 5 V through a 74LVC1G17 buffer |
| MCU | RP2040 module, Raspberry Pi Pico form factor (USB-C variant recommended) |
| Board | 159 × 102 mm, 2 layer, 1.6 mm, 0.2 mm rules |
| Case | 165 × 108 × 19.5 mm printed two-piece, 6° tilt feet |
Agent keys
The six frosted keys mirror six host threads. The host pushes state over raw HID and the board renders it:
| State | Colour | |
|---|---|---|
| idle | white | nothing running |
| thinking | blue, breathing | model is reasoning |
| running | light blue, breathing | tools are executing |
| waiting | amber | needs your input |
| done | green | finished cleanly |
| error | red | failed |
If the host goes quiet for 30 s every key falls back to idle, so a crashed bridge never leaves stale status on the desk.
The dial
Turning it walks reasoning effort — low → medium → high → max. Pressing it is an ordinary matrix key (row 3, col 1), so it can be remapped like any other.
How it is built
Everything derives from config/device.json. Change the key pitch there
and the STLs, the board, the firmware descriptors and the viewer all move
together; the test suite fails if any of them disagree.
config/device.json one source of truth
│
tools/ device.py loader + derived layout (LED chain, matrix nodes, pads)
mesh.py watertight mesh kernel (no CSG, no dependencies)
parts.py every physical part, printable and purchased
circuit.py schematic as data: components, footprints, nets
router.py grid maze router + copper pour generator
build_pcb.py place → route → pour → check
outputs.py KiCad, gerbers, Excellon, BOM, board.json
checks.py ERC + DRC + mechanical fit
schematic.py SVG schematic
build_easyeda.py schematic → EasyEDA Standard source
build_stl.py printable parts → binary STL
build_html.py the single-file viewer
build_firmware.py QMK descriptors
tests/ test_all.py 36 checks across geometry, layout, circuit and boardNo third-party packages. Python 3.11 standard library only.
The mesh kernel
There is no CSG. Every solid is built from operations that are watertight by
construction — polygon extrusion, lofting, and lathing — and the awkward case
(capping an outline riddled with holes) is handled by a trapezoidal scanline
decomposition that re-subdivides the side walls so caps and walls share exactly
the same vertices. Mesh.validate() then proves each part is a closed,
consistently oriented 2-manifold with positive volume, and build_stl.py
refuses to write a file that fails.
The router
The board is rasterised onto a 0.2 mm grid where every piece of copper is stamped along with its clearance halo, so "may net N occupy this cell?" is one array lookup. Nets are then routed shortest-first with A* over that grid, with a cost for changing layer and a separate keepout map that stops a via being drilled too close to another hole. Leftover free space becomes the ground pour, emitted as scanline runs. Any GND pad the pour cannot reach gets found by a flood fill and routed in with a track — the same flood fill the DRC uses, so the fixer and the checker cannot drift apart.
Verification
make test runs 36 checks:
- Geometry — kernel invariants, analytic volume checks, a fuzz pass over random hole patterns, and every printable part proven watertight, manifold, correctly oriented, printer-sized and thick enough to print.
- Layout — key pitch, top-surface collisions, bezel window clearances, a monotonic Z stack, and that the encoder shaft does not bottom out in the knob.
- Circuit — ERC, one switch and one diode per matrix node, unique matrix addresses, an unbroken LED chain, no double-booked GPIO, the LED rail fused and level-shifted, the touch strip fully wired.
- Board — every connection routed, ≥ 0.2 mm copper clearance verified on a fresh raster of the finished geometry, annular rings, hole-to-hole spacing, all copper inside the profile, the ground pour reaching every GND pad, no courtyard overlaps, and nothing under the MCU module taller than its standoff.
- Outputs — balanced s-expressions in the KiCad files, well-formed gerbers and Excellon, drill counts matching the board, the BOM covering every component, the viewer free of external references, and the firmware agreeing with the config on pins, LED count, layers and layout size.
- EasyEDA — every shape string matching EasyEDA's documented field order, no duplicate ids, and the connectivity rebuilt out of the exported file the way EasyEDA reads it — pin dot → wire → net label — coming back identical to the source netlist, all 265 pads and 68 nets.
Current status: 0 DRC errors, 0 warnings, 141/141 connections routed, 9/9 meshes watertight.
Building one
- Print at 0.2 mm, 3 walls, 25% infill. No supports on any part. Print the six agent keycaps in natural or clear filament — the roof is 1.0 mm so the status colour reads through. All 13 caps take a standard MX cross stem, so bought keycaps drop straight in if you would rather not print them.
- Order the PCB — upload
build/pcb/gerbers/as a zip. Nothing exotic: 2 layer, 1.6 mm, 0.2 mm track and clearance. - Populate — bottom side first (diodes, 0603s, the SOT-23-5, then the RP2040 module on a 2.54 mm header), then the top: the 19 SK6812s, then the 13 MX switches, the EC11 and the thumbstick. Seat every switch fully — the two locating posts must bottom out before you solder, or the plate will not sit flat.
- Flash —
qmk compile -kb claude_micro -km default, hold BOOTSEL, copy the UF2 across. - Assemble — six M2 heat-set inserts in the bezel, drop the diffuser into the touch window, six M2 × 6 mm screws from underneath.
Full step-by-step with per-part orientation is in the viewer's Print & assemble tab.
Licence
Hardware and firmware are open. The Claude mark is Anthropic's; it is used here on a personal build, not a product for sale.
Parts
95| Qty | Value | Footprint | References |
|---|---|---|---|
| 22 | 100nF | claude-micro:C_0603 | C1, C2, C3, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C24, C25 +6 |
| 14 | 1N4148W | claude-micro:D_SOD123 | D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14 |
| 13 | MX clear | claude-micro:MX_PCB | SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8, SW9, SW10, SW11, SW12, SW13 |
| 13 | SK6812MINI-E | claude-micro:SK6812MINI | LED1, LED2, LED3, LED4, LED5, LED6, LED7, LED8, LED9, LED10, LED11, LED12, LED13 |
| 6 | SK6812-3535 | claude-micro:SK6812_3535 | LED14, LED15, LED16, LED17, LED18, LED19 |
| 5 | 1M | claude-micro:R_0603 | R5, R6, R7, R8, R9 |
| 2 | 10k | claude-micro:R_0603 | R1, R2 |
| 2 | 10nF | claude-micro:C_0603 | C26, C27 |
| 2 | 10uF | claude-micro:C_0805 | C22, C23 |
| 2 | 1k | claude-micro:R_0603 | R3, R4 |
| 1 | 1.1A PPTC | claude-micro:F_1206 | F1 |
| 1 | 2-axis analog thumbstick | claude-micro:Joystick_20mm | JS1 |
| 1 | 470R | claude-micro:R_0603 | R10 |
| 1 | 470uF 10V | claude-micro:C_1210_BULK | C21 |
| 1 | 74LVC1G17 | claude-micro:SOT-23-5 | U2 |
| 1 | EC11E + switch | claude-micro:EC11E | ENC1 |
| 1 | RP2040 Pico-form-factor module | claude-micro:RP2040_Module_Pico | MOD1 |
| 1 | Reset | claude-micro:SW_Push_6mm | SW_RST |
The 89 most common of 95 parts.
Similar boards
- 2 layers304.3 × 108.3 mm

- 2 layers87.2 × 135.7 mm

- 4 layers90.2 × 101.1 mm

- 2 layers90 × 135 mm

- 6 layers46.5 × 47.2 mm

NAVCORE SoOP
kfilipekk/iridium_drone
STM32H743 flight controller that navigates without GPS from Iridium satellite Doppler
217 parts2MIT - 4 layers72.4 × 69.8 mm

- 4 layers101.9 × 84.6 mm

- 4 layers100 × 60 mm

Work after r3
cfbird/usb3-sdr
USB3 direct-sampling HF SDR: AD9649 ADC -> ECP5 FPGA DDC -> FT601 USB 3. KiCad 9 + Verilog, co-designed by Claude and Gemini (AGY).
231 parts
Questions
How big is the Claude Micro PCB?
It measures 159 × 102 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Claude Micro use?
95 parts, built around the 74LVC1G17Z, 1N4148W and SK6812MINI-E. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Claude Micro KiCad files?
From the Alexpoopy1/Claude-Micro repository on GitHub, at the commit this page was made from: the board is build/pcb/claude-micro.kicad_pcb and its schematic build/pcb/claude-micro.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Claude Micro design in my own project?
Its repository states no licence, so its author keeps all rights: ask Alexpoopy1 before reusing the design.