

RobotBalanceador
Robot balanceador de PSM2
- Size
- 70 × 45 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 73
- Nets
- 84
- Pads
- 230
- Tracks, vias
- 412, 60
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 31 Aug 2024
- Updated
- 4 Sep 2024
Overview
RobotBalanceador is an open-source printed circuit board by AlexRuizDiaz, from the AlexRuizDiaz/RobotBalanceador repository on GitHub. It is a 2-layer board of 70 × 45 mm with 73 parts on 84 nets, routed with 412 tracks and 60 vias.
It is built around the DRV8870DDA, LMR62014XMF and AMS1117-3.3, with the MPU-6050 and 1N5819WS among its other parts. Its parts include 24 capacitors, 14 resistors, 7 ICs, 7 connectors and 6 diodes. It belongs with the robots and motor control boards and the STM32 boards of this library.
Main components
5DRV8870DDA
SO-8-40℃~+125℃ 1 3.6A 565mΩ 6.5V~45V 6.5V~45V Bipolar Driver Overcurrent Protection、Short-Circuit Protection、Over temperature protection、Under-voltage lockout、Overvoltage Protection、Built-in charge pump、Power-on reset、Dead-time / shoot-through protection Yes SO-8 Stepper Motor Driver ROHSTexas InstrumentsStepper Motor DriverLMR62014XMF
SOT-23-5-40℃~+125℃@(TJ) 1 1.6MHz 2.7V~14V 2A 3V~20V 400uA Adjustable Boost Boost Built-in No SOT-23-5 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMPU-6050
QFN-24-EP(4x4)-40℃~+85℃ 16bit 1KB 2.375V~3.46V 5uA Accelerometer Gyroscope I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(4x4) Accelerometers ROHSTDK InvenSenseAccelerometers1N5819WS
SOD-3231 Independent 1A 25A 40V 500uA@40V 600mV@1A SOD-323 Schottky Diodes ROHSGuangdong HottechSchottky Diodes
README
README.mdRobot balanceador de PSM2 Requisitos:
- Kicad 8.0.4 o mayor
- STM32CubeIDE 1.14.0 o mayor
Parts
73| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100n | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C4, C5, C8, C18, C20, C21, C24 |
| 5 | 10k | Resistor_SMD:R_0603_1608Metric | R1, R3, R4, R5, R8 |
| 5 | 10u | Capacitor_SMD:C_0603_1608Metric | C9, C12, C13, C15, C17 |
| 5 | 1N5819WS | Diode_SMD:D_SOD-323 | D1, D2, D3, D4, D5 |
| 4 | 1.5k | Resistor_SMD:R_0603_1608Metric | R11, R15, R16, R17 |
| 2 | 100m | Resistor_SMD:R_1206_3216Metric | R9, R10 |
| 2 | 10u | Inductor_SMD:L_1008_2520Metric | L1, L2 |
| 2 | 22u | Capacitor_SMD:C_0805_2012Metric | C10, C11 |
| 2 | 30p | Capacitor_SMD:C_0603_1608Metric | C6, C7 |
| 2 | 330p | Capacitor_SMD:C_0603_1608Metric | C14, C16 |
| 2 | 47u | Capacitor_SMD:CP_Elec_6.3x5.4 | C22, C23 |
| 2 | 82k | Resistor_SMD:R_0603_1608Metric | R2, R7 |
| 2 | DRV8870DDA | Package_SO:Texas_HTSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.95x4.9mm_Mask2.4x3.1mm_ThermalVias | U6, U7 |
| 2 | ENCODER | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J4, J5 |
| 2 | LMR62014XMF | Package_TO_SOT_SMD:SOT-23-5 | U2, U4 |
| 1 | 2.2n | Capacitor_SMD:C_0603_1608Metric | C19 |
| 1 | 27k | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 8MHz | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Y1 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | Barrel_Jack_Switch | Connector_BarrelJack:BarrelJack_GCT_DCJ200-10-A_Horizontal | J3 |
| 1 | G*** | kibuzzard-66D67A51 | kibuzzard-66D67A51 |
| 1 | G*** | kibuzzard-66D679FF | kibuzzard-66D679FF |
| 1 | G*** | kibuzzard-66D67A08 | kibuzzard-66D67A08 |
| 1 | G*** | kibuzzard-66D679EB | kibuzzard-66D679EB |
| 1 | G*** | kibuzzard-66D67EE6 | kibuzzard-66D67EE6 |
| 1 | G*** | kibuzzard-66D67A48 | kibuzzard-66D67A48 |
| 1 | G*** | kibuzzard-66D67F1F | kibuzzard-66D67F1F |
| 1 | G*** | kibuzzard-66D67A11 | kibuzzard-66D67A11 |
| 1 | G*** | kibuzzard-66D67A84 | kibuzzard-66D67A84 |
| 1 | G*** | kibuzzard-66D679E8 | kibuzzard-66D679E8 |
| 1 | G*** | kibuzzard-66D67A2F | kibuzzard-66D67A2F |
| 1 | G*** | kibuzzard-66D679E5 | kibuzzard-66D679E5 |
| 1 | ICSP | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | MOT 1 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J6 |
| 1 | MOT 2 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J7 |
| 1 | MPU-6050 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | U5 |
| 1 | RED | LED_SMD:LED_0603_1608Metric | D6 |
| 1 | STM32F103C8Tx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Molex_47346-0001 | J2 |
Similar boards
- 2 layers56.6 × 25 mm

- 2 layers43.5 × 46.9 mm

Schaltplan Ultraschallsensor
Tinkerforge/distance-us-v2-bricklet-techniker
This repository contains the firmware source code and the hardware design files. The documentation generator configs can be found at https://github.com/Tinkerforge/generators
54 parts2 - 2 layers30 × 97 mm

Helix vape
stevensun369/helix-vape-pcb
KiCad design for an ESP32-C6 buck-boost vape mod power board — LM5175 stage, 1.0–10 V @ 80 W, with full JLCPCB production files.
83 parts1 - 4 layers75 × 60 mm

- 4 layers35 × 34 mm

- 2 layers49.5 × 38.1 mm

Tinkerforge distance us v2 bricklet techniker ultraschallsensor
oomlout/oomlout_oomp_project_bot_v_2
64 parts - 2 layers96.6 × 100 mm

- 4 layers69.5 × 62.6 mm

Questions
How big is the RobotBalanceador PCB?
It measures 70 × 45 mm and has 2 copper layers, 1.6 mm thick.
What parts does the RobotBalanceador use?
73 parts, built around the DRV8870DDA, LMR62014XMF, AMS1117-3.3 and MPU-6050. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the RobotBalanceador KiCad files?
From the AlexRuizDiaz/RobotBalanceador repository on GitHub, at the commit this page was made from: the board is Circuito/RobotBalanceador/RobotBalanceador.kicad_pcb and its schematic Circuito/RobotBalanceador/RobotBalanceador.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the RobotBalanceador design in my own project?
Its repository states no licence, so its author keeps all rights: ask AlexRuizDiaz before reusing the design.