
Elektor
joseluu/Elektor_sdr_teensy
Sdr hardware front end shield to be used on top of the teensy audio board

PS/2 keyboard interface for the Atari 2600 and 7800
Keyboard-2600 is an open-source printed circuit board by Al-Nafuur, from the Al-Nafuur/KeyPortari repository on GitHub, published under the MIT licence. It is a 2-layer board of 80 × 59.7 mm with 31 parts on 51 nets, routed with 646 tracks and 43 vias.
It is built around the ATMEGA328P-AU and 74HC4066D,653-JSM. Its parts include 7 connectors, 6 resistors, 5 capacitors, 3 ICs and 2 switches. It belongs with the keyboards and input and retro computing and games boards and the AVR (ATmega, ATtiny) boards of this library.
This project enables the connection of a PS/2 keyboard (or a USB keyboard that supports the PS/2 protocol) to the Atari 2600 or 7800 console. The ATmega328P processes keystrokes and controls the joystick inputs of the Atari 2600 accordingly. When no keyboard is needed, the KeyPortari also transparently forwards a real joystick, paddle, or other controller straight through to the console.
The easiest way to flash or update the firmware is the KeyPortari Web Updater — flashes directly from your browser (Chrome, Edge, or Firefox 151+) via the Web Serial API, no Arduino IDE or driver installation required. Source: KeyPortari-Updater.
Alternatively, upload Keyboard-26.ino the classic way via the Arduino IDE or AVRDUDE.
The DIP switch block configures both the active protocol and the keyboard layout. Down = On = 1, Up = Off = 0.
⚠️ Changed in firmware v1.2.0: the DIP switch assignment is different from older firmware versions, so settings from an older firmware do not carry over. Layout is now selected by DIP 1 only (the French layout was removed), and the protocol by DIP 2–4 (previously DIP 3+4). An old setting can now select a different protocol, so re-check your switches after updating.
Keyboard layout (DIP 1):
| Pos 1 | Layout |
|---|---|
| 0 | US |
| 1 | DE |
Protocol (DIP 2–4):
| Pos 2 | Pos 3 | Pos 4 | Protocol |
|---|---|---|---|
| 0 | 0 | 0 | None (port forwarding only) |
| 1 | 0 | 0 | 24Char display (port forwarding active while no key is pressed) |
| 0 | 1 | 0 | Basic Programming (port forwarding disabled, requires jumpers set — see warning below) |
| 1 | 1 | 0 | CompuMate (port forwarding disabled, requires jumpers set — see warning below) |
| 0 | 0 | 1 | Atari 7800 Keyboard (port forwarding disabled) |
| 1 | 0 | 1 | 7-bit ASCII (port forwarding active while no key is pressed) |
| 0 | 1 | 1 | unused — behaves like None (port forwarding only) |
| 1 | 1 | 1 | unused — behaves like None (port forwarding only) |
After changing DIP switches, press the Reset button on the KeyPortari to apply the new configuration — this works at runtime, no need to power-cycle the Atari.
(photo placeholder: DIP switch block)
Flash the firmware — see Flashing the Firmware above.
Connect PS/2 keyboard to the corresponding pins.
Set DIP switches for the desired configuration (see table above).
Connect to the Atari 2600 joystick port — the cables connecting to the 2600 joystick ports should point outwards from the KeyPortari.
(photo placeholder: joystick cable orientation)
These two protocols need extra wiring: the TIA's INPT0–INPT5 lines must be manually routed to ATmega GPIOs A0–A3, PB2, and PB3 (MOSI) using the 6 included jumper wires via the expansion port pin header.
(photo placeholder: expansion port jumper wiring)
⚠️ Electrical caution: The included jumpers have no built-in series resistors. If a joystick, paddle, or keypad is connected to the same TIA inputs at the same time as the jumpers, this causes signal contention that can permanently damage the ATmega's GPIOs (the TIA inputs themselves are not at risk).
Never use joysticks, paddles, or other controllers on the KeyPortari forwarding ports while a Basic Programming or CompuMate protocol jumper is connected. Best practice: leave the protocol DIP switches at None (DIP 2–4 all OFF,
0-0-0) by default, and only switch to the specific protocol right before launching that ROM, then press the KeyPortari's Reset button. Optionally, add external ~220Ω series resistors between the TIA inputs and the ATmega GPIOs for extra protection (planned as standard on future expansion boards).
Protocol compatibility:
Shift, Ctrl, and Alt influence the key output (e.g., uppercase/lowercase characters).A step-by-step checklist for testing a KeyPortari, from basic hardware to full keyboard functionality, is maintained in the AtariAge docs thread. Short version:
Level 1 — Basic hardware + port forwarding (no keyboard):
0-0-0 (None), power via the Atari.Level 2 — Basic keyboard functionality:
1-0-0 (24Char display), connect a PS/2 keyboard, power on — check for NumLock/CapsLock LED activity as a power sanity check./Public ROMs/Homebrew/Hardware/KeyPortari/24Char Notepad xxxx.bin) and confirm layout, modifier keys, and responsiveness.
None currently open — please file an issue if you run into something.
Fixed in v1.2.1: with firmware v1.2.0, the two unused protocol DIP combinations (DIP 2–4 = 0-1-1 and 1-1-1) read past the end of the protocol table, which could hang the KeyPortari. They now behave like None. If you are on v1.2.0, please update.
PCB manufacturing for this project was kindly sponsored by JLCPCB – a leading PCB prototype service. For the first prototype run, JLCPCB generously provided 15 SMD assembled test boards, helping to accelerate early hardware development.
If you’re a developer or hardware tinkerer and would like to experiment with the interface or contribute your own ideas, feel free to reach out to me via AtariAge – I’d be happy to provide a board to support your work.
If you have any questions or suggestions, feel free to open an issue on GitHub! 🎮
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole | MountingHole:MountingHole_3mm | H1, H2, H3, H4 |
| 3 | 0.1 uF | Capacitor_SMD:C_0402_1005Metric | C2, C4, C5 |
| 2 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C1, C3 |
| 2 | 10K | Resistor_SMD:R_0402_1005Metric | R1, R3 |
| 2 | 74HC4066D_653 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U2, U3 |
| 1 | 100K | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 16Mhz | Crystal:Resonator_SMD_Murata_CSTxExxV-3Pin_3.0x1.1mm | Y2 |
| 1 | 20K | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 40K | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 80K | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | ATmega328P-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U1 |
| 1 | Config Switch-Box | Button_Switch_THT:SW_DIP_SPSTx04_Piano_10.8x11.72mm_W7.62mm_P2.54mm | SW1 |
| 1 | Expansion Port | KeyPortari:PinHeader_2x14_P2.54mm_Vertical_KeyPortari_Expansion-Port | J6 |
| 1 | FTDI Basic | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Horizontal | JP1 |
| 1 | Joystick left | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical | J8 |
| 1 | Joystick right | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical | J7 |
| 1 | LOGO | KeyPortari:Logo KeyPortari | G*** |
| 1 | Left Forward Port | Connector_Dsub:DSUB-9_Male_Horizontal_P2.77x2.84mm_EdgePinOffset4.94mm_Housed_MountingHolesOffset7.48mm | J2 |
| 1 | Mini-DIN-6 | KeyPortari:Connector_Mini-DIN_Female_6Pin_2rows | J5 |
| 1 | Reset | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KMR2 | SW2 |
| 1 | Right Forward Port | Connector_Dsub:DSUB-9_Male_Horizontal_P2.77x2.84mm_EdgePinOffset4.94mm_Housed_MountingHolesOffset7.48mm | J3 |
| 1 | USB_A | Connector_USB:USB_A_Molex_67643_Horizontal | J1 |
The 30 most common of 31 parts.

joseluu/Elektor_sdr_teensy
Sdr hardware front end shield to be used on top of the teensy audio board

dmcke5/NucDeck
The Open Source DIY Handheld Gaming PC!


profdc9/RFBitBanger
A QRP digital transceiver created from readily available parts for off-the-grid maintenance

futureshocked/KLP4e_MCU-Datalogger
This is the repository for the "MCU Datalogger" project.


sportiduino/sportiduino
Electronic timing system for orienteering and similar outdoor sports events on Arduino

SukkoPera/OpenPSX2AmigaPadAdapter
Playstation to Commodore Amiga/CD32 Controller Adapter
It measures 80 × 59.7 mm and has 2 copper layers, 1.6 mm thick.
31 parts, built around the ATMEGA328P-AU and 74HC4066D,653-JSM. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Al-Nafuur/KeyPortari repository on GitHub, at the commit this page was made from: the board is pcb/Keyboard-2600/Keyboard-2600.kicad_pcb and its schematic pcb/Keyboard-2600/Keyboard-2600.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).