

Controller a r1
New public repo for work on LED Glasses
- Size
- 131.2 × 17.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 15
- Nets
- 35
- Pads
- 72
- Tracks, vias
- 118, 27
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 12 Oct 2019
- Updated
- 9 Apr 2024
Overview
Controller a r1 is an open-source printed circuit board by 4lml4, from the 4lml4/LED_Glasses repository on GitHub. It is a 2-layer board of 131.2 × 17.5 mm with 15 parts on 35 nets, routed with 118 tracks and 27 vias.
It is built around the STM32G071KBU6, MIC5504-3.3YM5 and MBR0520LT1G, with the SPH0641LM4H-1 among its other parts. Its parts include 6 capacitors, 2 ICs, 2 connectors, 2 switches and 1 resistor. It belongs with the STM32 boards of this library.
Main components
4STM32G071KBU6
UFQFPN-32(5x5)-40℃~+85℃ 1.71V~3.6V 128KB 12bit 12bit 30 32 Bit 36KB 64MHz ARM Cortex-M0+ Built-in+External FLASH UFQFPN-32(5x5) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)MIC5504-3.3YM5
SOT-23-5-40℃~+125℃@(Tj) 1 120uVrms 15uA 180mV@(300mA) 3.3V 300mA 5.5V 75dB@(1kHz) Fixed Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMBR0520LT1G
UncategorisedUnknown makerSPH0641LM4H-1
LGA-5(3.5x2.7)-26dB 0.98mm 1.8V 2.65mm 235uA、620uA 3.5mm 64dB、64.3dB Differential output Omnidirectional Omnidirectional pickup LGA-5(3.5x2.7) MEMS Microphones ROHSKnowlesMEMS Microphones
README
README.mdLED_Glasses
A hobby project aimed at making sound reactive LED glasses that you should take clubbing.
Hardware
The hardware consists entirely of three PCBs without an enclosure with low profile hinges and a battery system that has yet to be worked out. The PCBs are designed in KiCAD and are as follows:
- The controller arm (
hardware/arm_mcu) which houses the microcontroller (STM32G071KBU6), a microphone (SPH0641LM4H-1) and a 3v3 linear regulator. - The power arm (
hardware/arm_power) which houses input power protection, an on switch, 5v5 switching regulator and a power good indicator. - The front display (
hardware/front_display) which houses the LED matrix (SK6812MINI).
Firmware
firmware/arduino contains an early revision of the firmware, with heavy modifications likely in future versions.
Hardware abstraction will be provided by either the STM HAL (pretty bloated and not very intuitive), STM LL (not very intuitive and a bit difficult to parse the many thousand line header files for insight), libopencm3 (haven't tried it but I've heard it's pretty good) or CMSIS (gives us the most control but literally no help haha) (i.e. we haven't decided yet but probably not Arduino).
TODO
- Read https://github.com/EdwardHartmann/SK6812RGBW for inspiration
- Decide on copyright license
- Investigate smaller LED packages
Parts
15| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100n, 25V | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C103, C104, C105, C106 |
| 2 | 4u7, 25V | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C101, C102 |
| 2 | Push Button | Button_Switch_SMD:SW_SPST_CK_KXT3 | SW101, SW102 |
| 1 | 100k, 1/16W | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R101 |
| 1 | Front Connector | rave_shades:PinHeader_1x03_P1.00mm_Vertical_SMD_Pin1Left_CUSTOM | J101 |
| 1 | MBR0520LT1G | Diode_SMD:D_SOD-123 | D101 |
| 1 | MIC5504-3.3YM5 | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U101 |
| 1 | SPH0641LM4H-1 | rave_shades:MIC_SPH0641LM4H-1 | MK101 |
| 1 | STM32G071KBU6 | rave_shades:QFN50P500X500X60-33N-D | U102 |
| 1 | SWD | rave_shades:PinHeader_1x05_P1.00mm_Vertical_SMD_Pin1Left_CUSTOM | J102 |
More from 4lml4/LED_Glasses
6- 4 layers155 × 54.5 mm

- 2 layers152.9 × 54.6 mm

- 4 layers131.5 × 13 mm

- 4 layers131.5 × 13 mm

- 2 layers130.8 × 20.4 mm

- 2 layers70 × 80 mm

Similar boards
- 8 layers35.5 × 62.5 mm

- 2 layers8.6 × 5 mm

- 2 layers77.6 × 116.3 mm

- 4 layers76 × 72 mm

Keychain rev b panel
olerast67/emotion-keychain
Брелок с OLED-экраном и анимированными эмоциями
168 partsApache-2.0 - 2 layers

SkyRizz ESPSOL
SkyRizzAI/SkyRizz-ESPSOL
An open-hardware, coin-sized ESP32-S3 development board with an on-board secure element, 6-axis IMU, PDM microphone, buzzer, USB-C, and Li-Po charging — all on a 40.6 mm (1.6") round, 2-layer PCB.
101 partsCERN-OHL-S-2.0 - 4 layers118 × 76 mm

Smart led badge
zgeez/Pixel-Badge
Wearable 32x32 LED badge with Zephyr firmware, BLE control, passive NFC, and a Flutter Android app, built around a custom nRF52840 PCB.
1,236 partsMIT - 2 layers47 × 27.6 mm

- 4 layers58.4 × 22.9 mm

Quickfeather board
QuickLogic-Corp/quick-feather-dev-board
100% open source dev kit for EOS S3 MCU+eFPGA SoC supported by fully open source SDK and FPGA Toolchain
101 parts66CC-BY-SA-4.0
Questions
How big is the Controller a r1 PCB?
It measures 131.2 × 17.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Controller a r1 use?
15 parts, built around the STM32G071KBU6, MIC5504-3.3YM5, MBR0520LT1G and SPH0641LM4H-1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Controller a r1 KiCad files?
From the 4lml4/LED_Glasses repository on GitHub, at the commit this page was made from: the board is hardware/controller_a_r1/controller_a_r1.kicad_pcb and its schematic hardware/controller_a_r1/controller_a_r1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Controller a r1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask 4lml4 before reusing the design.