Skip to the content
25262728

SIC437BED

Vishay IntertechnologyExtended

-40℃~+125℃@(TJ) 1 12A 300kHz~1MHz 3V~28V 50uA 600mV~20V Adjustable Buck Buck Built-in Yes PowerPAK-MLP44-24L DC-DC Converters ROHS

Part id
vishay/SIC437BED
Category
DC DC Converters
Package
PowerPAK-MLP44-24L
Pins
28
In stock
412 at JLCPCB (C2685654)
Used on
4 open-source boards

Overview

The SIC437BED is a DC DC Converter made by Vishay Intertechnology in a PowerPAK-MLP44-24L package with 28 pins. -40℃~+125℃@(TJ) 1 12A 300kHz~1MHz 3V~28V 50uA 600mV~20V Adjustable Buck Buck Built-in Yes PowerPAK-MLP44-24L DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (Regulator_Switching:SIC437B, from KiCad's library) and its footprint (Package_DFN_QFN:Vishay_PowerPAK_MLP44-24L, from KiCad's library), ready for a KiCad board. 412 are in stock at JLCPCB (part C2685654). 4 open-source boards in 3 repositories on GitHub use it.

Symbol

1VIN3PGND5SW10GL12VDRV14PGOOD15VDD16AGND17FB18VOUT19EN20MODE221MODE123BOOT24PHASE
Regulator_Switching:SIC437BFrom KiCad's library

Footprint

25262728
Package_DFN_QFN:Vishay_PowerPAK_MLP44-24LFrom KiCad's library

From the datasheet

13
Supply, least
4.5 V · VIN, recommended operating min, SiC43xB · p. 3
Supply, most
28 V · VIN, recommended operating max, SiC43xB · p. 3
Supply, absolute maximum
30 V · VIN, absolute max relative to PGND · p. 3
Supply, absolute maximum
6 V · VDD / VDRV, absolute max relative to PGND · p. 3
Works from
-40 °C · recommended ambient temperature min · p. 3
Works up to
105 °C · recommended ambient temperature max · p. 3
Junction, hottest
150 °C · absolute max junction temperature · p. 3
Takes working
50 µA · typical input current, non-switching, VFB > 0.6 V · p. 4
Takes asleep
500 nA · typical shutdown current, VEN = 0 V · p. 4
Gives
12 A · rated continuous output current, SiC437 · p. 1
Feedback reference
600 mV · typical internal feedback reference voltage · p. 6
Junction to air (PowerPAK® MLP44-24L)
16 K/W · junction to ambient thermal impedance rating · p. 3
Junction to case (PowerPAK® MLP44-24L)
2 K/W · junction to case thermal impedance rating · p. 3

What it is and has

12
Topology
Synchronous buck regulator with integrated high side and low side power MOSFETs · p. 1
Output voltage
Adjustable down to 0.6 V · p. 1
Output voltage accuracy
± 1 % at -40 °C to +125 °C · p. 1
Peak efficiency
97 % · p. 1
Switching frequency
Programmable: 300 kHz, 500 kHz, 750 kHz, 1 MHz · p. 1
Soft start and current limit
Adjustable · p. 1
Overcurrent protection
Cycle-by-cycle current limit · p. 1
Overvoltage protection
Output overvoltage protection · p. 1
Power good and thermal protection
Power good flag and over temperature protection · p. 1
Package
MLP44-24L · p. 6
Output voltage adjustment
Adjustable down to 0.6 V · p. 1
Output voltage accuracy
± 1 % · p. 1

Around it

2
cap 2.2 μF
between VDRV and PGND; Internal gate driver supply decoupling. · p. 2
cap 1 μF
between VDD and AGND; Internal logic supply decoupling. · p. 2

Specifications

58
ParameterConditionsAs printedPage
VIN VINReference to PGNDmin -0.3 · max 30 V3
VOUT VOUTReference to PGNDmin -0.3 · max 22 V3
VDD / VDRVReference to PGNDmin -0.3 · max 6 V3
SW / PHASEReference to PGNDmin -0.3 · max 30 V3
SW / PHASE (AC)100 ns; reference to PGNDmin -8 · max 35 V3
BOOT BOOTReference to PGNDmin -0.3 · max 6 V3
BOOT to SWmin -0.3 · max 6 V3
AGND to PGNDmin -0.3 · max 0.3 V3
EN ENReference to AGNDmin -0.3 · max 30 V3
All other pinsReference to AGNDmin -0.3 · max 6 V3
Junction temperature TJmin -40 · max 150 °C3
Storage temperature TSTGmin -65 · max 150 °C3
Junction to ambient thermal impedance (RJA) RJAPowerPAK® MLP44-24Lmax 16 °C/W3
Junction to case thermal impedance (RJC) RJCPowerPAK® MLP44-24Lmax 2 °C/W3
Maximum power dissipationAmbient temperature = 25 °Cmax 7.75 W3
Electrostatic discharge protectionHuman body modelmax 4000 V3
Electrostatic discharge protectionCharged device modelmax 1000 V3
Input voltage (VIN) (SiC43xA, SiC43xB) VINSiC43xBmin 4.5 · max 28 V3
Enable (EN) ENmin 0 · max 28 V3
Input voltage (VIN), external supply on VDD / VDRV VINexternal supply on VDD / VDRVmin 3 · max 28 V3
Output voltage (VOUT) VOUTMaximum: 0.9 x VIN and < 20 Vmin 0.6 V3
Recommended ambient temperaturemin -40 · max 105 °C3
Operating junction temperaturemin -40 · max 125 °C3
VDD supply VDDVIN = 6 V to 28 V; SiC43xB; VEN = 5 V; TJ = -40 °C to +125 °Cmin 4.75 · typ 5 · max 5.25 V4
VDD UVLO threshold, rising VDD_UVLOVIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Cmin 3.3 · typ 3.6 · max 3.9 V4
VDD UVLO hysteresis VDD_UVLO_HYSTVIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Ctyp 300 mV4
Maximum VDD current IDDVIN = 6 V to 28 V; VEN = 5 V; TJ = -40 °C to +125 °Cmin 3 mA4
VDRV supply VDRVVIN = 6 V to 28 V; SiC43xB; VEN = 5 V; TJ = -40 °C to +125 °Cmin 4.75 · typ 5 · max 5.25 V4
Maximum VDRV current IDRVVIN = 6 V to 28 V; VEN = 5 V; TJ = -40 °C to +125 °Cmin 50 mA4
Input current IVINNon-switching, VFB > 0.6 V; VIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Ctyp 50 · max 120 uA4
Shutdown current IVIN_SHDNVEN = 0 V; VIN = 12 V; TJ = -40 °C to +125 °Ctyp 0.5 · max 3 uA4
Feedback voltage VFBTJ = 25 °C; VIN = 12 V; VEN = 5 Vmin 597 · typ 600 · max 603 m/V4
Feedback voltage VFBTJ = -40 °C to +125 °C (1); VIN = 12 V; VEN = 5 Vmin 594 · typ 600 · max 606 m/V4
VFB input bias current IFBVIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Ctyp 2 nA4
Minimum on-time tON_MIN.VIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Ctyp 50 · max 65 ns4
tON accuracy tON_ACCURACYVIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Cmin -10 · max 10 %4
On-time range tON_RANGEVIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Cmin 65 · max 2250 ns4
Minimum frequency, skip mode fSW_MIN.Power save version (SiC43xB); VIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Cmin 0 kHz4
Minimum off-time tOFF_MIN.VIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Cmin 205 · typ 250 · max 305 ns4
High side on resistance RON_HSSiC437; VDRV = 5 V, TA = 25 °Ctyp 10.1 m4
Low side on resistance RON_LSSiC437; VDRV = 5 V, TA = 25 °Ctyp 3.9 m4
Over current protection (inductor valley current) IOCL_PTJ = -10 °C to +125 °C; VIN = 12 V; VEN = 5 Vmin -20 · max 20 %4
Output OVP threshold VOVPVFB with respect to 0.6 V reference; VIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Ctyp 20 %4
Output UVP threshold VUVPVFB with respect to 0.6 V reference; VIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Ctyp -80 %4
Over temperature protection TOTP_RISINGRising temperature; VIN = 12 V; VEN = 5 Vtyp 150 °C4
Over temperature protection TOTP_HYSTHysteresis; VIN = 12 V; VEN = 5 Vtyp 25 °C4
Power good output threshold VFB_RISING_VTH_OVVFB rising above 0.6 V reference; VIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Ctyp 20 %4
Power good output threshold VFB_FALLING_VTH_UVVFB falling below 0.6 V reference; VIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Ctyp -10 %4
Power good hysteresis VFB_HYSTVIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Ctyp 40 mV4
Power good on resistance RON_PGOODVIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Ctyp 7.5 · max 15 4
Power good delay time tDLY_PGOODVIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Cmin 15 · typ 25 · max 35 us4
EN logic high level VEN_HVIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Cmin 1.6 V4
EN logic low level VEN_LVIN = 12 V; TJ = -40 °C to +125 °Cmax 0.4 V4
EN pull down resistance RENVIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Ctyp 5 M4
MODE1 (switching frequency) RMODE1fsw = 300 kHz; VIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Ctyp 51 · max 55 k4
MODE1 (switching frequency) RMODE1fsw = 500 kHz; VIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Cmin 90 · typ 100 · max 110 k4
MODE1 (switching frequency) RMODE1fsw = 750 kHz; VIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Cmin 180 · typ 200 · max 220 k4
MODE1 (switching frequency) RMODE1fsw = 1000 kHz; VIN = 12 V; VEN = 5 V; TJ = -40 °C to +125 °Cmin 450 · typ 499 · max 550 k4

Pins, by the datasheet

28
1 VIN
Input voltage. · p. 2
2 VIN
Input voltage. · p. 2
3 PGND
Power signal return ground. · p. 2
4 PGND
Power signal return ground. · p. 2
5 SW
Switching node signal; output inductor connection point. · p. 2
6 SW
Switching node signal; output inductor connection point. · p. 2
7 SW
Switching node signal; output inductor connection point. · p. 2
8 SW
Switching node signal; output inductor connection point. · p. 2
9 SW
Switching node signal; output inductor connection point. · p. 2
10 GL
Low side power MOSFET gate signal. · p. 2
11 GL
Low side power MOSFET gate signal. · p. 2
12 VDRV
Supply voltage for internal gate driver; connect a 2.2 uF decoupling capacitor to PGND. · p. 2
13 PGND
Power signal return ground. · p. 2
14 PGOOD
Power good signal output; open drain. · p. 2
15 VDD
Supply voltage for internal logic; connect a 1 uF decoupling capacitor to AGND. · p. 2
16 AGND
Analog signal return ground. · p. 2
17 FB
Output voltage feedback pin; connect to VOUT through a resistor divider network. · p. 2
18 VOUT
Output voltage sense pin. · p. 2
19 EN
Enable pin. · p. 2
20 MODE2
Soft start and current limit selection; connect a resistor to VDD or AGND per table 2. · p. 2
21 MODE1
Operating mode and switching frequency selection; connect a resistor to VDD or AGND per table 1. · p. 2
22 VIN
Input voltage. · p. 2
23 BOOT
Bootstrap pin; connect a capacitor to PHASE for HS power MOSFET gate voltage supply. · p. 2
24 PHASE
Switching node signal for bootstrap return path. · p. 2
25 AGND
Analog signal return ground. · p. 2
26 VIN
Input voltage. · p. 2
27 PGND
Power signal return ground. · p. 2
28 GL
Low side power MOSFET gate signal. · p. 2

Ordering codes, by the datasheet

1
SiC437BED-T1-GE3
PowerPAK® MLP44-24L · 12 A maximum current; internal VDD and VDRV; power saving light load mode; operating junction temperature -40 °C to +125 °C; part marking SiC437B. · p. 2

Open-source boards using it

4
  • 4 layers53.1 × 98 mmMarsupial, the printed circuit board in 3D

    Marsupial

    VIPQualityPost/marsupial

    2 port USB PD + data hub

    208 parts3
  • 4 layers85 × 40 mmWled controller, the printed circuit board in 3D

    Wled controller

    electro-practically/wled-controller

    WLED ESP32 controller powered by USB-C Power Delivery.

    99 partsCERN-OHL-P-2.0

Parts like it

6

Questions

Is there a KiCad symbol and footprint for the SIC437BED?

Yes. The symbol is Regulator_Switching:SIC437B and the footprint Package_DFN_QFN:Vishay_PowerPAK_MLP44-24L, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the SIC437BED?

PowerPAK-MLP44-24L, with 28 pins. Its footprint is drawn on this page.

Where is the SIC437BED datasheet?

Vishay Intertechnology publishes it: the Datasheet link on this page opens it.

Where can I order the SIC437BED?

JLCPCB lists it as part C2685654, with 412 in stock; the sellers' links on this page open their listings.

What can replace the SIC437BED?

Parts like it in the library: the SIC437AED by Vishay Intertechnology, the SIC431AED by Vishay Intertechnology, the SIC437CED by Vishay Intertechnology and the SIC431DED by Vishay Intertechnology. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the SIC437BED?

4 boards in 3 repositories on GitHub; the most starred are listed on this page, with their KiCad files.