Skip to the content
12345

PT4115

UMWExtended

-25℃~+85℃ 1.2A 1MHz 5% 6V~30V Analog、PWM Buck Built-in DC-DC Over-Temperature Protection (OTP) SOT-89-5 LED Drivers ROHS

Part id
umw/PT4115
Category
LED Drivers
Package
SOT-89-5
Pins
6
In stock
97,908 at JLCPCB (C347356)
Used on
16 open-source boards

Overview

The PT4115 is a LED Driver made by UMW in a SOT-89-5 package with 5 pins. -25℃~+85℃ 1.2A 1MHz 5% 6V~30V Analog、PWM Buck Built-in DC-DC Over-Temperature Protection (OTP) SOT-89-5 LED Drivers ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:PT4115B89E_C7421623, from EasyEDA) and its footprint (Package_TO_SOT_SMD:SOT-89-5, from KiCad's library), ready for a KiCad board. 97,908 are in stock at JLCPCB (part C347356). 16 open-source boards in 14 repositories on GitHub use it.

Symbol

1SW2GND3DIM4CSN5VIN
EasyEDA_Cloud:PT4115B89E_C7421623From EasyEDA

Footprint

12345
Package_TO_SOT_SMD:SOT-89-5From KiCad's library

From the datasheet

9
Supply, least
6 V · VIN, recommended operating min · p. 3
Supply, most
30 V · VIN, recommended operating max · p. 3
Supply, absolute maximum
35 V · VIN, absolute max · p. 3
Works from
-25 °C · Working temperature min · p. 3
Works up to
85 °C · Working temperature max · p. 3
Junction, hottest
150 °C · Working junction temperature absolute max · p. 3
Takes asleep
60 µA · Turn off current typical, VDIM < 0.3V · p. 4
Gives
1.2 A · SW continuous current max · p. 5
Junction to air (SOT89-5)
45 K/W · Junction to ambient thermal resistance · p. 3

What it is and has

4
Topology
Step-down constant current LED driver · p. 1
Power switch
Built in · p. 1
Protection
Thermal shutdown · p. 5
Package
SOT89-5 · p. 12

Around it

2
cap 4.7 μF minimum
between VIN and GND; DC input bypass; low ESR, X5R/X7R recommended, placed close to VIN. Larger capacitance is required for AC or low voltage input. · p. 9
res RS ≥ 0.082 Ω
between VIN and CSN; Current sampling resistor; sets average LED current to 0.1/RS. · p. 7

Specifications

33
ParameterConditionsAs printedPage
Supply voltage VINmin -0.3 · max 35 V3
Drain terminal of power switch SWmin -0.3 · max 35 V3
Current sampling terminal (relative VIN) CSNRelative to VIN; range printed as 0.3 to -6min -6 · max 0.3 V3
Switch enable, analog and PWM dimming terminals DIMmin -0.3 · max 6 V3
Power switch output current ISWmax 1.5 A3
Power waste(2) PDMAXmax 1.5 W3
Thermal resistance, SOT89-5 (θJA) CSCRSOT89-5max 45 °C/W3
Working junction temperature range TJmin -40 · max 150 °C3
Storage temperature range TSTGmin -55 · max 150 °C3
Supply voltage VINmin 6 · max 30 V3
Working temperature TOCSCmin -25 · max 85 °C3
input voltage VINTA=25°Cmin 6 · max 30 V4
Under voltage protection VUVLOTA=25°C; VIN decreasedtyp 5.1 V4
Under voltage protection hysteresis VUVLO, HYSTA=25°C; VIN increasedtyp 500 mV4
Maximum operating frequency FSWTA=25°C, VIN=12Vmax 1 MHz4
Average sampling voltage VCSNTA=25°C, VIN=12V; VIN − VCSNmin 95 · typ 100 · max 105 mV4
Input current of CSN pin ICSNTA=25°C, VIN=12V; VIN − VCSN=50mVtyp 8 uA4
Turn off current IOFFTA=25°C, VIN=12V; VDIM < 0.3Vtyp 60 uA4
Working voltage of internal circuit VDIMTA=25°C, VIN=12V; Dim floatingtyp 5 V4
Dim input high level VDIM_HTA=25°C, VIN=12Vmin 2.5 V4
Dim input low level VDIM_LTA=25°C, VIN=12Vmax 0.3 V4
Analog dimming voltage range VDIM_DCTA=25°C, VIN=12Vmin 0.5 · max 2.5 V4
Maximum PWM dimming frequency fDIMTA=25°C, VIN=12V; fOSC=500kHzmax 50 kHz4
Low frequency PWM dimming duty cycle range around DPWM_LFTA=25°C, VIN=12V; fDIM=100Hz; minimum printed as 0.02%, maximum printed as 1max 14
High frequency PWM dimming duty cycle range around DPPWM_HFTA=25°C, VIN=12V; fDIM=20kHz; minimum printed as 4%, maximum printed as 1max 14
Dim pull up internal working voltage resistance RDIMTA=25°C, VIN=12Vtyp 200 KΩ4
Dim earth leakage current IDIM_LTA=25°C, VIN=12V; VDIM=0typ 4.2 uA4
SW on resistance RSWTA=25°C; VIN =24Vtyp 0.4 Ω5
SW on resistance RSWTA=25°C; VIN =12Vtyp 0.6 Ω5
SW continuous current ISWmeanTA=25°C, VIN=12Vmax 1.2 A5
SW leakage current ILEAKTA=25°C, VIN=12Vtyp 0.5 · max 5 uA5
Overheat protection temperature TSDTA=25°C, VIN=12Vtyp 160 °C5
Overheating protection hysteresis TSD-hysTA=25°C, VIN=12Vtyp 20 °C5

Pins, by the datasheet

6
1 SW
Drain terminal of the internal power switch. · p. 2
2 GND
Power and signal ground. · p. 2
3 DIM
Switch enable, analog and PWM dimming terminal. · p. 2
4 CSN
Connect the sampling resistor between CSN and VIN. · p. 2
5 VIN
Power input; connect a bypass capacitor nearby. · p. 2
- Exposed PAD
Internally grounded cooling pad; attach to PCB to reduce thermal resistance. · p. 2

Ordering codes, by the datasheet

1
UMW PT4115
SOT89-5 · Base quantity 1000; tape and reel · p. 12

Open-source boards using it

16See all 16
  • 2 layers55 × 90 mmCCFL2LED, the printed circuit board in 3D

    CCFL2LED

    mijuc/CCFL2LED

    Hi! I'm working on the R&D side of the Поново project. Through our initiative, where we upcycle old electronic devices in exchange for tree seedlings, we’ve noticed that LCD monitors are among the most common items…

    82 parts7GPL-3.0
  • 2 layers128 × 100 mmSunface, the printed circuit board in 3D

    Sunface

    greenstitch315/sunface

    A big light for your face so you can wake up

    69 parts1MIT
  • 2 layers77 × 41 mmSottovasoLuminoso, the printed circuit board in 3D

    SottovasoLuminoso

    paoloach/LuminousSaucer

    A simple light for indoor plants

    20 parts1Apache-2.0
  • 2 layers65.1 × 46.1 mmRgbleddriver, the printed circuit board in 3D

    Rgbleddriver

    tunaerray/3w-rgb-led-driver

    3W RGB LED driver board with PWM dimming for AUV image processing

    29 parts1
  • 2 layers90 × 27 mmPower, the printed circuit board in 3D

    Power

    Edgeworth/memered

    61 parts
  • 2 layers50.5 × 47.5 mmDiy led spot step3, the printed circuit board in 3D

    Diy led spot step3

    FaisalHussain95/esp32-espnow-led-spots

    DIY 220VAC LED spot controller — ESP32-C3 + COB LED + PT4115 PWM dimming, NTC thermal protection, active fan cooling, ESP-NOW mesh. WiFi bridge for Home Assistant (MQTT).

    37 parts
  • 2 layers99.6 × 69.6 mmRGBW Lampe, the printed circuit board in 3D

    RGBW Lampe

    martinclausen2/RGBW-Lampe

    The "RGBW-Lampe" projects allows to create full color lighting appliances.

    162 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the PT4115?

Yes. The symbol is EasyEDA_Cloud:PT4115B89E_C7421623 and the footprint Package_TO_SOT_SMD:SOT-89-5, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the PT4115?

SOT-89-5, with 5 pins. Its footprint is drawn on this page.

Where is the PT4115 datasheet?

UMW publishes it: the Datasheet link on this page opens it.

Where can I order the PT4115?

JLCPCB lists it as part C347356, with 97,908 in stock; the sellers' links on this page open their listings.

What can replace the PT4115?

Parts like it in the library: the AL8861Y by Diodes Incorporated, the PT4115B89E by PowTech, the SN3360GP05E by Si-En Tech and the PT4115B89E-B by PowTech. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the PT4115?

16 boards in 14 repositories on GitHub; the most starred are listed on this page, with their KiCad files.