Skip to the content

TPSM84338RCJR

Texas InstrumentsExtended

-40℃~+125℃ 1 200kHz~2.2MHz 28uA 3.8V~28V 3A 600mV~17V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Adjustable soft-start、Operating status indication、Cycle-by-cycle current limiting、Frequency synchronization、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes QFN-FCMOD-9 DC-DC Converters ROHS

Part id
ti/TPSM84338RCJR
Category
DC DC Converters
Package
QFN-9_3.3x4.5mm
Pins
9
In stock
2,966 at JLCPCB (C47122151)
Used on
8 open-source boards

Overview

The TPSM84338RCJR is a DC DC Converter made by Texas Instruments in a QFN-9_3.3x4.5mm package with 9 pins. -40℃~+125℃ 1 200kHz~2.2MHz 28uA 3.8V~28V 3A 600mV~17V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Adjustable soft-start、Operating status indication、Cycle-by-cycle current limiting、Frequency synchronization、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes QFN-FCMOD-9 DC-DC Converters ROHS.

PCBKit's library has its footprint (EasyEDA_Cloud:QFN-FCMOD-9_L4.5-W3.3_TPSM84338, from EasyEDA), ready for a KiCad board. 2,966 are in stock at JLCPCB (part C47122151). 8 open-source boards in 5 repositories on GitHub use it.

Symbol

The library has no symbol for this part yet.

Footprint

EasyEDA_Cloud:QFN-FCMOD-9_L4.5-W3.3_TPSM84338From EasyEDA

From the datasheet

14
Supply, least
3.8 V · VIN, recommended operating min · p. 5
Supply, most
28 V · VIN, recommended operating max · p. 5
Supply, absolute maximum
30 V · VIN, absolute max · p. 5
Junction, hottest
125 °C · junction temperature max · p. 5
Takes working
28 µA · VIN quiescent current typical, PFM, EN = 5 V, VFB = 0.65 V, VIN = 12 V · p. 6
Takes asleep
3 µA · shutdown current typical, VEN = 0 V, VIN = 12 V · p. 6
Gives
3 A · continuous output current max · p. 5
Current limit
6.5 A · high-side MOSFET current limit typical, VIN = 12 V · p. 6
Current limit
4.5 A · low-side MOSFET current limit typical, VIN = 12 V · p. 6
Feedback reference
600 mV · FB reference typical, TJ = -40°C to 125°C · p. 6
Junction to air (RCJ (QFN-FCMOD),9 引脚)
55.2 K/W · junction to ambient, JEDEC typical · p. 5
Junction to case (RCJ (QFN-FCMOD),9 引脚)
58.1 K/W · junction to case top, JEDEC typical · p. 6
Junction to board (RCJ (QFN-FCMOD),9 引脚)
16 K/W · junction to board, JEDEC typical · p. 6
Junction to air (RCJ (QFN-FCMOD),9 引脚)
46 K/W · junction to ambient on official EVM, typical · p. 6

What it is and has

9
Input voltage range
3.8V to 28V · p. 1
Output voltage range
0.6V to 17V · p. 1
Continuous output current
3A · p. 1
Reference accuracy
0.6V ±1%, –40°C to 125°C · p. 1
Control
Peak current mode, internal compensation · p. 1
Selectable switching frequency
200kHz to 2.2MHz · p. 1
Soft start and power good
Selectable adjustable soft-start time / power-good indicator · p. 1
Integrated components
Bootstrap capacitor and inductor · p. 1
Package
3.3mm × 4.5mm × 2mm QFN · p. 1

Around it

4
cap 10μF
between VIN and GND; Typical input decoupling value; X5R or X7R ceramic recommended. · p. 26
cap 0.1μF
between VIN and GND; Additional capacitor for high-frequency filtering; connect directly to VIN and GND. · p. 26
cap 3 × 10μF
between VIN and GND; Example design: three Murata GRM32ER7YA106KA12K, 35V, 1210, X7R capacitors. · p. 26
cap 22pF
between VOUT and FB; Optional example feedforward capacitor C7 across RFBT to improve load transient performance. · p. 26

Specifications

47
ParameterConditionsAs printedPage
输入电压 VINmin -0.3 · max 30 V5
输入电压 ENmin -0.3 · max 6 V5
输入电压 FBmin -0.3 · max 6 V5
输出电压 VOUTmin -0.3 · max 18 V5
输出电压 SS/PGmin -0.3 · max 6 V5
输出电压 MODEmin -0.3 · max 6 V5
输出电压 RT/SYNCmin -0.3 · max 6 V5
机械冲击Mil-STD-883D,方法 2002.3,1ms,1/2 正弦,已安装max 1500 G5
机械振动Mil-STD-883D,方法 2007.2,20Hz 至 2000Hzmax 20 G5
工作结温(2) TJmin -40 · max 125 °C5
贮存温度 Tstgmin -65 · max 125 °C5
静电放电 V(ESD)人体放电模型 (HBM),符合 ANSI/ESDA/JEDEC JS-001 标准,所有引脚min -3000 · max 3000 V5
静电放电 V(ESD)充电器件模型 (CDM),符合 ANSI/ESDA/JEDEC JS-002 标准,所有引脚min -1000 · max 1000 V5
输入电压 VINmin 3.8 · max 28 V5
输入电压 ENmin -0.1 · max 5.5 V5
输入电压 FBmin -0.1 · max 5.5 V5
输入电压 SS/PGmin -0.1 · max 5.5 V5
输入电压 MODEmin -0.1 · max 5.5 V5
输出电压 VOUTmin 0.8 · max 17 V5
输出电流 IOUTmin 0 · max 3 A5
温度 TJ工作结温min -40 · max 125 °C5
结至环境热阻 RθJARCJ (QFN-FCMOD),9 引脚; JEDECtyp 55.2 °C/W5
结至外壳(顶部)热阻 RθJC(top)RCJ (QFN-FCMOD),9 引脚; JEDECtyp 58.1 °C/W6
结至电路板热阻 RθJBRCJ (QFN-FCMOD),9 引脚; JEDECtyp 16 °C/W6
结至电路板特征参数 ΨJBRCJ (QFN-FCMOD),9 引脚; JEDECtyp 15.7 °C/W6
官方 EVM 板上的结至环境热阻 RθJA_EVMRCJ (QFN-FCMOD),9 引脚; EVMtyp 46 °C/W6
工作输入电压 VINmin 3.8 · max 28 V6
非开关静态电流 IQEN = 5V,VFB = 0.65V,VIN = 12V,PFMtyp 28 · max 34 uA6
非开关静态电流 IQEN = 5V,VFB = 0.65V,VIN = 12V,FCCMtyp 40 · max 47 uA6
关断电源电流 ISHDNVEN = 0V,VIN = 12Vtyp 3 · max 5.5 uA6
输入欠压锁定阈值 VIN_UVLO上升阈值min 3.4 · typ 3.6 · max 3.8 V6
输入欠压锁定阈值 VIN_UVLO下降阈值min 3.2 · typ 3.4 · max 3.6 V6
输入欠压锁定阈值 VIN_UVLO迟滞typ 200 mV6
启用阈值 VEN_RISE上升使能阈值typ 1.15 · max 1.22 V6
禁用阈值 VEN_FALL下降禁用阈值min 0.9 · typ 1 V6
EN 上拉电流 IpVEN = 1.0Vtyp 0.7 uA6
EN 上拉迟滞电流 Ihtyp 1.76 uA6
FB 电压 VFBTJ = 25°Cmin 596 · typ 600 · max 604 mV6
FB 电压 VFBTJ = 0°C 至 85°Cmin 595 · typ 600 · max 605 mV6
FB 电压 VFBTJ = -40°C 至 125°Cmin 594 · typ 600 · max 606 mV6
输入漏电流 IFBVIN = 12V,VFB = 0.8V,TJ = 25°Cmax 0.1 uA6
高侧 MOSFET 电流限制 IHS_LIMITVIN = 12Vmin 5.6 · typ 6.5 · max 7.4 A6
低侧 MOSFET 电流限值 ILS_LIMITVIN = 12Vmin 3.6 · typ 4.5 · max 5.6 A6
反向电流限制 ILS_NOCVIN = 12Vmin 2 · typ 3 · max 4.2 A6
最小峰值电感器电流 IPEAK_MINVIN = 12Vtyp 1.2 A6
软启动充电电流 ISSmin 3.5 · typ 5.5 · max 6.5 uA6
固定内部软启动时间 TSS具有 PG 功能的模式。从 0% Vout 到 90% Vout 的时间typ 3.6 ms6

Ordering codes, by the datasheet

2
TPSM84338RCJR
QFN-FCMOD (RCJ) | 9 · 3000 | LARGE T&R; -40 to 125°C; NIPDAU; marking M84338 · p. 36
TPSM84338RCJR.A
QFN-FCMOD (RCJ) | 9 · 3000 | LARGE T&R; -40 to 125°C; NIPDAU; marking M84338; no other difference stated · p. 36

Open-source boards using it

8
  • 4 layers96 × 125.6 mmPowerDistributionPCB, the printed circuit board in 3D

    PowerDistributionPCB

    CUSail-Navigation/PCB-FA25-SP26

    This is a repository containing the PCBs designed during the FA25-SP26 academic year. Due to high compatibility and relative ease of use, all of these files are made with KiCad.

    93 parts
  • 4 layers29 × 42 mmRollxoxo shim, the printed circuit board in 3D

    Rollxoxo shim

    Galacs/rollxoxo-shim

    Shim pcb to allow remote control of rollxio garage door via wifi or bluetooth

    72 parts
  • 4 layers38.9 × 23.3 mmOWL - Rotor v2, the printed circuit board in 3D

    OWL - Rotor v2

    sedlak477/owl-hardware

    Hardware design files and build instructions for the OWL platform

    118 partsCERN-OHL-P-2.0
  • 2 layers133 × 88 mmSonosHack backup, the printed circuit board in 3D

    SonosHack backup

    smariel/SonosPlay1Hack

    Sonos Play:1 replacement with RaspberryPi

    58 partsCERN-OHL-W-2.0
  • 4 layersReal Power double5V, the printed circuit board in 3D

    Real Power double5V

    CUSail-Navigation/PCB-FA25-SP26

    This is a repository containing the PCBs designed during the FA25-SP26 academic year. Due to high compatibility and relative ease of use, all of these files are made with KiCad.

    89 parts
  • 2 layers160 × 122 mmJackOfAllTradesV1p0, the printed circuit board in 3D

    JackOfAllTradesV1p0

    czalinski/ThlHwTestDevices

    KiCad designs, firmware and documentation for circuits that support testing of electrical hardware, such as HASS and HALT testing.

    119 partsMIT
  • 2 layers100 × 100 mmPocDcPowerV1p0, the printed circuit board in 3D

    PocDcPowerV1p0

    czalinski/ThlHwTestDevices

    KiCad designs, firmware and documentation for circuits that support testing of electrical hardware, such as HASS and HALT testing.

    43 partsMIT
  • 4 layers133 × 88 mmSonosHack backup, the printed circuit board in 3D

    SonosHack backup

    smariel/SonosPlay1Hack

    Sonos Play:1 replacement with RaspberryPi

    52 partsCERN-OHL-W-2.0

Questions

Is there a KiCad symbol and footprint for the TPSM84338RCJR?

Yes. the footprint EasyEDA_Cloud:QFN-FCMOD-9_L4.5-W3.3_TPSM84338, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPSM84338RCJR?

QFN-9_3.3x4.5mm, with 9 pins. Its footprint is drawn on this page.

Where is the TPSM84338RCJR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPSM84338RCJR?

JLCPCB lists it as part C47122151, with 2,966 in stock; the sellers' links on this page open their listings.

Which open-source boards use the TPSM84338RCJR?

8 boards in 5 repositories on GitHub; the most starred are listed on this page, with their KiCad files.